Rockwell-automation FlexPak 3000 Power Module Version 4.2 Manual de usuario Pagina 202
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
APPENDIX G
FlexPak 3000 49’1340 e
G-2
Table G.1 - User Quick Reference Table for Input Parameters (continued)
Par.
Parameter Parameter Selection / Pg Initial Factory User Data
No.
Adjustment Range B- Setting Date Setting
105 ANLG MAN REF ZERO ADJ -200 - +200 4 0
106 MANUAL REF SELECT
• ANALOG
• MOP
25 ANALOG
107 TRIM REF REGISTER + 100.0% 51 0%
108 TRIM REFERENCE SELECT
• ANALOG MANUAL
• ANALOG IN 1
• NETW IN REG 1
• NETW IN REG 2
• NETW IN REG 3
• ANALOG IN 2
• REGISTER
51 REGISTER
109 TRIM RANGE 0 - +100.0% 51 0.0%
110 TRIM MODE SELECT
• NO TRIM
• INCREMENTAL
• PROPORTIONAL (DRAW)
51 NO TRIM
111 AUTO MODE MIN BYPASS
• OFF
• ON
8OFF
112 AUTO MODE RAMP BYPASS
• OFF
• ON
8OFF
113 STOP SPEED THRESHOLD 0 - MAXIMUM SPEED (P.004)
in *RPM
49 0 (*RPM)
114
(3)
STOP MODE SELECT
• RAMP
• COAST/DB
• CURRENT LIMIT
49 RAMP
115 MOP ACCEL TIME ACCELERATION TIME (P.001) -
300.0 seconds
29 5.0 seconds
116 MOP RESET ENABLE
• OFF
• ON
30 OFF
117 PRESET SPEED 1 MINIMUM SPEED- MAX SPEED 43 250 *RPM
118 PRESET SPEED 2 MINIMUM SPEED- MAX SPEED 43 250 *RPM
119 PRESET SPEED 3 MINIMUM SPEED- MAX SPEED 43 250 *RPM
120 MOP DECEL TIME DECEL.. TIME (P.002)- 300 sec 30 5.0 seconds
121 JOG OFF DELAY TIME 0.0 to 10.0 seconds 23 1.0 seconds
122 STOP DECEL SELECT
• 1 = DECELERATION TIME
• 2 = RAMP STOP DECEL TIME
48 1
Feedback Selection
200 FEEDBACK SELECT
• ARMATURE VOLT
• DC TACH
• PULSE TACH
• AC TACH
14 ARM VOLT for
S-6
DC TACH for
S-6R
201 ANALOG TACH GAIN ADJ 0.750 - 1.250 1 1.000
202 ANALOG TACH ZERO ADJ -200 - +200 2 0
203 ANLG TACH VOLTS/1000 18.0 - 200.0 V/1000 RPM 6
60V/1000 RPM
204 ARM VOLTAGE GAIN ADJ 0.750 - 1.250 7 1.000
205 ARM VOLTAGE ZERO ADJ -200 - +200 V 8 0 V
206 IR COMPENSATION 0 - 50 %FLA 22 0% FLA
(*) Or user defined unit.
(3) If drive is configured as a current regulator,
only COAST/DB can be selected.
- FlexPak 3000 Power Module 1
- SW-Version 4.2 1
- Instruction Manual 1
- Table of Contents 3
- 6.0 Quick Start 4
- Appendices 5
- List of Figures 6
- List of Tables 6
- 1.1 Safety Instructions 7
- 1.2 General Notes 8
- 1.3 Manual Scope 8
- 1.4 Related User Manuals 8
- 2.0 Introduction to the Drive 9
- 2.1 Drive Identification 9
- 2.2 Drive Specifications 10
- 2.2.6 DC Voltage Ratings: 11
- (-73/43) 12
- 2.3.1 Logic Inputs: 13
- 2.3.2 Logic Outputs: 13
- 2.3.3 Analog Inputs: 13
- 2.3.4 Analog Outputs: 14
- 2.4 Drive Description 15
- (M/N 317C160D) 16
- (M/N 905FK0101) 16
- 2.5 Controls/Indicators 17
- 2.5.2 Controls 18
- PROGRAM KEYPAD MANUAL FORWARD 19
- MONITOR KEYPAD MANUAL FORWARD 19
- FAULT KEYPAD MANUAL FORWARD 20
- ALARM KEYPAD MANUAL FORWARD 20
- DIAGS KEYPAD MANUAL FORWARD 20
- 3.1 General 25
- 3.3 Install the Drive 25
- 1U 1C 1V 1D 1W 27
- 1C 1U 1V 1W 1D 27
- 25 Ø 1) 29
- 1) Holes for lifting hooks 30
- 3.6 Install the Motor 33
- 3.7 General Wiring Practices 33
- 3.8 Wire the Drive 34
- 3.8.5 Emergency Stop-Function 35
- 3.8.6 Stopping the Drive 35
- INSTALLATION AND WIRING 36
- 49’1340 e FlexPak 3000 3-15 39
- 49’1340 e FlexPak 3000 3-17 41
- 1LG 1 2 03 42
- 4.1 Introduction 43
- 4.2 Test Equipment Needed 43
- 4.3 Power Off Inspection 43
- 4.4 Motor Ground Check 43
- 4.5 Jumper Settings 44
- 4.5.11 Check the 48
- – J30 Jumper 48
- 4.6 Powering Up the Drive 49
- 4.8 Accessing the Main Menu 50
- Adjustments 52
- 4.13 Language Selection 53
- 4.14 Programming Features 54
- 4.14.3 Memory Operations 55
- 4.14.4 Reset Clock 56
- 4.14.5 Define User Units 56
- 4.14.5.2 58
- Load Units 58
- 5.1 Introduction 59
- 6.1 Introduction 63
- N/A = Not Applicable 69
- 6.4.1 Self Tune Setup 70
- 6.4.2 Execute Self-tuning 71
- 6.5 Final Adjustments 72
- 7.1 General 73
- 7.2 Wiring Errors 73
- 7.3 AC Line and Power Input 73
- 7.4 DC Motor 73
- 7.5 Remote M Contactor 74
- 7.6 Optional Kits 74
- 7.7.2 About The Alarm Menu 75
- 7.7.3 Diagnostics Menu 77
- 7.7.4 Diagnostics Configure 77
- CPU OK LED OIM COMM OK LED 78
- 8.0 Replacement of components 81
- Replacement of a thyristor 82
- 8.1 Recommended Spare Parts 83
- 8.2 Accessories 86
- Fuse Holder Dimensions 87
- 1U 1V 1W 3V 3W 89
- U1 V1 W1 90
- EMC Filters for FlexPak 3000 91
- HF Filter 91
- FILTER Line rms ad 92
- E L3 L2 L1 93
- E L3 L2 L1 94
- E L1 L2 L3 95
- LOAD 97
- E L3 L2 L1 98
- FlexPak 3000 49’1340 e 102
- Glossary of Terms 103
- Parameter Range: -200 to 200 108
- (A) terminal 39 113
- (A) terminal 40 113
- (COM) terminal 41 113
- Frequency Input 113
- SPEED LOOP 114
- CURRENT LOOP 114
- Installed 116
- Not Installed 116
- FIELD DELTA HI LIM 119
- 2 = FAULT IMMEDIATELY 125
- 3 = DELAY BEFORE FAULT 125
- WLD RST\ RATIO 141
- * DISABLED 142
- TOP SPEED 142
- SPEED RAMP 142
- OUTPUT (RPM) 142
- APPENDIX D 170
- D-II FlexPak 3000 49’1340 e 170
- 49’1340 e FlexPak 3000 D-1 171
- (Fig.D.6) 172
- (Fig.D.9) 172
- (Fig.D.3) 172
- (Fig.D.4) 172
- (Fig.D.11) 172
- 49’1340 e FlexPak 3000 D-3 173
- 49’1340 e FlexPak 3000 D-5 175
- Netw. Drop 2, Reg. 32 176
- Digital Outputs 1 and 2 177
- Analog and Frequency Outputs 177
- Meter Outputs (n = 1, 2) 178
- 49’1340 e FlexPak 3000 D-9 179
- 49’1340 e FlexPak 3000 D-11 181
- Figure D.11 - Field Block 181
- Analog Inputs 183
- CML FEEDBACK 184
- * n=1 SPD LOOP FEEDBACK 184
- SPD RAMP OUTPUT 184
- *n=2 SPD RAMP INPUT TP 184
- SPD SOURCE SEL OUT 184
- TACH LEAD FLT DELAY 188
- (P.228) 188
- is too high 190
- OIM Parameter Menu Tree 193
- ) not available in SW-V4.1 200
- not available in SW-V4.1 200
- not available in SW-V4.1 200
- User Quick Reference Table 201
- APPENDIX G 202
- Feedback Selection 202
- 49’1340 e FlexPak 3000 G-3 203
- Speed Regulator Adjustm 203
- Self Tuning Set-up 203
- 49’1340 e FlexPak 3000 G-5 205
- 2.0 - FREQ OUT FULL SCALE kHz 206
- MOTOR HOT FLD AMPS 206
- MOTOR RATED 206
- ARM VOLTS 206
- 49’1340 e FlexPak 3000 G-7 207
- Level Detectors 207
- Outer Current Loop 207
- Network Communication 208
- EMC Directive 209
- Mounting Instructions 210
- Configuration 211
- Wiring Instruction 212
- Cross Reference List 213
- APPENDIX J 214
Relacionado con productos y manuales para Equipo Rockwell-automation FlexPak 3000 Power Module Version 4.2
Equipo Rockwell-automation 20D PowerFlex 700H/S Frame 12 Replacement Power St Manual de usuario
(28 paginas)
(28 paginas)
Equipo Rockwell-automation Direct Drive Technology Demonstration Machine Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation LiquiFlo 2.0 Frame 4 Board Interface Assembly Repl Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1440-RMA00-04RC XM-440 Master Relay Module Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation T8433 Trusted TMR Isolated 4-20 mA Analogue Input Manual de usuario
(35 paginas)
(35 paginas)
Equipo Rockwell-automation MD65 Communication Module Cover Installation Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation CEP7-EMR_ CEP7 Remote Reset Installation for CEP7 Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 20B Power Components Repl. Instructions - Frame 5 Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation TDO16AIN 16-Channel Digital Output Termination Car Manual de usuario
(11 paginas)
(11 paginas)
Equipo Rockwell-automation Logix5000 Control Systems: Connect Kinetix 5500 Dr Manual de usuario
(48 paginas)
(48 paginas)
Equipo Rockwell-automation 440R MSR312 Configurable Monitoring Safety Relay w Manual de usuario
(56 paginas)
(56 paginas)
Equipo Rockwell-automation RECOMM-ENET EtherNet/IP Communications Module Manual de usuario
(194 paginas)
(194 paginas)
Equipo Rockwell-automation 1769-L16ER-BB1B_L18ER-BB1B_L18ERM-BB1B CompactLogi Manual de usuario
(76 paginas)
(76 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.194 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales