Rockwell-automation 1794-AENTR_AENTRXT FLEX I/O Dual Port EtherNet/IP Manual de usuario descargar pdf (Pagina 5)

FLEX I/O™ Dual Port EtherNet/IP Adapter Modules 5

Publication 1794-IN131A-EN-P - January 2012

General Specifications

Indicator Status

Link 1 or Link 2 (individually)

Off No link exists. Verify network cabling. Correct as necessary.

Solid green Link exists at 100 Mbps.

Flashing green I/O is being transmitted or received at 100 Mbps.

Flashing yellow I/O is being transmitted or received at 10 Mbps.

Solid yellow Link exists at 10 Mbps.

Module Status Indicator

Off No power. Adapter does not have 24V DC power. Make sure

power is being supplied to the adapter.

Flashing green Standby. Adapter not configured. Configure adapter.

Green Operational. Adapter operating correctly. No action

required.

Flashing red Minor fault. A recoverable fault has been detected. This

could be caused by an incorrect or inconsistent

configuration.

Check configuration and reconfigure as needed.

Solid red Major fault. An unrecoverable fault has been detected.

Recycle power to the adapter. If this does not clear the

fault, replace the adapter.

Flashing red/green Self test. Adapter performing power-up self test. Wait until

completed.

Network Status Indicator

Off Not powered. No IP address. Adapter is not powered or

does not have an IP address.

Verify there is power and the adapter is correctly wired to

the power supply.

Make sure the adapter is configured.

Flashing green No connection. Adapter has obtained an IP address, but has

no established connections.

Green CIP connections. Adapter has an IP address and at least one

established connection.

Flashing red Connection timeout. One or more of the connections in

which the adapter is the target has timed out.

Red Duplicate IP address. Adapter has detected that its IP

address is already in use. Configure the adapter with a

unique IP address.

Flashing red/green Self-test. Adapter performing power-up self test.

Attribute Value

I/O capacity 8 modules

Power supply To comply with the CE Low Voltage Directive (LVD), this

equipment must be powered from a source compliant with

the following:

Safety Extra Low Voltage (SELV) or Protected Extra Low

Voltage (PELV).

Input voltage rating,

nom

24V DC

Input voltage range 19.2…31.2V DC (includes 5% AC ripple)

Inrush current 18 A for 2 ms

Communication rate 10/100 Mbps

Indicators Module status – red/green

Network status – red/green

Link 1 – yellow/green

Link 2 – yellow/green

FlexBus output 5.0V DC

640 mA, max

Isolation voltage 50V (continuous), Basic Insulation Type

Tested @ 1000V AC for 60 s, power to FlexBus to EtherNet

Power consumption,

max

500 mA,

400 mA @ 24V DC

Power dissipation, max 7.1 W @ 19.2V DC

Thermal dissipation 24.2 BTU/hr @ 19.2V DC

Ethernet connector RJ45 Cat. 5

Enclosure type rating None (open-style)

Wire size Power conductors:

0.33…3.31 mm

(22…12 AWG) stranded copper wire rated

@ 75

°C (167 °F) or greater, 1.2 mm (3/64 in.) insulation

max

Wiring category

(1)

Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation

Wiring and Grounding Guidelines, publication

1770-4.1.

1 – on power ports

2 – on communication ports

North American temp

code

T5 – 1794-AENTR

T4A – 1794-AENTRXT

IEC temp code T5 – for 1794-AENTR

T4 – for 1794-AENTRXT

Terminal screw torque 0.8 Nm (7 lb-in.)

Weight, approx. 227 g (8.01 oz)

Dimensions, HxWxD,

approx.

87.4 x 94 x 92 mm

(3.44 x 3.7 x 3.6 in.)

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 1794-AENTR_AENTRXT FLEX I/O Dual Port EtherNet/IP Manual de usuario Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 1794-AENTR_AENTRXT FLEX I/O Dual Port EtherNet/IP