Rockwell-automation 20D-RES-A0 PowerFlex 700S Resolver Feedback Option Manual de usuario descargar pdf

Installation Instructions

Resolver Feedback Option Card for PowerFlex

700S Drives

What This Kit Contains

Verify that your kit contains the items listed in the following table. If your

kit does not contain the correct items, contact your Allen-Bradley sales

representative.

Tools That You Need

• Phillips

screwdriver for M3 screws

• Pozidrive

screwdriver for M4 screws (for high power drives only)

• Nut driver or wrench for M3 hex nut

• Nut driver or wrench for M5 hex nut

Important: The Resolver Feedback Option requires Phase I drive firmware

to be revision 1.17 or higher (All revsions of Phase II drive

firmware support this option).

Important: You must cycle power to the drive after making changes to

parameter 275 [Reslvr0 Select] (on a Phase I drive) or 277

[Reslvr0 Select] (on a Phase II drive), for the changes to take

affect.

ATTENTION: To avoid an electric shock hazard, verify that the

voltage on the bus capacitors has discharged before performing

any work on the drive. Measure the DC bus voltage at the +DC &

–DC terminals of the Power Terminal Block (DC+ & DC- in high

power drives). The voltage must be zero.

ATTENTION: HOT surfaces can cause severe burns. Do not

touch the heatsink surface during operation of the drive. After

disconnecting power allow time for cooling.

ATTENTION: This drive contains ESD (Electrostatic

Discharge) sensitive parts and assemblies. Static control

precautions are required when installing, testing, servicing or

repairing this assembly. Component damage may result if ESD

control procedures are not followed. If you are not familiar with

static control procedures, reference A-B publication 8000-4.5.2,

“Guarding Against Electrostatic Damage” or any other

applicable ESD protection handbook.

Quantity: Description

1 Resolver Feedback Option circuit board

2 “Stacker” connectors

3 Screws with captive lock washers

3 Stand-offs

1 2 3 4 5 6 ... 15 16

Indice de contenidos

Pagina 1 - 700S Drives

Installation InstructionsResolver Feedback Option Card for PowerFlex® 700S DrivesWhat This Kit ContainsVerify that your kit contains the items list

Pagina 2 - What You Need to Do

10 Resolver Feedback Option Card for PowerFlex® 700S Drives Step 7: Installing Cover(s)Important: The procedure for installing covers on Frame 9 dri

Pagina 3 - (if necessary) Phase I Drives

Resolver Feedback Option Card for PowerFlex® 700S Drives 11 Step 8: Documenting Revision ChangesDocument drive revisions on the “Field Installed Opt

Pagina 4 - Phase II Drives

12 Resolver Feedback Option Card for PowerFlex® 700S Drives SpecificationsResolver Feedback Option Card SpecificationsCompatible ResolversTable A sp

Pagina 5 - Feedback Option Card

Resolver Feedback Option Card for PowerFlex® 700S Drives 13 Allen-Bradley servo motors may be ordered with factory installed resolvers. Table B spec

Pagina 6 - Phase I Drives

14 Resolver Feedback Option Card for PowerFlex® 700S Drives Recommended CableRockwell Automation strongly recommends the use of Reliance Electric 41

Pagina 7

Resolver Feedback Option Card for PowerFlex® 700S Drives 15 Notes:

Pagina 8 - 12345 6 78

Pagina 9 - Connection Examples

2 Resolver Feedback Option Card for PowerFlex® 700S Drives What You Need to DoTo remove the resolver option board from the PowerFlex 700S drive:❐ St

Pagina 10 - Step 7: Installing Cover(s)

Resolver Feedback Option Card for PowerFlex® 700S Drives 3 Step 1: Removing Cover(s) (if necessary) Phase I DrivesEsc7 8 94 5 61 2 3.0 +/-SelJogAltE

Pagina 11 - Revision Changes

4 Resolver Feedback Option Card for PowerFlex® 700S Drives Step 1: Removing Cover(s) Phase II DrivesIt is necessary to remove the cassette from the

Pagina 12 - Specifications

Resolver Feedback Option Card for PowerFlex® 700S Drives 5 Step 2: Removing the Control Assembly (if necessary)This step is necessary only when anot

Pagina 13

6 Resolver Feedback Option Card for PowerFlex® 700S Drives Step 4: Installing the Feedback Option Card Phase I DrivesImportant: Do not use a screwdr

Pagina 14 - Recommended Cable

Resolver Feedback Option Card for PowerFlex® 700S Drives 7 Step 4: Installing the Feedback Option Card Phase II DrivesImportant: Do not use a screwd

Pagina 15

8 Resolver Feedback Option Card for PowerFlex® 700S Drives Step 6: Wiring the Resolver Feedback Option Card to a ResolverTerminal block P1 contains

Pagina 16

Resolver Feedback Option Card for PowerFlex® 700S Drives 9 Connection ExamplesResolver Interface - Clockwise Rotation = Count UpResolver Interface -

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 20D-RES-A0 PowerFlex 700S Resolver Feedback Option Manual de usuario

Busca en linea o descarga Manual de usuario para Equipo Rockwell-automation 20D-RES-A0 PowerFlex 700S Resolver Feedback Option. Rockwell Automation 20D-RES-A0 PowerFlex 700S Resolver Feedback Option User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 20D-RES-A0 PowerFlex 700S Resolver Feedback Option