Rockwell-automation 1771-IR , D17716.5.76 RTD INPUT MODULE Manual de usuario Pagina 36
- Pagina / 68
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Module Calibration
Chapter 7
73
Table 7.A
Write
Block T
ransfer W
ord 15
W
ord Bit
17 16 15 14 13 12 11 10 07 06 05 04 03 02 01 00
Inhibit Calibration on Channel
Requested Auto-Calibration
W
ord 15
Set
these
bits to 0
6 5 4 3 2 1
Set these bits to 0
Requested
Save
Values
Requested
Gain Cal.
Requested
Of
fset Cal.
NOTE: Normally, all channels are calibrated simultaneously (bits 10–15 of
word 15 are octal 0). To disable calibration on any channel, set (1) the
corresponding bit 10 through 15 of word 15.
4. Queue block transfer reads (BTRs) to monitor for offset calibration
complete and any channels which may have not calibrated successfully.
Refer to Table 7.B.
Table 7.B
Read
Block T
ransfer Word 9
Word
Bit
17 16 15 14 13 12 11 10 07 06 05 04 03 02 01 00
Uncalibrated Channels
Auto-Calibration Status
W
ord 9
Not
used
6 5 4 3 2 1
Cal.
Fault
EEPROM
Fault
Not used
Save to
EEPROM
Complete
Gain Cal.
Complete
Of
fset Cal.
Complete
5. Proceed to gain calibration below.
Gain Calibration
Calibrating gain requires that you apply 402.00 ohms across each input channel.
Normally all inputs are calibrated together. To calibrate the gain of an input,
proceed as follows:
1. Connect 402.00 ohm resistors across each input channel as shown in
Figure 7.2.
- RTD Input Module 1
- Cat. No. 1771-IR Series B 1
- Important User Information 2
- Table of Contents 3
- Table of Contentsii 4
- Table of Contents iii 5
- Using This Manual 6
- Chapter 1 8
- Related Publications 8
- Module Description 9
- Features of the Input Module 9
- Chapter 2 10
- How Analog Modules 10
- Communicate with 10
- Programmable Controllers 10
- Series B Cat. No. 1771-WF 11
- 1771-6.5.76 11
- Chapter Objectives 12
- Before You Install Your Input 12
- Electrostatic Damage 12
- Chapter 12
- Chapter 3 14
- Connecting Wiring 14
- Grounding the Input Module 16
- Installing the Input Module 16
- Interpreting the Indicator 17
- Chapter Summary 17
- Module Programming 18
- Chapter 4 19
- PLC-2 Program Example 19
- Module Scan Time 24
- Module Configuration 25
- Units of Measure 26
- Configuring 28
- Block for a 28
- Chapter 5 29
- Bit/Word Descriptions 29
- Default Configuration for the 30
- Module Status and Input Data 31
- Chapter 6 32
- Module Calibration 34
- Performing Auto-calibration 35
- Complete 36
- Chapter 7 37
- Save Calibration Values 38
- Performing Manual Calibration 38
- Offset Calibration 39
- Gain Calibration 40
- Troubleshooting 42
- Chapter 8 43
- Status Reported in Word 9 44
- Specifications 45
- Appendix A 46
- Programming Examples 47
- Appendix B 48
- PLC-3 Family Processors 49
- PLC-5 Family Processors 50
- Data Table Formats 52
- Data Formats 53
- Appendix C 53
- Signed-magnitude Binary 53
- Two's Complement Binary 54
- Processors) 55
- PLC-2/20 Processors) 56
- Appendix D 56
- 2 and 4-Wire RTD Sensors 60
- 2 and 4-Wire Sensors 61
- Appendix E 61
- Connecting 4-Wire Sensors 61
- RTD Input Modules 63
- Differences between Series A 64
- Appendix F 64
- Printed in USA 68
Relacionado con productos y manuales para Equipo Rockwell-automation 1771-IR , D17716.5.76 RTD INPUT MODULE
Equipo Rockwell-automation 1756-RIO ControlLogix Remote I/O Communication Int Manual de usuario
(176 paginas)
(176 paginas)
Equipo Rockwell-automation 1738-IA2M12AC4 ArmorPoint AC Input Modules, Series Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 1756-xxxx ControlLogix Chassis and Power Supplies Manual de usuario
(60 paginas)
(60 paginas)
Equipo Rockwell-automation 1753-OW8 GuardPLC 8-Relay Output Module Installati Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1783-BMxxx Stratix 5700 Ethernet Managed Switches Manual de usuario
(294 paginas)
(294 paginas)
Equipo Rockwell-automation 1756-CNB ControlLogix ControlNet Bridge Module, Se Manual de usuario
(36 paginas)
(36 paginas)
Equipo Rockwell-automation 1758-RTU202 Datasite Installation Instructions Manual de usuario
(28 paginas)
(28 paginas)
Equipo Rockwell-automation 1755-BAT Replacing the Battery in the GuardPLC 200 Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1794-IM8,1794-OM8 FLEX I/O 220V ac Input and Outpu Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1757-FFLD Linking Device Configuration Manual Manual de usuario
(150 paginas)
(150 paginas)
Equipo Rockwell-automation 1794-ASBLT/A FLEX I/O Remote I/O Adapter Installat Manual de usuario
(6 paginas)
(6 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.189 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales