Rockwell-automation 8510 Hardware/Firmware Replacement Instructions Manual de usuario descargar pdf (Pagina 1)

ALLEN-BRADLEY

Instructions

8510 AC Spindle Drive

Hardware/Firmware Replacement

Introduction The purpose of this publication is to describe the steps needed to replace

the circuit boards and/or firmware in the 8510 AC Spindle Drive.

Replacement Procedure Different procedures are provided in this publication to guide the user in

the removal and replacement of the various boards and firmware in the

8510. Refer to the appropriate section(s) to remove/replace the supplied

boards/firmware.

Important: When replacing the I/O and/or Main Control/CPU Boards,

always remove the existing firmware chips (EPROM/EEPROM) for

possible use in the new boards.

ATTENTION: The circuit boards included in this kit are ESD

(Electrostatic Discharge) sensitive. In addition, the drive also

contains ESD sensitive parts and assemblies. Static control

precautions are required when installing, testing, servicing or

repairing this assembly. Component damage may result if ESD

control procedures are not followed. If you are not familiar with

static control procedures, reference Allen-Bradley publication

8000-4.5.2, Guarding Against Electrostatic Damage or any

other applicable ESD Protection Handbook.

ATTENTION: To avoid an electrical shock hazard, assure that

all power to the drive has been removed and that 30 seconds has

elapsed (for bus discharge) prior to proceeding.

A disposable grounding wrist strap is included with the replacement parts

kit. This strap must be worn to guard against ESD damage to the drive or

its components. Apply the strap around your wrist – affix the other end to

the drive chassis (bare metal).

The following tools are recommended:

- IC Chip Puller

- #0 and #2 Phillips Screwdriver

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Hardware/Firmware Replacement

ALLEN-BRADLEYInstructions8510 AC Spindle DriveHardware/Firmware ReplacementIntroduction The purpose of this publication is to describe the steps neede

Pagina 2 - Instructions

8510 Hardware/Firmware ReplacementInstructions2o 1. Display & Keypad Module Replacementa) Assure that all power has been removed and 30 seconds ha

Pagina 3

8510 Hardware/Firmware ReplacementInstructions3o 2. I/O Board Replacementa) Assure that all power has been removed and 30 seconds has elapsed.b) Remov

Pagina 4

8510 Hardware/Firmware ReplacementInstructions4o 3. Main Control/CPU Board Replacementa) Assure that all power has been removed and 30 seconds has ela

Pagina 5 - Component Locations

8510 Hardware/Firmware ReplacementInstructions5Figure 1Component LocationsCN2EPROMBAZGND8510A-A04, A06 CPU BoardCN9 CN10EEPROMContrastBrightnessANAOUT

Pagina 6

8510 Hardware/Firmware ReplacementInstructions6o 4. Gate Drive Board Replacement (8510A-A04/A06 Only)a) Assure that all power has been removed and 30

Pagina 7

8510 Hardware/Firmware ReplacementInstructions7o 5. Firmware ReplacementThe control firmware for the 8510 is contained in two IC packages, ontwo print

Pagina 8

8510 Hardware/Firmware ReplacementInstructions8i) Noting notch orientation (notch on IC must align with notch onsocket), insert the new package into t

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 8510 Hardware/Firmware Replacement Instructions Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Equipo Rockwell-automation 8510 Hardware/Firmware Replacement Instructions. Rockwell Automation 8510 Hardware/Firmware Replacement Instructions User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Rockwell-automation 8510 Hardware/Firmware Replacement Instructions Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Equipo Rockwell-automation 8510 Hardware/Firmware Replacement Instructions. Rockwell Automation 8510 Hardware/Firmware Replacement Instructions User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 8510 Hardware/Firmware Replacement Instructions