Rockwell-automation 20-750-ENETR PowerFlexDual-Port EtherNet/IP Option Manual de usuario Pagina 16
- Pagina / 200
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
16 Rockwell Automation Publication 750COM-UM008A-EN-P - July 2012
Chapter 1 Getting Started
Tap Mode of Operation (only with PowerFlex 755 drives)
Step Action See
1 Review the safety precautions for the option module. Throughout this manual
2 Verify that the PowerFlex drive is properly installed. PowerFlex 750-Series AC Drive
Installation Instructions,
publication 750-IN001
3 Set the option module IP address.
a. When using the option module node address switches, set the IP
address now and proceed with step 4. When using a DHCP server,
BOOTP server, or option module parameters to set the IP address,
first perform step 3b and all of step 4. Then proceed with step 5.
b. Verify that the PowerFlex drive is not powered.
Chapter 2,
Installing the Option Module
4 Install the option module.
a. Insert the option module in only PowerFlex 755 drive Port 4 or 5.
Use the captive crews to secure and ground the option module to
the drive.
b. Connect the option module to the network by using an Ethernet
cable.
Network Communication Option
Card Installation Instructions,
publication 750COM-IN002
and
Chapter 2,
Installing the Option Module
5 Apply power to the option module.
a. The option module receives power from the drive. Verify that the
option module is installed correctly and then apply power to the
drive. The status indicators should be green. If they flash red, there
is a problem. See Chapter 7
, Troubleshooting.
b. Configure and verify key drive parameters.
Chapter 2
,
Installing the Option Module
6 Configure the option module for your application.
Set option module parameters for the following functions as required by
your application:
• IP address, subnet mask, and gateway address (only when not using
option module node address switches)
• Data rate
• Web enable and features
Chapter 3
,
Configuring the Option Module
7 Set (or verify) the IP address for the embedded EtherNet/IP adapter in
the PowerFlex 755 drive.
PowerFlex 755 Drive Embedded
EtherNet/IP Adapter User Manual,
publication 750COM-UM001
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Conventions Used in This 7
- Rockwell Automation 7
- Additional Resources 8
- Getting Started 9
- Features 10
- Option Module Operating 11
- Understanding Parameter 12
- Compatible Products 13
- Required Equipment 13
- Safety Precautions 14
- Quick Start 15
- Installing the Option Module 17
- Setting the Operating Mode 19
- Setting the Node Address 20
- Connecting the Option 22
- Module to the Drive 22
- Module to the Network 23
- ENET2 network ports are used 24
- Start-Up Status Indications 26
- and page 115 27
- or page 116 28
- Commissioning the Option 30
- Configuring the Option Module 31
- Using the PowerFlex 20-HIM 32
- A6 or 20-HIM-C6S HIM to 32
- Access Parameters 32
- Setting the Option Module 32
- Node Address 32
- 1<<3 33
- Setting the IP Address 36
- Setting the Subnet Mask 37
- Setting the Gateway Address 37
- Setting the Data Rate 38
- Autodetect 0 38
- 0<<4 38
- Selecting Master-Slave or 39
- Peer-to-Peer Hierarchy 39
- (Adapter mode only) 39
- Simple Peer I/O Configuration 41
- 0<<2 42
- 10.00 Secs 44
- Changing the Fault Action 46
- Disabled 0 48
- Resetting the Option Module 49
- Host Drive 50
- 240V 4.2A 50
- Rev 3.002 Ser. A 50
- Viewing the Option Module 51
- Status Using Parameters 51
- Updating the Option Module 52
- Firmware 52
- Configuring the I/O 53
- Uploading the Electronic 54
- Data Sheet (EDS) File 54
- Example (Adapter mode 54
- Chapter 4 Configuring the I/O 56
- Box Setting 56
- Configuring the I/O Chapter 4 61
- ADC and Logix Memory 74
- Monitoring ADC Progress 79
- Chapter 5 87
- About I/O Messaging 87
- Understanding the I/O Image 88
- Using Logic Command/Status 89
- Using Reference/Feedback 89
- Using Datalinks 90
- Example Ladder Logic 91
- Program Information 91
- Versions 94
- Program 95
- Program Tags 96
- Example Datalink Data 97
- Generic Profile 98
- Chapter 6 99
- About Explicit Messaging 99
- ControlLogix Controller 101
- Examples 101
- Single Parameter 103
- Multiple Parameters 105
- Request (Source Data) array 112
- Troubleshooting 113
- Indications for Adapter Mode 114
- Operation 114
- Indications for Tap Mode 116
- Viewing Option Module 118
- Diagnostic Items 118
- Viewing and Clearing Events 122
- Chapter 8 125
- Enabling the Option Module 125
- Web Pages 125
- Viewing Web Pages in 125
- Adapter Mode 125
- Adapter Mode Process 128
- Display Pop-up Dialog Box 128
- Adapter Mode TCP/IP 129
- Configuration Web Page 129
- Adapter Mode Configure E 130
- Adapter Mode Device 133
- Information Pages 133
- Viewing Web Pages in Tap 136
- Specifications 137
- Electrical 138
- Mechanical 138
- Environmental 138
- Regulatory Compliance 138
- Option Module Parameters 139
- About Parameter Numbers 140
- How Parameters Are 140
- Organized 140
- Parameters for Adapter 140
- Mode Operation 140
- Host Parameters—Adapter Mode 146
- Parameters for Tap Mode 150
- Host Parameters—Tap Mode 152
- Appendix C 153
- Supported Data Types 153
- Identity Object 154
- Assembly Object 155
- Register Object 156
- PCCC Object 157
- N-Files 159
- DPI Device Object 160
- Class Attributes 161
- Instance Attributes 162
- DPI Parameter Object 163
- Formula number 165
- Extended DPI descriptor 165
- Descriptor Attributes 166
- Formulas for Converting 168
- Common Services 168
- Object Specific Services 168
- DPI Fault Object 169
- DPI Alarm Object 171
- DPI Diagnostic Object 173
- DPI Time Object 175
- Host DPI Parameter Object 177
- TCP/IP Interface Object 183
- Ethernet Link Object 185
- 750-Series Drives 187
- Logic Status Word 188
- Glossary 189
- Rockwell Automation Support 200
- Documentation Feedback 200
Relacionado con productos y manuales para Equipo Rockwell-automation 20-750-ENETR PowerFlexDual-Port EtherNet/IP Option
Equipo Rockwell-automation 500LG Lighting Contactor Instruction Manual Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 194L Control and Load Switches 12 A / 16 A for 45 Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 281G ArmorStart Distributed Motor Controller - Get Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 140U J-Frame CB Thermal Magnetic Breakers and Moto Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 294E ArmorStart LT EtherNet/IP Version - User Manu Manual de usuario
(252 paginas)
(252 paginas)
Equipo Rockwell-automation 193-EE Bul 193 E1 PLUS Overload Relay Application Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 440P Bulletin 440P 2 N.C. Small Metal Safety Posit Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 150-SM6 SMC-50 Soft Starter Parameter Configuratio Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 440R MSR178DP Minotaur Installation Instructions Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales