2Ć2There are 16 LEDs on the faceplate of the module. The LEDs arearranged in the same order as the output terminals on the faceplate.They are numbered
3Ć1 This section describes how to install and remove the module and itscable assembly. The installation of wiring should confo
2$".+ 2 1*$& $ & $"(& )(( -$)(,- * % -# &a
3Ć3P/S012345678910111213141510Typical 10 Slot Rack16Typical 16 Slot RackFigure 3.2 Ć Rack Slot NumbersStep 6. Attach the field terminal connector (M/N
3Ć4WARNINGBE CAREFUL WHEN WRITING TO THE OUTPUTS TO INSURE THAT NOUNEXPECTED MACHINE MOTION WILL RESULT. FAILURE TO OBSERVE THISPRECAUTION COULD RESUL
4Ć14.0 PROGRAMMINGThis section describes how data is organized in the module andprovides examples of how the module is accessed by the applicationsoft
4Ć2The frequency with which tasks, or application programs, read theirinputs and write their outputs depends on the language being used.Ladder logic a
1 !"* *+"'& /($"&* !'. +' +)',$*!''+ +! %',$ &
5Ć2WARNINGBE CAREFUL WHEN WRITING TO THE OUTPUTS TO INSURE THAT NOUNEXPECTED MACHINE MOTION WILL RESULT. FAILURE TO OBSERVE THISPRECAUTION COULD RESUL
5Ć35.2 Bus ErrorProblem: A 31" or 51" through 58" appears on the processormodule's LED. This error message indicates that there
Copyright Reliance Electric Industrial Company 1991.Reliance is a trademark of Reliance Electric Companyąąor its subsidiariesThe information in thi
fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd
AĆ1Appendix ATechnical SpecificationsAmbient ConditionsD Storage temperature: -40_ CĆ85_ CD Operating temperature: 0_ CĆ60_ CD Humidity: 5Ć90% nonĆcon
fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd
BĆ1 115 AC/DC LOW OUTPUT MODULE (57C402)ADDRESSDECODERADDRESSID BUSBUSBUSADDRESSBUSADDRESSWDOG OKCONTROLLOGICBD RESETINIT
fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd
Appendix CField ConnectionsTerminal BoardNumberReg. 0Bit
fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd
DĆ1 57C370 - Terminal Strip/Cable AssemblyThis assembly consists of a terminal strip, cable, and mating connector.It is use
fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd
EĆ1 This section describes how to configure the output module when it is locat
ITable of Contents1.0 Introduction 1Ć1...2.0 Mechanical/Electrical Description 2Ć1...
EĆ2 Use the following method to reference the entire module as a single register. Onlyone statement is required in the configu
EĆ3 This section describes how to configure the output module when it is located in arack that is remote from the processor module
EĆ4Single Register ReferenceUse the following method to reference the entire module as a single register. Onlyone statement is required in the configu
fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd
For additional information1 Allen-Bradley DriveMayfield Heights, Ohio 44124 USATel: (800) 241-2886 or (440) 646-3599http://www.reliance.com/automaxCop
! # " #
III Figure 2.1 Ć Typical Output Circuit 2Ć1...Figure 2.2 Ć Module Faceplate 2Ć2...
fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd
1Ć1 The products described in this instruction manual are manufacturedor distributed by Reliance Electric Company or its subsidiaries.T
fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd
2Ć1 The following is a description of the faceplate LEDs, field terminationconnectors, and electrical characteristi
Comentarios a estos manuales