Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog Manual de usuario Pagina 96
- Pagina / 164
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Publication 1794-UM065B-EN-E - September 2010
84 Configure Module Messaging
Get Device Info Block 2 Message
Get Device Information Block 2 Message – Request Packet Structure
Field Value Definition
Message Type "CIP Generic"
Service Type Get Attribute Single Read From Module
Service Code 0x0E
Class Name 0x7D FLEX Module Object
Instance 1…8 (Module next to Adapter = 1) Module Location
Object Attribute 0x88 = Channel 0 (Add 4 for next channel)
0x8C = Channel 1
0x90 = Channel 2
0x94 = Channel 3
0x98 = Channel 4
0x9C = Channel 5
0xA0 = Channel 6
0xA4 = Channel 7
Selects Channel that the
data is from
Reply Size 56 bytes
Request Size 0
Get Device Information Block 2 Message – Reply Packet Structure
Offset
(1)
(1)
Data in offsets 2…55 will be set to 0 if Status in offset 0 indicates a problem (Status = 0x86 or 0x87).
Field Value Definition
0 Status 00 = SUCCESS
0x86 = Channel is not
HART Enabled
0x87 = No Device
Found
Command status
1 Echo of Channel 0…7 Channel
2 TransferFunction (1 byte) CMD#15, Byte 1
3 WriteProtectCode (1 byte) CMD#15, Byte 15
4…7 MessageSize (4 bytes)
8…39 MessageString (32 bytes unpacked
ASCII)
CMD#12, Bytes 0…23
40…43 HARTPVUpperRange (4 bytes - UINT) CMD#15, Bytes 3…6
44…47 HARTPVLowerRange (4 bytes - UINT) CMD#15, Bytes 7…10
48…51 DampingValue (4 bytes - UINT) CMD#15, Bytes 11…14
52…55 FinalAssemblyNumber (4 bytes - UINT) CMD#16, Bytes 0…2
Bytes re-ordered into Intel
Format (LSB 1st) from HART
Format (MSB 1st)
- Analog Modules 1
- Important User Information 2
- Summary of Changes 3
- Related Documentation 5
- Table of Contents 7
- 1794-IF8IH and 1794-OF8IH 8
- Table of Contents iii 9
- Table of Contents v 11
- What FLEX I/O Analog 13
- Modules Do 13
- Communicate with 14
- Programmable Controllers 14
- Physical Features of 15
- Your Module 15
- Use Alarms on the Input 15
- Overrange Alarm 16
- Underrange Alarm 16
- Remote Fault Alarm 16
- Local Fault Alarm 17
- Use the HART Capabilities 18
- HART Implementation 18
- Features 19
- Select Your Analog Input 20
- Module Operating Features 20
- Data Format 21
- Select Your Analog Output 22
- Latch Mode 23
- Global Reset 23
- Diagnostic Data error 11 24
- = data out of range 24
- Understand Image Table 25
- Mapping and Bit/Word 25
- Descriptions 25
- ATTENTION 27
- Install the Module 28
- Mount on a Panel or Wall 30
- Description Description 31
- IMPORTANT 32
- Label here 33
- Wire the Terminal Base 34
- Connect Wiring to the FLEX 34
- I/O HART Analog Modules 34
- Terminal Base Unit 35
- Ground the Module 36
- Use Programming Software 37
- About the ControlNet and 38
- EtherNet Adapters 38
- Communication Over the 38
- FLEX I/O Backplane 38
- Scheduled Data Transfer 39
- Unscheduled Data Transfer 39
- Module I/O Mapping 39
- I/O Structure 40
- Fault State Data 40
- Device Actions 40
- Data Transfer Types 43
- Configuration Parameters 44
- Byte Order (2 of 2 bits) 47
- Examples 49
- Fault Mode (8 of 1 bit) 50
- Low Alarm Limit (8 of 16 bit) 54
- Real Time Data (RTD) 57
- Profile, Primary Input 57
- Parameters 57
- Profile, Primary Status 58
- High Alarm (8 of 1 bit each) 60
- Low Alarm (8 of 1 bit each) 60
- Loop Alarm (8 of 1 bit each) 61
- HART Status Fields 63
- Secondary Input Data 64
- Table, Cyclic EDT Input 64
- HART PV Status (8 of 8 bits): 67
- Bit 5 Reserved 68
- Bit 6 Reserved 68
- Bit 7 Reserved 68
- HART PV Status 68
- Interpret the Status 69
- Indicators 69
- Module Configuration for 69
- Little Endian Byte Order 75
- Word Swap BYTE ORDER 75
- Profile, Status Parameters 82
- Fault Alarm (8 of 1 bit each) 83
- Diagnostic Data (1 of 8 bits) 83
- Profile, Output Parameters 85
- Global Reset (1 of 1 bit) 86
- Status Indicators 87
- Configure Module Messaging 89
- HART Configuration Quick 90
- Field Value Definition 100
- HART Failed Reason Code 104
- Chapter Summary 106
- Troubleshoot Your Module 107
- FLEX I/O HART Module Commands 109
- Commands 110
- Universal Commands 110
- Common Practice 110
- Device-specific Commands 111
- Appendix 113
- Overview 113
- Message Structure 113
- Burst Mode (not supported) 114
- Start Character 115
- HART Address 115
- HART Command 115
- Byte Count 116
- Check Byte 116
- Response Code 116
- Communication 127
- HART Frame Enhancements 130
- Background Information 131
- Configuration 132
- HART Disable 133
- Channel Data Format 133
- Channel Data Formats 134
- Digital Filters 135
- High Alarm Limit 138
- Low Alarm Limit 138
- Remote High High Alarm Limit 138
- Input Map 139
- High Alarm 140
- Low Alarm 140
- Out of Range 141
- Second Alarm 141
- Diagnostic Status 141
- HART Fault 142
- HART Current Fault 142
- HART Transmitter Present 143
- Local Fault Mode 147
- Digital Mode 152
- Digital Fault Mode 153
- Analog Fault Value 153
- HART Command 3 Disable 153
- Digital Data 154
- Fault Reset 154
- Analog Data 154
- 152 Index 160
- How Are We Doing? 161
- BUSINESS REPLY MAIL 162
- Rockwell Automation 164
Relacionado con productos y manuales para Equipo Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog
Equipo Rockwell-automation 2090-K2KSCLAMP-4 Kinetix 2000 Cable Clamp Bracket Manual de usuario
(4 paginas)
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2707-M232P3_M485P3 DTAM Micro Operator Interface M Manual de usuario
(124 paginas)
(124 paginas)
Equipo Rockwell-automation 57C329 Remote I/O Communications, AutoMax Manual de usuario
(144 paginas)
(144 paginas)
Equipo Rockwell-automation 6189x Integrated Display Industrial Computers User Manual de usuario
(124 paginas)
(124 paginas)
Equipo Rockwell-automation 4100 REC Resolver to Encoder Converter Installatio Manual de usuario
(50 paginas)
(50 paginas)
Equipo Rockwell-automation 2097-Rx Shunt Resistor Installation Instructions Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 4100 ESRS Encoder Signal Reference Simulator Insta Manual de usuario
(37 paginas)
(37 paginas)
Equipo Rockwell-automation 9528-APPOWSENE Virtual Image Templates User Manual Manual de usuario
(120 paginas)
(120 paginas)
Equipo Rockwell-automation 1798-DFTP2 FlexArmor DeviceNet Field Termination P Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 2090 Ultra3000 Servo Drives Integration Manual Manual de usuario
(180 paginas)
(180 paginas)
Equipo Rockwell-automation 6181F_P Series E Integrated Display Computers Inst Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales