Rockwell Automation 22-WIM-N4S Especificaciones descargar pdf (Pagina 20)

PARAMETERS

No. Name Description

01 Config Mode Displays the module’s configuration mode.

02 DSI Mode Displays the module’s operating mode (single or multi-drive).

03 Reset Module Used to reset the module or set defaults.

04 Idle Action 1 Sets the action that the module and CH1 drive take if the module

detects that the controller was switched to Program mode or Test mode.

05 Flt Cfg Logic 1 Sets the data that is sent to the CH1 drive if Parameter 04 - [Idle Action 1]

06 Flt Cfg Ref 1

is set to “Send Flt Cfg” and the controller is put into Program or Test mode.

07 DSI I/O Cfg 1 Sets the configuration of the CH1 drives that are active in the Multi-drive mode.

08 DSI I/O Act 1 Displays the CH1 drives that are active in the Multi-drive mode.

09 Drv 0 Addr 1 Sets the corresponding node addresses of the daisy- chained CH1 drives when

10 Drv 1 Addr 1

the module Operating Mode Switch (SW2) is set for Multi-drive operation.

11 Drv 2 Addr 1

12 Drv 3 Addr 1

13 Drv 4 Addr 1

14 RTU Baud Rate 1 Sets the baud rate used by the CH1 drives when the module is operating in the

Multi-drive mode and Parameter 07 - [DSI I/O Cfg 1] is set to “RTU Master”.

15 RTU Parity 1 Sets the parity used by the CH1 drives when the module is operating in the

Multi-drive mode and Parameter 07 - [DSI I/O Cfg 1] is set to “RTU Master”.

16 RTU Rx Delay 1 Sets the inter-character delay used by the CH1 drives to detect the end

of a receive packet when the module is operating in the Multi-drive

mode and Parameter 07 - [DSI I/O Cfg 1] is set to “RTU Master”.

17 RTU Tx Delay 1 Sets the inter-frame delay used by the CH1 drives to delay the sending of

a transmit packet when the module is operating in the Multi-drive mode

and Parameter 07 - [DSI I/O Cfg 1] is set to “RTU Master”.

18 RTU MsgTimeout 1 Sets the amount of time in seconds that the module will wait for a

response from a Modbus RTU CH1 slave when the module is operating in the

Multi-drive mode and Parameter 07 - [DSI I/O Cfg 1] is set to “RTU Master”.

19 Idle Action 2 Sets the action that the module and CH2 drive take if the module detects

that the controller was switched to Program mode or Test mode.

20 Flt Cfg Logic 2 Sets the data that is sent to the CH2 drive if Parameter 19 - [Idle Action 2]

21 Flt Cfg Ref 2

is set to “Send Flt Cfg” and the controller is put into Program or Test mode.

22 DSI I/O Cfg 2 Sets the configuration of the CH2 drives that are active in the Multi-drive mode.

23 DSI I/O Act 2 Displays the CH2 drives that are active in the Multi-drive mode.

24 Drv 0 Addr 2 Sets the corresponding node addresses of the daisy- chained CH2 drives when

25 Drv 1 Addr 2

the module Operating Mode Switch (SW2) is set for Multi-drive operation.

26 Drv 2 Addr 2

27 Drv 3 Addr 2

28 Drv 4 Addr 2

29 RTU Baud Rate 2 Sets the baud rate used by the CH2 drives when the module is operating in the

Multi-drive mode and Parameter 22 - [DSI I/O Cfg 2] is set to “RTU Master”.

30 RTU Parity 2 Sets the parity used by the CH2 drives when the module is operating in the

Multi-drive mode and Parameter 22 - [DSI I/O Cfg 2] is set to “RTU Master”.

31 RTU Rx Delay 2 Sets the inter-character delay used by the CH2 drives to detect the end of a

receive packet when the module is operating in the Multi-drive mode and

Parameter 22 - [DSI I/O Cfg 2] is set to “RTU Master”.

32 RTU Tx Delay 2 Sets the inter-frame delay used by the CH2 drives to delay the sending of a

transmit packet when the module is operating in the Multi-drive mode and

Parameter 22 - [DSI I/O Cfg 2] is set to “RTU Master”.

33 RTU MsgTimeout 2 Sets the amount of time in seconds that the module will wait for a response

from a Modbus RTU CH2 slave when the module is operating in the Multi-drive

mode and Parameter 22 - [DSI I/O Cfg 2] is set to “RTU Master”.

34 Idle Action 3 Sets the action that the module and CH3 drive take if the module detects

that the controller was switched to Program mode or Test mode.

35 Flt Cfg Logic 3 Sets the data that is sent to the CH3 drive if Parameter 34 - [Idle Action 3] is set

36 Flt Cfg Ref 3

to “Send Flt Cfg” and the controller is put into Program or Test mode.

37 DSI I/O Cfg 3 Sets the configuration of the CH3 drives that are active in the Multi-drive mode.

38 DSI I/O Act 3 Displays the CH3 drives that are active in the Multi-drive mode.

39 Drv 0 Addr 3 Sets the corresponding node addresses of the daisy-chained CH3 drives when the module

40 Drv 1 Addr 3

Operating Mode Switch (SW2) is set for Multi-drive operation.

41 Drv 2 Addr 3

42 Drv 3 Addr 3

43 Drv 4 Addr 3

44 RTU Baud Rate 3 Sets the baud rate used by the CH3 drives when the module is operating in the

Multi-drive mode and Parameter 37 - [DSI I/O Cfg 3] is set to “RTU Master”.

45 RTU Parity 3 Sets the parity used by the CH3 drives when the module is operating in the

Multi-drive mode and Parameter 37 - [DSI I/O Cfg 3] is set to “RTU Master”.

46 RTU Rx Delay 3 Sets the inter-character delay used by the CH3 drives to detect the end of a

receive packet when the module is operating in the Multi-drive mode and

Parameter 37 - [DSI I/O Cfg 3] is set to “RTU Master”.

47 RTU Tx Delay 3 Sets the inter-frame delay used by the CH3 drives to delay the sending of a

transmit packet when the module is operating in the Multi-drive mode and

Parameter 37 - [DSI I/O Cfg 3] is set to “RTU Master”.

48 RTU MsgTimeout 3 Sets the amount of time in seconds that the module will wait for a response

from a Modbus RTU CH3 slave when the module is operating in the Multi-drive

mode and Parameter 37 - [DSI I/O Cfg 3] is set to “RTU Master”.

SPECIFICATIONS

Communications Network Protocol DSI/Modbus RTU

Data Rates DSI: 19.2 Kbps

Modbus RTU: 300 - 38400 bps

Electrical Consumption Module 350 mA at 5 VDC

Channel 0 mA at 24 VDC (supplied by

Compact I/O power supply)

Regulatory UL UL508C

Compliance cUL CAN/CSA C22.2 No. 14-M91

CE EN50081-2 and EN61000-6-2

CTick AS/NZS 2064, 1997, Group 1, Class A

EXAMPLE I/O IMAGE

Single-Drive Mode

Multi-Drive Mode

Word

Output Image Input Image CH1 CH2 CH3

Module Control Word Module Status Word 0

Logic Command Logic Status 1 3 5

Speed Reference Speed Feedback 2 4 6

Word

Output Image Input Image

CH1 CH2 CH3

Module Control Word Module Status Word 0

Drive 0

Logic Command Logic Status 1 11 21

Speed Reference Speed Feedback 2 12 22

Drive 1

Logic Command Logic Status 3 13 23

Speed Reference Speed Feedback 4 14 24

Drive 2

Logic Command Logic Status 5 15 25

Speed Reference Speed Feedback 6 16 26

Drive 3

Logic Command Logic Status 7 17 27

Speed Reference Speed Feedback 8 18 28

Drive 4

Logic Command Logic Status 9 19 29

Speed Reference Speed Feedback 10 20 30

1769-SM2_PP_NL_9_28.qxd:Product_app_profile5-18-05.qxd 9/28/06 7:39 AM Page 2

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 29 30

Comentarios a estos manuales

Sin comentarios

Rockwell Automation 22-WIM-N4S Especificaciones Pagina 20

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Rockwell Automation 22-WIM-N4S