Rockwell-automation 1734-AENT POINT I/O EtherNet/IP Adapter Module Manual de usuario descargar pdf (Pagina 56)

Publication 1734-UM011D-EN-P - May 2011

40 Configure the Adapter for Direct Connection in RSLogix 5000 Software

1. From the main menu, choose Communications>Who-Active.

The Who Active dialog opens.

2. Navigate to select the slot where the controller is located in the chassis.

3. Choose Set Project Path.

4. Choose Download.

The Download dialog opens with a reminder of the following.

• The controller is in Remote Run mode.

• The mode changes to Remote Program prior to download.

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 157 158

Catalog Number 1734-AENT 1
User Manual 1
Important User Information 2
ATTENTION 3
How to Use This Manual 4
System Components 5
Where to Find More 6
Information 6
Terminology 7
Preface ix 9
Table of Contents 11
xiii 13
Summary of Changes 15
About the Adapter 17
Adapter Replacement 18
About the Adapter 3 19
Adapter Features 20
Hardware/Software 21
Compatibility 21
What the Adapter Does 21
Use of the Common 21
Industrial Protocol (CIP) 21
Understand the 22
Producer/Consumer Model 22
Specify the Requested 22
Packet Interval (RPI) 22
Support of Rack-optimized 23
Before You Begin 24
Install the Adapter 25
Mount the Adapter on a DIN 26
Rail Before Installing 26
Mount or Replace 27
Existing System 27
Wire Your Adapter 28
Mounting Dimensions 29
14 Install the Adapter 30
What This Chapter Contains 31
Configuration 32
Requirements 32
IP Address 33
Gateway Address 33
Subnet Mask 34
Set the Network Address 35
Use the Rockwell 36
BootP/DHCP Utility 36
Save the Relation List 38
Use DHCP Software to 39
Configure Your Adapter 39
Set Up the Hardware 41
Create the Example 42
Application 42
Configure the I/O 43
Name Local_ENB 46
IP Address 10.88.70.4 46
Revision 3.1 46
Add the Relay Output Module 49
The New Module dialog opens 50
Name POINT_Relay_Output 51
Add the Digital Output Module 52
Name POINT_Digital_Output 53
Edit the Controller Tags 54
Create the Ladder Program 55
Download the Program to 55
Verify the Module Chassis 57
8. Click OK to continue 58
Configure the Adapter with 59
Fixed IP Address 59
Recover From an 60
Overloaded Adapter 60
Software 61
Configure the I/O Modules 64
Revision 1.1 66
Connection 69
5. Choose Connection 70
Verify the Module 75
Chassis Size 75
3. Select Properties 76
4. Click the Connection tab 76
→ Save to save the project 77
Access Module Data 78
LED Status Indicators 79
Adapter Web Pages 83
Work with the Diagnostics 85
70 Adapter Web Pages 86
Use the Network Settings Page 87
72 Adapter Web Pages 88
Adapter Web Pages 73 89
Use the I/O Connections Page 90
Adapter Web Pages 75 91
Work with the 92
Configuration Pages 92
Use the Identity Page 93
78 Adapter Web Pages 94
Adapter Web Pages 79 95
Work with the Browse 96
Chassis Page 96
•Module Revision 99
• Serial Number 99
• Status 99
84 Adapter Web Pages 100
Communication Driver 101
Configure the AB_ETH/IP 102
Controller Tag Reference 105
Valid Number Ranges for 106
RSLogix 5000 Data Types 106
Digital 2 POINT Input 107
Digital 4 POINT Input 108
Digital 2 POINT Output – 109
Without Diagnostic Status 109
With Over Load and Open 110
Load Diagnostic Status 110
With Over Load Diagnostic 111
Digital 4 POINT Output – 112
Analog 2 Channel Input 114
INT 0 0…7,000 (0.00…70.00) 121
Analog 2 Channel Output 123
Specialty I/O 127
Stored Data 131
Program Fault 131
Decimal Position 134
Gate Interval 134
Program Fault Note 136
SSI Word Delay Time 138
Sensor Resolution 138
Sensor Cycle 138
Compare 0,1 Value 138
Present / Latched Data 139
Quick Start 145
Configure the Adapter 146
Enter Adapter Properties 147
134 Quick Start 148
Configure 1734 POINT I/O 149
Modules 149
136 Quick Start 150
IMPORTANT 151
Configure an Ethernet 152
Driver in RSLinx Software 152
Quick Start 139 153
140 Quick Start 154
142 Index 156
Rockwell Automation Support 158
Documentation Feedback 158

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 1734-AENT POINT I/O EtherNet/IP Adapter Module Manual de usuario Pagina 56

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 1734-AENT POINT I/O EtherNet/IP Adapter Module