Rockwell-automation 1336S_F_T_E_R C-Frame Front End Conversion Kit Manual de usuario descargar pdf (Pagina 3)

1336 PLUS, PLUSII, IMPACT, and FORCE C-Frame Front End Conversion Kit 3

Fastener Torque

Speciﬁcations

Fastener Torque Speciﬁcations are listed in Table A.

Table A Fastener Torque Speciﬁcations

Instructions

1. Back-up the programming of the drive being converted before

proceeding:

– Store the programming of the drive in the HIM (if applicable to your

HIM) or

– Use Drive Tools, Drive Explorer, or Drive Explorer Light to back-up

the programming of the drive.

2. Remove and lock out the line power from the existing C-frame drive that

will be converted.

3. For disassembly instructions, refer to Chapter 3 in the Troubleshooting

Guide. The 1336-CONVCF-SPxA Kit is shown in

Figure 1 on page 5.

4. An illustration of the CONVCF Kit with numbered cables and wires is

shown in

Figure 2 on page 6. The cables have the destination connector

number on them.

5. For assembly instructions refer to Chapter 3 in the Troubleshooting

Guide.

6. Re-connect the power and control wiring. Torque specs are listed in

Table A.

Component Fastener Application Torque lb-in. Torque N-m

Main Control Board Mounting Plate 8 – 10 0.9 – 1.1

Gate Driver Board Mounting Plate 8 – 10 0.9 – 1.1

Precharge Board Mounting Plate 8 – 10 0.9 – 1.1

Bus Capacitor Bank Bank to chassis 25 – 31 2.8 – 3.5

DC Bus Inductor Wires to bus bars 25 – 31 2.8 – 3.5

DC Bus Inductor TB1 mounting plate to chassis 25 – 31 2.8 – 3.5

Snubber Board Bus bars to capacitor bank 25 – 31 2.8 – 3.5

Snubber Board Board to SCR1 25 – 31 2.8 – 3.5

Snubber Board Board to PM1 – PM3 30 – 39 3.4 – 4.4

Power Modules PM1 – PM3 Module to heat sink 25 – 31 2.8 – 3.5

Input Rectiﬁer Rectiﬁer to heat sink 25 – 31 2.8 – 3.5

Bus Fuse F1 Fuse to chassis 200 – 220 22.6 – 24.8

Thermistor Thermistor to heat sink Hand tighten only

TB1 Wires to terminals 25 – 31 2.8 – 3.5

TB2 Wires to terminals 8 0.9

TB3 Wires to terminals 8 0.9

Ground Sense CT Bracket to chassis 25 – 31 2.8 – 3.5

Ground Sense CT Positive bus bar junction 25 – 31 2.8 – 3.5

Ground Sense CT Bus bars to capacitor bank 25 – 31 2.8 – 3.5

ATTENTION: Make sure the two shorting devices

shown in

Figure 3 on page 6 are removed before

connecting into J7 and J8 of the Gate Driver Board.

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 1336S_F_T_E_R C-Frame Front End Conversion Kit Manual de usuario Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 1336S_F_T_E_R C-Frame Front End Conversion Kit