Rockwell-automation 20P PowerFlex DC Drive - Frame B Switching Power S Manual de usuario

Busca en linea o descarga Manual de usuario para Equipo Rockwell-automation 20P PowerFlex DC Drive - Frame B Switching Power S. Rockwell Automation 20P PowerFlex DC Drive - Frame B Switching Power Supply Circuit Board User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 10
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Installation Instructions
PowerFlex
®
DC Drive - Frame B Switching
Power Supply Circuit Board
What This Kit Includes
Switching Power Supply circuit board
16 Pin Ribbon cable
Four screws with captive lock washers
Four metal stand-offs
Two plastic screws
Two plastic stand-offs
SA-SB terminal block
Static strap
Tools That You Need
Phillips
®
screwdriver
Flathead screwdriver
Nut driver or wrench for hex stand-offs
Phillips
®
is a registered trademark of Phillips Screw Company.
ATTENTION: Only qualified personnel familiar with DC
drives and associated machinery should plan or implement the
installation, start-up and subsequent maintenance of the system.
Failure to comply may result in personal injury and/or equipment
damage.
ATTENTION: To avoid an electric shock hazard, ensure that all
power to the drive has been removed before performing the
following.
ATTENTION: This drive contains ESD (Electrostatic
Discharge) sensitive parts and assemblies. Static control
precautions are required when installing, testing, servicing or
repairing this assembly. Component damage may result if ESD
control procedures are not followed. If you are not familiar with
static control procedures, reference A-B publication 8000-4.5.2,
“Guarding Against Electrostatic Damage” or any other
applicable ESD protection handbook.
Vista de pagina 0
1 2 3 4 5 6 7 8 9 10

Indice de contenidos

Pagina 1 - Power Supply Circuit Board

Installation InstructionsPowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board What This Kit Includes• Switching Power Supply circuit bo

Pagina 2 - Step 1: Remove Power

Publication 20P-IN006B-EN-P - December 2009Supersedes 20P-IN006A-EN-P - March 2009 Copyright © 2009 Rockwell Automation. All rights reserved. Printed

Pagina 3 - Step 2: Remove the

2 PowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board What You Need to DoTo install the Switching Power Supply board:❐ Step 1: Remove p

Pagina 4 - Pull tabs out

PowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board 3 Step 2: Remove the Protective Covers1. Disconnect the DPI cable from the HIM asse

Pagina 5 - Supply Board

4 PowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board 4. Disconnect the HIM Communication cable from the connector on the upper right c

Pagina 6

PowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board 5 Step 3: Remove the Existing Switching Power Supply BoardNote: The Switching Power

Pagina 7 - Remove screws

6 PowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board 3. Remove the plug-in terminal from the field input block at the top of the drive

Pagina 8 - Remove cable from XV

PowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board 7 6. Remove the cable from connector XP in upper right corner of the Pulse Transfor

Pagina 9 - Switching Power Supply

8 PowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board 8. Remove the cables from connectors XV and XUV on the Switching Power Supply boa

Pagina 10 - Related Documentation

PowerFlex® DC Drive - Frame B Switching Power Supply Circuit Board 9 Step 4: Install the New Switching Power Supply Board1. Install the new Switching

Comentarios a estos manuales

Sin comentarios