Rockwell-automation 1336F PLUS II Custom Firmware Inst. - EN916 Manual de usuario descargar pdf (Pagina 2)

2 EN916 - Variable Voltage Control

Voltage Control

[Volt Decr Time]

Thisvaluedeterminesthetimeitwilltakethedrivetoramp

from [Maximum Voltage] to 0 Volts when [Control Select]

is set to “Variable Voltage”. The rate determined by this

value and [Maximum Voltage] is linear.

Parameter Number 335

Parameter Type Read and Write

Display Units / Drive Units 0.1 Second / Seconds x 10

Factory Default 10.0 Sec

Minimum Value 0.0 Sec

Maximum Value 3600.0 Sec

[Voltage Command]

This parameter displays the commanded voltage value

from the reference speciﬁed by [Volt Select].

Parameter Number 336

Parameter Type Read Only

Display Units / Drive Units 1 Volt / 4096 = Drive Rated Volts

Factory Default None

Minimum Value 0 Volts

Maximum Value 120% Rated Drive Output Voltage

[Volt Select]

This parameter speciﬁes which input signal will be used

asthe [Volt Command]referencewhen[Control Select]is

set to “Variable Voltage”.

Parameter Number 337

Parameter Type Read and Write

Factory Default “Volt Preset”

Units Display Drive

“Analog In 0” 0

“Analog In 1” 1

“Analog In 2” 2

“Volt Preset” 3 Refer to [Volt Preset] Value

“Adapter 1-6” 4-9

“Volt Cmd Ref” 10 Refer to [Volt Command Ref] Value

“Pre+AI0 Trim” 11 Refer to [Volt Trim%] Value

“Pre+AI1 Trim” 12

“Pre+AI2 Trim” 13

“Pre+Trim Ref” 14 Refer to [Volt Trim% Ref] Value

[Volt Preset]

Thisparameterspeciﬁestheoutputvoltagesetpointvalue

when [Volt Select] is set to “Volt Preset”.

Parameter Number(s) 338

Parameter Type Read and Write

Display Units / Drive Units 1 Volt / 4096 = Drive Rated Volts

Factory Default 0 Volts

Minimum Value 0 Volts

Maximum Value 120% Drive Rated Volts

[Volt Trim%]

This parameter speciﬁes the volt trim% value when [Volt

Select] is set to “Pre + AIx Trim”. The value represents

±Volt Trim% of [Rated Voltage].

Minimum Input = –Volt Trim% Value

Mid-Point Input = No Trim

Maximum Input = +Volt Trim% Value

Parameter Number 339

Parameter Type Read and Write

Display Units / Drive Units 1% / 4096 = 100%

Factory Default 10%

Minimum Value 0%

Maximum Value +100%

[Volt Command Ref]

This parameter speciﬁes the drive output voltage when

[VoltSelect]issetto“VoltCmdRef”. Theparametervalue

is cleared at power-up and is not retained in eeprom

storage. This parameter is intended to be used with a

SCANport communications adapter via the [Data In xx]

Adapter I/O parameters.

Parameter Number(s) 340

Parameter Type Read and Write

Display Units / Drive Units 1 Volt / 4096 = Drive Rated Volts

Factory Default 0 Volts

Minimum Value 0 Volts

Maximum Value 120% Drive Rated Volts

1 2 3 4

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 1336F PLUS II Custom Firmware Inst. - EN916 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 1336F PLUS II Custom Firmware Inst. - EN916