Rockwell-automation 1747-DTAM-E,D17476.1 Data Table Access Module (DTA Manual de usuario Pagina 88
- Pagina / 116
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9-8 Troubleshooting
Publication 1747-6.1
Troubleshooting MSG
Instruction Error
Codes
When an error condition occurs with a Message Instruction (MSG),
the error code and its description are indicated in the Data Monitor
display.
INSTRUCTION ERRORS
Error
Code
Fault Description
02H
Target node is busy. The MSG instruction will automatically reload. If other
messages are waiting, the message is placed at the bottom of the stack.
03H Target node cannot respond because message is too large.
04H
Target node cannot respond because it does not understand the command
parameters OR the control block may have been inadvertently modified.
05H Local processor is offline (possible duplicate node situation).
06H Target node cannot respond because requested function is not available.
07H Target node does not respond.
08H Target node cannot respond.
09H Local modem connection has been lost.
10H
Target node cannot respond because of incorrect command parameters or
unsupported command.
11H Local file has constant file protection.
12H Local channel configuration protocol error exists.
13H Local MSG configuration error in the Remote MSG parameters.
14H Local communication driver is incompatible with the MSG instruction.
15H Local channel configuration parameter error exists.
16H Target or Local Bridge address is higher than the maximum node address.
17H Local service is not supported.
18H Broadcast (Node Address 155) is not supported.
19H
Improperly formatted Logical ASCII Address string. String not properly
terminated with a NULL character or the string length does not match the
value in the length parameter.
20H PCCC Description: Host has a problem and will not communicate.
30H
PCCC Description: Remote station host is not there, disconnected, or shut
down.
37H Message timed out in local processor.
38H Message disabled pending link response.
40H PCCC Description: Host could not complete function due to hardware fault.
50H Target node is out of memory.
60H Target node cannot respond because file is protected.
70H PCCC Description: Processor is in Program mode.
80H
PCCC Description: Compatibility mode file missing or communication zone
problem.
90H PCCC Description: Remote station cannot buffer command.
B0H PCCC Description: Remote station problem due to download.
C0H PCCC Description: Cannot execute command due to active IPBs.
D0H
No IP address configured for the network, -or-
Bad command – unsolicited message error, -or-
Bad address – unsolicited message error, -or-
No privilege – unsolicited message error.
- Data Table 1
- Access Module 1
- Allen-Bradley 1
- Important User Information 2
- Summary of Changes 3
- S-2 Summary of Changes 4
- Table of Contents 5
- Table of Contents v 7
- Who Should Use this 9
- Purpose of this Manual 9
- Contents of this Manual 10
- Related Documentation 11
- Common Techniques 11
- Used in this Manual 11
- Allen-Bradley Support 12
- Local Product Support 12
- Technical Product Assistance 12
- Data Table Access Module 13
- Overview 13
- Installation and Power Up 15
- 2-2 Installation and Power Up 16
- Installation and Power Up 2-3 17
- Connecting Your 18
- Equipment 18
- Installation and Power Up 2-5 19
- Module Configuration 20
- Installation and Power Up 2-7 21
- Access Port View 21
- Power-Up Sequence 22
- Module Setup Procedure 23
- Factory Default 24
- Settings 24
- Entering the Setup 25
- Selecting the 26
- Language 26
- Selecting the Node 26
- Setting the Baud Rate 27
- Setting the Auto 27
- Attach Function 27
- Backlighting the LCD 28
- Setting the Monitor 28
- Override Function 28
- Accepting Module 29
- Setup Parameters 29
- Using the Module 29
- 3-8 Module Setup Procedure 30
- AttachingtoaProcessor 31
- Auto Attach Procedure 32
- Attaching to a Processor 4-3 33
- Attachingtoa 34
- Password Protected 34
- Processor 34
- Monitoring and Modifying Data 35
- Logical Data File 37
- Addressing 37
- Backspace Function 38
- During Data File 38
- Address Entry 38
- Quick Access 39
- .1 40
- Entering Data File 41
- Addresses 41
- Entering Bit Addresses 41
- Entering Integer Addresses 42
- How to Change 43
- Displayed Data File 43
- Elements 44
- How to Change Data 46
- File Values 46
- How to Change Word Values 46
- 0000000000101000 49
- Quick Recall Functions 51
- Using Quick Recall 52
- Functions 52
- Clearing Quick Recall 53
- 6-4 Quick Recall Functions 54
- Processor Control Functions 55
- Changing the 56
- Processor to Program 56
- Viewing Processor 56
- Clearing Processor 57
- Transferring Memory 58
- Message Capability 61
- Programming the MSG 62
- Instruction 62
- 5/02 Control Block 62
- Configuration 62
- Message Capability 8-3 63
- 5/03 Control Block 64
- Message Capability 8-5 65
- 8-Word Message 66
- 16-Word Message 67
- 12-Word Message 68
- 13-Word Message 69
- 18-Word Message 70
- 1-Word Message 71
- Application Example 1 72
- Message Capability 8-13 73
- B3:1.0/1 74
- B3:1.0/3 75
- ENTER LOW RANGE 76
- ENTER HIGH RANGE 76
- NO VALUE ENTERED 77
- Application Example 2 78
- Message Capability 8-19 79
- ENTER NEW VALUE? 80
- Troubleshooting 81
- 9-2 Troubleshooting 82
- Module Problems 83
- Using the LCD 83
- Communication 84
- Problems Using the 84
- Troubleshooting 9-5 85
- 9-6 Troubleshooting 86
- Function Problems 87
- Troubleshooting MSG 88
- Instruction Error 88
- Troubleshooting 9-9 89
- 9-10 Troubleshooting 90
- Processor Faults 91
- 9-12 Troubleshooting 92
- Troubleshooting 9-13 93
- 9-14 Troubleshooting 94
- Specifications 95
- Characteristics 96
- Not accessible from the DTAM 97
- Address Structure 98
- Data File 3 - Bit 101
- Data File 4 - Timers 102
- Data File 5 - Counters 103
- Data File 6 - Control 104
- Data File 7- Integer 105
- Publication 1747-6.1 106
- Module Display Character Set 107
- Mounting Template 109
- D-2 Mounting Template 110
- 111
- I-2 Index 112
- I-4 Index 114
Relacionado con productos y manuales para Equipo Rockwell-automation 1747-DTAM-E,D17476.1 Data Table Access Module (DTA
Equipo Rockwell-automation 1792D-4BV4D ArmorBlock MaXum 4 Input/4 Output Modu Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1763 MicroLogix 1100 Programmable Controllers User Manual de usuario
(256 paginas)
(256 paginas)
Equipo Rockwell-automation 1763-L16xxx MicroLogix 1100 Programmable Controlle Manual de usuario
(36 paginas)
(36 paginas)
Equipo Rockwell-automation 1785-TR10B2 Coax Transceiver for 10BASE2 Installat Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1771-DBMEM1,1771-DBMEM2 INSTL.INST EEPROM MEMORY M Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1788-EN2DNR EtherNet/IP to DeviceNet Linking Devic Manual de usuario
(52 paginas)
(52 paginas)
Equipo Rockwell-automation 1788-FFCT NI-FBUS Configurator User Manual Manual de usuario
(86 paginas)
(86 paginas)
Equipo Rockwell-automation 1764-RPL-TRM1 MicroLogix 1500 Electrostatic Discha Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1747-Mxx Memory Module Adaptor Installation Instru Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1772-AF3,D17726.5.2 User Manual AUX FUNCT PROM Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation Logix5000 Controllers Structured Text Programming Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 1771-A2BSS_A3B1SS Install Instruc Universal I/O Ch Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 1746-NR4 SLC 500 RTD/Resistance Input Module/ Inst Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1734-XXXX POINT I/O and ArmorPOINT I/O DeviceLogix Manual de usuario
(112 paginas)
(112 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.133 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales