Rockwell-automation 150 SMC-Flex User Manual Manual de usuario Pagina 17
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Product Overview 1-9
Modes of Operation
(Braking Control)
SMB™ Smart Motor Braking Option
This option can be used in applications that require reduced stopping
times. The SMC-Flex controller incorporates a microprocessor-based
system that applies braking current to a motor without any additional
equipment. This option offers a user-adjustable braking current
setting from 0% to 400% of the motor’s full load current rating.
Further, it provides automatic shut-off at zero speed detection.
Figure 1.10 SMB Smart Motor Braking Option
Note: All braking current settings in the range of 1…100% will
provide 100% braking current to the motor.
100%
Motor Speed
Smart Motor
Braking
Coast-to-Rest
Time in Seconds
Automatic Zero
Speed Shut-Off
Start
Run
Brake
Stop
Time
ATTENTION
!
SMB Smart Motor Braking is not intended to be used
as an emergency stop. Refer to applicable standards
for emergency stop requirements.
- USER MANUAL FOR SERIES B 1
- Important User Information 2
- European Communities (EC) 3
- Directive Compliance 3
- Table of Contents 5
- Chapter 3 6
- Chapter 4 6
- Programming 6
- 625…1250 A units 8
- Product Overview 9
- Ramp Time 10
- Selectable Kickstart 11
- Current Limit Start 11
- Dual Ramp Start 12
- Full Voltage Start 12
- Preset Slow Speed 13
- Linear Speed Acceleration 14
- Soft Stop 15
- Modes of Operation 16
- (Pump Control) 16
- (Braking Control) 17
- Accu-Stop™ Option 18
- Overload 19
- Underload 19
- 1-12 Product Overview 20
- Undervoltage 21
- Overvoltage 21
- Unbalance 21
- Figure 1.15 Stall Protection 22
- Figure 1.16 Jam Detection 22
- Ground Fault 23
- 1-16 Product Overview 24
- Thermistor/PTC Protection 25
- Excessive Starts/Hour 26
- Overtemperature 26
- Open Gate 26
- Line Faults 26
- Product Overview 1-19 27
- Figure 1.19 DPI Location 28
- Figure 1.21 Control Terminals 29
- 1-22 Product Overview 30
- Installation 31
- Lifting Points 32
- Installation 2-3 33
- 2-4 Installation 34
- Installation 2-5 35
- Power Factor 42
- Correction Capacitors 42
- Motor Overload 43
- Protection 43
- Enclosure 44
- Additional Requirements 44
- Power Wiring 47
- Line Connected 48
- Delta Connected 48
- Wiring 3-5 49
- Control Power Control Wiring 51
- GENERAL NOTES: 52
- Wiring 3-9 53
- 625…1250 A Devices 54
- Control Wire Specifications 55
- Fan Terminations 55
- Standard Controller Wiring 57
- Diagrams 57
- Control (No DPI Control) 58
- Wiring 3-15 59
- Wiring 3-17 61
- 3-18 Wiring 62
- Wiring 3-19 63
- 3-20 Wiring 64
- Wiring 3-21 65
- 3-22 Wiring 66
- SMC-Flex 67
- Control Terminals 67
- Soft Stop, Pump Control, and 68
- SMB Smart Motor Braking 68
- Wiring 3-27 71
- Wiring 3-29 73
- 3-#&LEX 74
- #ONTROL4ERMINALS 74
- Wiring 3-31 75
- 3-32 Wiring 76
- ATTENTION 77
- 3-36 Wiring 80
- PROTECTIVE MODULE 81
- MAX. LINE VOLTAGE 81
- 3-38 Wiring 82
- Wiring 3-39 83
- 1410 Motor Winding Heater 84
- ➁ Steps back one level 86
- Programming 4-3 87
- 0.0 Amps 89
- EEPROM RAM ROM 90
- Memory Storage: 90
- Reset to Defaults 90
- Input (Dual Ramp) 93
- Pump Control 96
- Braking Control 96
- 4-14 Programming 98
- Parameter Option 98
- Undervoltage ➀ 100
- Overvoltage ➀ 100
- Underload ➁ 100
- Chapter 5 101
- Preferences 102
- Optional HIM Operation 103
- Communications 105
- Keypad Description 106
- Communications 7-3 107
- HIM Control Enable 108
- Communications 7-5 109
- Loss of Communication and 110
- Network Faults 110
- Variable Input/Output 111
- Configuration 111
- SMC — Flex Bit Identification 112
- Scale Factors for PLC 113
- Communication 113
- Rules for Using DataLinks 114
- Diagnostics 115
- 8-2 Diagnostics 116
- Fault and Alarm Auxiliary 117
- Indication for Fault or Alarm 117
- Table 8.B Fault Definitions 118
- Troubleshooting 119
- Prestart fault indication 122
- Troubleshooting 9-7 125
- 9-8 Troubleshooting 126
- Appendix A 127
- Specifications 127
- Electrical Ratings 128
- Short Circuit Protection 129
- Environmental 131
- Mechanical 131
- Approximate Dimensions and 132
- Shipping Weights 132
- Parameter Information 135
- ➂ Sec 0…999 0 138
- ➂ % current 0…37 0 145
- B-14 Parameter Information 148
- Renewal Parts 149
- C-2 Renewal Parts 150
- Appendix D 151
- Accessories 155
- E-2 Accessories 156
- Renewal Part Cross Reference 157
- Appendix C 158
Relacionado con productos y manuales para Equipo Rockwell-automation 150 SMC-Flex User Manual
Equipo Rockwell-automation 440N-Z2NRS1A_Z2NRS1B_Z2NRS1C Magnetically Coded No Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 198E-C0S4R Plastic Encl. for DOL and Reversing Sta Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 25B PowerFlex 520-Series Control & Power Modul Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 140U J-Frame CB and Motor Circuit Protectors Therm Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 150-SCMRTB SMC-50 Soft Starter Control Module Term Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales