Rockwell-automation 61C23 AutoMate Local I/O Head Manual de usuario Pagina 1

      

2Ć2TO PROCESSOR, LOCAL I/O PROCESSOROR REMOTE HEADINPUTRAIL 0RAIL 1RAIL 3RAIL 2POWERCOMRAIL FAULT 0RAIL FAULT 1RAIL FAULT 2RAIL FAULT 3AutoMateLOCAL H

3Ć13.0 INSTALLATIONThis section describes how to install the Local I/O Head.DANGERTHE USER IS RESPONSIBLE FOR CONFORMING WITH THE NATIONALELECTRICAL C

3Ć2Step 5. Connect the Local I/O Interface cable between the LocalI/O Head connector labeled INPUT and any Rail connectoron the hardware with which th

4Ć14.0 CONFIGURATIONConfiguration is a method of describing how the system software andthe I/O are related. The process of configuring the Local I/O H

4Ć2Sample configuration with four Rails connected to the Local I/O Headand the Master 30 or 40 Processor in slot 1:MSLT DROP TYPE RSLOT CARD CH0 REG C

4Ć34.3 Local I/O Head with AutoMate RemoteI/O HeadWhen using the Local I/O Head with the AutoMate Remote I/O Head,only the first register of the four

4Ć4m Ć Slot in rack containing DCS 5000/AutoMax masterRemote I/O module. This number may range from 0 to15.d Ć Drop number of DCS 5000/AutoMax Remote

5Ć15.0 DIAGNOSTICS ANDTROUBLESHOOTINGDANGERTHE REMAINING STEPS ARE MADE WITH POWER ON. EXERCISE EXTREMECAUTION BECAUSE HAZARDOUS VOLTAGE EXISTS. FAILU

5Ć25.2 The COM LED Is OffProblem: The COM LED on the faceplate is off. When lit, this LEDsignifies that there is communication between the Local I/O H

5Ć3Step 3. Turn on power to the Local I/O Head and put theapplication program(s) into run. If any RAIL FAULT LEDsturn on, stop application tasks and t

"!$t  "t  !   ! %  ! && "  r  "!!r   !

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

AĆ1Appendix ATechnical SpecificationsM/N 61C22Ambient ConditionsD Storage temperature: -20_ Ć85_CD Operating temperature: 0_ Ć60_CD Humidity: 5Ć90% no

AĆ2Appendix A(Continued)M/N 61C23Ambient ConditionsD Storage temperature: -20_ Ć85_CD Operating temperature: 0_ Ć60_CD Humidity: 5Ć90% nonĆcondensingM

Appendix BLocal I/O Head Mounting Pattern 

BĆ2Appendix B(Continued)MOUNTING SURFACELOCAL HEADMOUNTING FLANGEBOLTSTAR WASHERTAPPED HOLESTAR WASHERWELDED STUDBACK PANELNUTLOCAL HEADMOUNTINGFLANGE

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

For additional information1 Allen-Bradley DriveMayfield Heights, Ohio 44124 USATel: (800) 241-2886 or (440) 646-3599http://www.reliance.com/automaxCop

ITable of Contents1.0 Introduction 1Ć1...1.1 Additional Information 1Ć1...

II Technical SpecificationsM/N 61C22 AĆ1...M/N 61C23 AĆ2...

III  Figure 2.1 Ć Local I/O Head (120 VAC) 2Ć1...Figure 2.2 Ć Local I/O Head (24/48 VDC) 2Ć2...

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

1Ć11.0 INTRODUCTIONThe products described in this instruction manual are manufacturedor distributed by Reliance Electric Industrial Company.The Local

1Ć2D E/M 0Ć45C33 DCS 5000/AutoMax Remote I/O Head InstructionManualD Other instruction manuals applicable to your hardwareconfigurationD IEEE 518 GUID

2Ć12.0 MECHANICAL/ELECTRICALDESCRIPTIONThe Local I/O Heads incorporate a custom chip and an internalpower supply. Model Numbers 61C22 and 61C23 are id