Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui Manual de usuario Pagina 23
- Pagina / 112
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installing, Powering, and Adjusting the OIM
3-3
Step 4. Deburr the drilled holes and cutout.
Step 5. Remove the backing from the gasket. Place the gasket around the cutout on
the inside of the enclosure door.
Step 6. Place the OIM on the gasket and align the mounting holes.
Step 7. Place the bezel around the cutout on the outside of the enclosure hole and
align the mounting holes.
Step 8. Secure the bezel and the OIM to the enclosure door using the hardware
included in the kit.
Step 9. Attach the serial cable to the OIM. Provide appropriate strain relief support
for the cable.
Step 10. Connect the OIM ground wire to an appropriate enclosure ground.
Figure 3.1 – Enclosure Cutout Dimensions
!
ATTENTION:The user must install an appropriate hardwired equipment
ground between the OIM, the drive, and the drive enclosure. This
prevents electrostatic discharge within the equipment. Failure to
observe this precaution could result in damage to or destruction of the
equipment.
- User Guide 1
- Version 2.0 1
- Contents 3
- List of Figures 5
- List of Tables 7
- 1.2 Related Publications 10
- Introduction to the OIM 11
- Display, and Indicators 13
- 2.2 The Display 17
- 2.2.2 Key Indicators 18
- Installing, Powering 21
- 3.2 Powering Up the OIM 24
- Using the OIM 31
- Figure 4.1 – Main Menu Screen 32
- Using Quick Start to 41
- Program the Drive 41
- Regulation 44
- REGULATION TYPE (P.048) 48
- ENCODER PPR (U.001) 49
- MOTOR POLES (U.002) 49
- MOTOR NAMEPL RPM (U.005) 50
- MOTOR NAMEPL HP (U.022) 50
- ACCEL TIME (P.001) 51
- DECEL TIME (P.002) 52
- MINIMUM SPEED (P.003) 52
- MAXIMUM SPEED (P.004) 53
- CURRENT LIMIT (P.005) 53
- MAGNET CURRENT PRCNT (U.006) 54
- Using the OIM to Monitor and 55
- Control the Drive 55
- 6.3.1 Starting the Drive 59
- 6.3.2 Stopping the Drive 59
- Troubleshooting the Drive 60
- 7.2.1 Reviewing the Fault Log 62
- Figure 7.6 – Alarm Menu 64
- Figure 7.8 – Diagnostics Menu 65
- 7.6 OIM Failures 67
- Panel Keypad/Display Codes 68
- Software I/M Parameters and 70
- Parameter Numbers 70
- Input r.010 Option Port 76
- Input r.015 Option Port 78
- GV3000/SE OIM Menu and 88
- Parameter Organization 88
- Installed) 93
- • RMI Inputs 93
- • RMI Outputs 93
- B.1.10 Memory Functions 94
- B.1.11 Additional Parameters 94
- B.2.10 Memory Functions 100
- B.2.11 Additional Parameters 100
Relacionado con productos y manuales para Equipo Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui
Equipo Rockwell-automation FlexPak/WebPak 3000 DC Drive AutoMax Network Commu Manual de usuario
(108 paginas)
(108 paginas)
Equipo Rockwell-automation 20D PowerFlex 700S/700H Frames 10...14 IP00, NEMA/ Manual de usuario
(64 paginas)
(64 paginas)
Equipo Rockwell-automation Sipha 6 Coded Magnetic Interlock Sensor Actuator Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1769-L30ER_L30ERM_L30ER-NSE_L33ERM_L33ER_L36ERM Co Manual de usuario
(88 paginas)
(88 paginas)
Equipo Rockwell-automation T8449 Trusted TMR 24Vdc Valve Monitor Module Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation FactoryTalk AssetCentre Machine Edition Installati Manual de usuario
(44 paginas)
(44 paginas)
BlackWing Projectors user manuals
The list of BlackWing Projectors products contains 1 user manuals for 1 models. All pdf user’s guides are available for download or viewing online.
Comentarios a estos manuales