Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D Manual de usuario Pagina 41
- Pagina / 98
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 6000-IN007A-EN-P - October 2014 41
Commissioning Chapter 3
Verify Operation of Frequency Steps
There are two parts to this procedure, increasing the frequency in set increments
and increasing the frequency to a specific rated frequency.
Increase Frequency by Step
1. From the Main Interface Screen, press the Set Frequency: input field.
2. In the Set Freq: dialog box, enter a value of “10” and press .
Press to confirm.
TIP
Durh
During the Control System Check procedure, an “Abnormal Output Voltage
Warning” will appear, as the procedure is done without MV and the Control
System is expecting an output voltage. Ignore this warning for this procedure.
TIP
The Set Frequency and Actual Frequency occasionally will not show the exact
integral value selected, due to internal data conversion in the HMI program.
- Commissioning Manual 1
- Important User Information 2
- Table of Contents 3
- Table 1 - Electrical Drawings 7
- General Precautions 9
- Additional Resources 9
- Introduction 11
- Documentation and 12
- Application Review 12
- Review Drive Application 13
- Chapter 1 Introduction 14
- Preparation and Inspection 15
- Inspect Drive Components 16
- Functional Assessment 17
- Interconnection Review 20
- Installation Review 21
- Power Cabling 22
- Drive Megger Check 23
- Figure 4 - Control Switches 25
- Figure 5 - Control Switches 25
- Figure 8 - Back of HMI 26
- Connect the Insulation Meter 27
- Final Steps before 29
- Equipment is Ready for 29
- Energization 29
- Commissioning 31
- Control System Check Setup 32
- Control System Check 35
- , press 36
- Access Setup Settings 37
- Set P Parameters 38
- Commissioning Chapter 3 39
- Chapter 3 Commissioning 40
- Increase Frequency by Step 41
- Simulate Warnings and Faults 45
- Verify E-Stop Functionality 50
- (Manual Bypass) 52
- Bypass Isolation Switches 54
- (Automatic Bypass) 55
- , and press 57
- Bypass Contactors 58
- Figure 17 - Status Indicators 61
- Table 9 - Drive to DCS 61
- Table 10 - 4-20 mA 61
- Restore P Parameter Settings 62
- Set Date and Time Zone 64
- No-load Test 67
- Configure P and T Parameters 68
- 0 ON -100 199.99 R&D 69
- (2) With Remote DCS only 70
- Parameters T11...T13 71
- Chapter 4 No-load Test 72
- Change Parameter T12: 73
- 3. Press to accept 73
- Close Input Circuit Breaker 75
- Check Cooling Fan Operation 75
- Operate Motor by HMI 76
- No-load Test Chapter 4 77
- Press to confirm 78
- Load Test of Drive System 80
- Torque Requirements 81
- Single Line Diagrams 83
- Appendix C 87
- Overview 87
- System Setting Functions 87
- Switch Control Sources 88
- Motor Parameter Setting 88
- Restore Factory Setting 89
- Speed Command Functions 90
- Frequency Amplitude Limit 91
- Frequency Skip 91
- Speed Reference Functions 92
- Analog Input 93
- Stop Mode 93
- Flying Start Function 93
- Restart the Drive 94
- Rockwell Automation Support 98
- Documentation Feedback 98
Relacionado con productos y manuales para Equipo Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D
Equipo Rockwell-automation 2711PC-xxxx PanelView Plus 6 Compact Terminals Use Manual de usuario
(162 paginas)
(162 paginas)
Equipo Rockwell-automation 6181P_F VersaView 6181P Integrated Display Compute Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 2090-XBxxx Resistive Brake Module Installation Ins Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 2364F Regenerative DC Bus Supply Unit (RGU) Manual de usuario
(222 paginas)
(222 paginas)
Equipo Rockwell-automation 2090-CSWMxxx Single Motor Cables with Circular DIN Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2090-CBUSPSS Kinetix 6000M Bulkhead Cable Adapter Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 2090-CSBM1DF-10AF Single Motor Cables with Circula Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2080 Micro800 Digital and Analog Plug-in Modules Manual de usuario
(108 paginas)
(108 paginas)
Equipo Rockwell-automation MV SMC Flex OEM Components - Fiber Optic Cables Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 2094-EN02D-M01-S0 Kinetix 6200 and Kinetix 6500 Sa Manual de usuario
(42 paginas)
(42 paginas)
(52 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales