Rockwell-automation 1771-N SERIES High Resolution Analog Module User M Manual de usuario Pagina 111
- Pagina / 188
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Block Transfer Write and Block Transfer Read Configurations for 2 Output/2 Input 1771-N Series Modules D–7
Publication 1771ĆUM127B-EN-P - December 2002
DefinitionWord
Decimal Bit
(Octal Bit)
Bit 05
High clamp. This bit is set if alarms are enabled and the output
data is higher than the high clamp value
Bit 06
Rate alarm. This bit is set if alarms are enabled and the output
data changed faster than the programmed ramp rate.
Word 4 continued
Bit 07
Bad data. This bit is set if BCD data format was chosen and
output value was not a legal BCD value.
Word 4 continued
Bits 08 (10)
Bad programming. This bit is set if the most recent BTW
contained improper programming data for this channel
Bit 09 (11)
Bad calibration. This bit is set if the channel has not had a valid
calibration.
Bits 10-14
(12-16)
Not used. Always 0.
Bit 15 (17)
I/O select bit.
0 = output,
1 = input.
This bit is set to 0.
Word 5 Bits 00-17 Channel 1 Raw data sent to DAC.
Words 6 and 7 Same as words 4 and 5, but for channel 2
Bit 00
Underrange bit. This bit is set if the input signal is below the
input channels minimum range.
Bit 01
Overrange bit. This bit is set if the input signal is above the
input channels maximum range.
Bits 02-03 Not used. Always 0.
Bit 04
Low alarm. This bit is set if alarms are enabled and the input
signal is lower than the low alarm setpoint.
Bit 05
High alarm. This bit is set if alarms are enabled and the input
signal is higher than the high alarm setpoint.
Word 8
Bit 06
Rate alarm. This bit is set if alarms are enabled and the input
signal changed at a rate faster than the input rate alarm
setpoint.
Bit 07 Not used. Always 0.
Bit 08 (10)
Bad program. This bit is set if any of the channel level
programming data is illegal.
Bit 09 (11)
Bad calibration. This bit is set if the channel has not had a valid
calibration.
Bits 10-14
(12)-16
Not used. Always 0.
Bit 15 (17)
I/O select bit.
0 = output,
1 = input.
This bit is set to 1.
Word 9
Bits 00-15
(00-17)
Channel 3 input data.
- User Manual 1
- Important User Information 2
- ATTENTION 3
- Using this Manual 5
- Related Products 6
- Product Compatibility 6
- Related Publications 7
- Using this ManualP–4 8
- Table of Contents 9
- Chapter 4 10
- Configuring the Module 10
- Table of Contents toc-iii 11
- Table of Contentstoc-iv 12
- Table of Contents toc-v 13
- Table of Contentstoc-vi 14
- Overview of the High 15
- Resolution Isolated 15
- Analog Modules 15
- Features of the High 16
- Analog Series Modules 16
- Refer to 17
- Appendix 17
- Installing the Module 19
- Determine Module 20
- Location in the I/O Chassis 20
- Install the Analog Module 20
- Install the Module in the 21
- Chassis and Connect the 21
- Connecting Wiring 23
- • R = return 26
- • I = input 26
- • O = output 26
- • S = shield 26
- Connecting 4ĆWire 27
- Sourcing Input Analog 28
- Making Your Own Cables 29
- Grounding the Field 30
- Interpreting the 31
- Indicator Lights 31
- Chapter Summary 31
- 2–14 Installing the Module 32
- Communicating With Your 33
- Analog Module 33
- PLCĆ2 Programming 34
- PLCĆ3 Program Example 34
- PLCĆ5 and PLCĆ5/250 35
- Program Example 35
- Module Scan Time 36
- Programming Samples 36
- Setting Up the Data 39
- Table File 39
- Default Configurations 42
- Module Level 43
- Programming Features 43
- Real Time Sampling 45
- Output Channel 46
- Clamping 49
- Alarm Enable 50
- Reset State 50
- Input Channel 51
- Alarm Deadband 52
- Thermocouple Type 54
- Configuration Block for a 55
- Block Transfer Write 55
- Module Status and Input Data 61
- Block Transfer Read 62
- Data Format 62
- Data Header 63
- Input Status Data 64
- Output Status Data 66
- Module Calibration 69
- Calibrating Your Module 70
- Manual Calibration 71
- Figure 6.1 73
- Termination Panel 73
- Output Channel Calibration 75
- Troubleshooting 77
- Troubleshooting with 78
- Status Reported by 78
- Specifications 81
- Grounding Guidelines." 82
- Temperature Specifications 83
- SpecificationsA–6 86
- Important: If you require 60 87
- SpecificationsA–8 88
- Word/Dec. Bit 101
- Word/Octal Bit 101
- Transfer Read Configurations 105
- Series Modules 105
- CSA Hazardous Location 183
- Rockwell Automation Support 188
- Documentation Feedback 188
Relacionado con productos y manuales para Equipo Rockwell-automation 1771-N SERIES High Resolution Analog Module User M
Equipo Rockwell-automation 1792D-8BIO8E ArmorBlock MaXum 8 Input/8 Output Mod Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1792D-16BT0LP INSTL INSTR ARMORBLOCK LP2 16 Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation Logix5000 Controllers Major, Minor, and I/O Faults Manual de usuario
(53 paginas)
(53 paginas)
Equipo Rockwell-automation 1756-HIST2G FactoryTalk Historian ME 2.2 Installat Manual de usuario
(28 paginas)
(28 paginas)
Equipo Rockwell-automation 1769-IQ6XOW4 Compact Combination 24V dc Sink/Sourc Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1746-NO8V SLC 500 8-Point Analog Output Module/ Us Manual de usuario
(74 paginas)
(74 paginas)
Equipo Rockwell-automation 1771-OD16 AC (120V) ISO Output Installation Instru Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 1792D-OB4D ArmorBlock MaXum 4 Output Module Series Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1747-DPS1, 1747-DPS2 Port Splitter Installation In Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1753-IB20XOB8 GuardPLC Digital Input/Output Module Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1793-IE4S INSTL INSTR FLEX INTEGRA 4 INPUT ANALOG Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.174 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales