Rockwell-automation 1336F PLUS II Quick Start Guide Manual de usuario descargar pdf (Pagina 1)

PE PE

(L1)

(L2)

(L3)

(T1)

(T2)

(T3)

–

Dynamic Brake

Required

Input Fusing

Required Branch

Circuit Disconnect

Shield

Common Mode Core*

Diagram shows connections that are common for all drives.

Refer to User Manual for Detailed Information.

Ground per

Local Codes

Motor Frame

Motor

Terminator*

* Optional

Nearest

Building Structure Steel

AC Input

to Drive

Ground

Drive Output

to Motor

(Not on all drives) (Not on all drives)

Conduit/4-Wire Cable

BRK

–

Important: Verify motor insulation system peak voltage

rating. For cable lengths greater than 6.1

meters (20 feet), consult the User Manual.

Power Wiring – TB1

Digital Outputs – TB2

Only Present

on B Frame

& Up Drives

Reserved for

Future Use

CR2

CR1 CR3CR3 CR4CR4

11 12 13 14 15 16 17 18 A1 A2

Terminal

10, 11

11, 12

13, 14

14, 15

16, 17

17, 18

A1, A2

Signal

True Earth - Shield Termination

CR1 Programmable Contact

CR2 Programmable Contact

CR3 Programmable Contact

CR4 Programmable Contact

Reserved for Future Use

Resistive Rating = 115V AC/30V DC, 5.0A

Inductive Rating = 115V AC/30V DC, 2.0A

Contacts Shown in Unpowered State

(or Powered State with Fault/Alarm Present)

Important: On A Frame Drives, the power supply used for relay contact outputs requires a field installation of

transient voltage surge suppression with maximum clamping voltage of 2.5 kV on all control boards.

1336 PLUS II Quick Start Guide

This Quick Start Guide summarizes the basic steps needed to install, start-up and program the 1336 PLUS II Adjustable

Frequency AC Drive. The information provided Does Not replace the User Manual and is intended for qualif

ied drive service

personnel

only. Refer to the 1336

PLUS II User Manual (publication 1336 PLUS-5.3) for details on other application

considerations and related precautions.

Publication 1336 PLUS-5.9ML – June, 2003 P/N 188747 (06)

1 2 3 4 5 6

Indice de contenidos

Pagina 1 - PLUS II Quick Start Guide

PE PER(L1)TES(L2)T(L3)U(T1)V(T2)W(T3)DC+DC–Dynamic BrakeRequiredInput FusingRequired BranchCircuit DisconnectShieldCommon Mode Core*Diagram shows conn

Pagina 2 - Jumper Locations

1336 PLUS II Quick Start Guide192021222324252627282930!A hazard of personal injury from automatic restart exists with 2-wire control. 2-wire control u

Pagina 3 - Start-Up

This start-up procedure covers only the most commonly adjusted values using the 1336 PLUS II “Startup” mode. Refer to theUser Manual for detailed info

Pagina 4 - HIM Operation

1336 PLUS II Quick Start Guide❑ 5. If Analog Option is installed, verify that DIP switch(es) are properly set (refer to Option Instruction Sheet). ATT

Pagina 5

1336 PLUS II Quick Start GuideProcess DisplayPower-Up Mode &Status DisplayESC SELor or or orOPERATOR LEVELMODE LEVELGROUP LEVELOutput Current (54)

Pagina 6 - Read Only

Speed Control (77)PI Config (213)PI Status (214)PI Ref Select (215)PI Fdbk Select (216)PI Reference (217)PI Feedback (218)PI Error (219)PI Output (220