Rockwell-automation 1771-IR Series D RTD Input Module User Manual Manual de usuario Pagina 67
- Pagina / 79
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2 and 4–Wire RTD Sensors E–3
,$#+#'& / )"
The illustration below shows how to connect 4–wire sensors to the
field wiring arm of the RTD Input module. A 4–wire sensor has two
pairs of leads; one pair for each resistor junction. One wire of the 4 is
not used (it does not matter which one). This leaves 3 wires – one
pair and one single wire. You must connect the single wire to the
terminal marked ”A”. You connect the remaining pair of wires to
terminals ”B” and ”C”. It doesn’t matter which wire of the pair
connects to terminal ”B” and which wire connects to terminal ”C” so
long as all 3 wires are the same AWG gauge.
Connecting a 4–Wire Sensor to the Field Wiring Arm
)',&
"&&$
"&&$
"&&$
"&&$
"&&$
"&&$
)%#&$
&+# #+#'&
"**#*
- $ '(&
#&!$ $ '&&+* +' +)%#&$
Note: & +"#* #$$,*+)+#'&
)%#&$ #* +" % .#++#'& *',)#&! ,))&+
)%#&$ #* +" $ '%(&*+#'& *&* #&(,+
)%#&$ #* '%%'&
Connecting 4-Wire
Sensors
- 1
- 1
- Important User Information 2
- 3
- Related Products 4
- Product Compatibility 4
- Related Publications 5
- Using This ManualP–4 6
- Table of Contents 7
- Configuring Your RTD 8
- Module Status and Input 8
- Calibrating Your Module 8
- Table of Contents toc-iii 9
- Table of Contents 10
- Overview of the RTD Input 11
- How Analog Modules 12
- Communicate with 12
- Programmable Controllers 12
- Accuracy 13
- Chapter Summary 13
- Installing the RTD Input 15
- Calculate Power 16
- Requirements 16
- Determine Module 16
- Placement in the I/O 16
- Key the Backplane 17
- Connector 17
- Install the Module and 17
- Field Wiring Arm 17
- Connect Wiring to the 18
- Ground the Chassis and Module 20
- Interpret Status Indicators 21
- 23
- PLC-2 Program Example 24
- Program Action 25
- PLC-3 Program Example 26
- PLC-5 Program Example 27
- Module Scan Time 28
- Configuring Your RTD Module 29
- Data Format 30
- RTD Type 30
- Units of Measure 30
- Real Time Sampling 31
- Configuring Block for a 32
- Block Transfer Write 32
- Bit/Word Descriptions 32
- calibration complete 34
- Module Status and Input Data 35
- 39
- Performing 40
- Auto-calibration 40
- Gain Calibration 42
- Performing Manual 43
- Calibration 43
- Refer to the table below 44
- Calibration 45
- 47
- (1771-IR/D) 48
- 7–4 Troubleshooting 50
- 51
- 53
- PLC-3 Family Processors 54
- PLC-5 Family Processors 55
- Programming ExamplesB–4 56
- 57
- Signed-magnitude Binary 58
- Two's Complement Binary 59
- Data Table FormatsC–4 60
- Block Transfer (Mini-PLC-2 61
- Setting the Block Length 63
- (Multiple GET Instructions 63
- 2 and 4-Wire RTD Sensors 65
- 2 and 4–Wire RTD SensorsE–2 66
- Connecting 4-Wire 67
- 2 and 4–Wire RTD SensorsE–4 68
- Differences Between Series A 69
- RTD Modules and Series B. C 69
- CSA Hazardous Location 73
- Approval 73
- AllenĆBradley 77
- Publication Problem Report 77
- BUSINESS REPLY MAIL 78
- Worldwide representation 79
Relacionado con productos y manuales para Equipo Rockwell-automation 1771-IR Series D RTD Input Module User Manual
Equipo Rockwell-automation 1757-SWKIT4000 ProcessLogix R400.0 Installation an Manual de usuario
(293 paginas)
(293 paginas)
Equipo Rockwell-automation 1732E-IR4IM12R ArmorBlock Dual-Port EtherNet/IP 4- Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1747-C13 Instruction Sheet for Catalog No. 1747-C1 Manual de usuario
(1 paginas)
(1 paginas)
Equipo Rockwell-automation 1769-IM12 Compact 1769-IM12 240Vdc Input Module Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1784-PCM2/B CABLE Installation Instructions Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1771-OQ16/C Isolated Output Module Installation In Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1747-SCNR SLC ControlNet Scanner Module Installati Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1788-CN2DN ControlNet-to-DeviceNet Linking Device Manual de usuario
(52 paginas)
(52 paginas)
Equipo Rockwell-automation 1794-ADN/C, 1794-ADNK/C FLEX I/O DeviceNet Adapter Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 1746-QV,D17466.18 OPEN-LOOP VELOCITY CONTL Manual de usuario
(35 paginas)
(35 paginas)
Equipo Rockwell-automation 1746-BTM Barrel Temperature Control Module User Ma Manual de usuario
(84 paginas)
(84 paginas)
Equipo Rockwell-automation 1764-DAT MicroLogix 1500 Data Access Tool Installa Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales