Rockwell Automation 1203-SSS Manual de usuario Pagina 95
- Pagina / 112
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Use with HyperTerminal Software E-5
PowerFlex 1203-USB Converter User Manual
Publication DRIVES-UM001D-EN-P
Preparing for a Firmware
Update
Please take the following precautions to ensure a successful firmware
update:
• Obtain the new firmware version from Rockwell Automation. Save it to
the hard drive of the computer. Do not attempt to perform an update from
a removable storage device or a network.
• Read all instructions supplied with the new firmware file.
• Use a computer running terminal emulation software that supports
Xmodem transfers. For example, in this appendix we show how to use
HyperTerminal software.
• Record parameter values in the device that will be updated. Updates may
cause parameters to revert to their default settings.
• Verify that the host drive (for example, a PowerFlex 70 EC drive) is
stopped.
• Close all programs except the terminal emulation program being used to
update the device.
• Disable the screen saver and anti-virus programs so that they do not start
during the update.
• Depending on the type of drive, verify the applicable converter
parameter setting shown below.
Updating Firmware
HyperTerminal software can be used to perform firmware updates on the
1203-USB converter and products that implement DPI or DSI, such as
PowerFlex 7-Class drives and peripherals, or PowerFlex 4-Class
peripherals—but not PowerFlex 4-Class drives.
Important:PowerFlex 400 drives can only be updated using a
AK-U9-FLSH1 flash kit. PowerFlex 4, 40, and 40P drives
cannot be updated. Only PowerFlex 4M drives can be updated
using the 1203-USB converter.
For information to update firmware, see the respective Release Note for the
firmware revision you are updating to on the Allen-Bradley website at
http://www.ab.com/support/abdrives/webupdate
.
Type of Drive Converter Parameter Required Setting
DPI Drives Parameter 06 - [Interface Mode] ‘0’ (Auto)
DSI Drives Parameter 01 - [Adapter Cfg] ‘0’ (Auto)
SCANport Drives Parameter 06 - [Interface Mode] ‘0’ (Auto)
- PowerFlex 1203-USB Converter 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Chapter 4 Troubleshooting 6
- Appendix A Specifications 6
- Appendix F History of Changes 7
- About This Manual 9
- Additional Resources 10
- Getting Started 11
- Components 12
- Features 12
- Compatible Products 13
- Required Equipment 14
- User-Supplied Equipment 15
- Safety Precautions 16
- Quick Start 16
- Computer 17
- 1-8 Getting Started 18
- Installing the Converter 19
- Installing the USB Drivers 22
- Installing the Converter 2-5 23
- 2-6 Installing the Converter 24
- Installing the Converter 2-7 25
- 2-8 Installing the Converter 26
- Installing the Converter 2-9 27
- 2-10 Installing the Converter 28
- Installing the Converter 2-11 29
- Installing Connected 30
- Components Workbench 30
- Software 30
- Powering Up the Converter 30
- Removing the Converter 31
- 2-14 Installing the Converter 32
- Configuring the Converter 33
- Using Connected 34
- Configuring the Converter 3-3 35
- Configuring the Converter 3-5 37
- 3-6 Configuring the Converter 38
- to open the Linear List 38
- Resetting the Converter 39
- Updating the Firmware 40
- Using RTU Master Mode for 40
- Configuring the Converter 3-9 41
- Establishing Communication 42
- to open the RSWho window 45
- Troubleshooting 49
- Diamond Status Indicator 50
- RX Status Indicator 50
- TX Status Indicator 50
- Converter Diagnostic Items 51
- Viewing Diagnostic Data 52
- Troubleshooting 4-5 53
- Converter Events 54
- Event Codes for DSI Drives 55
- Viewing and Clearing 56
- Viewing and Clearing DF1 57
- Communication Statistics 57
- Troubleshooting Potential 58
- Problems 58
- Specifications 59
- Environmental 60
- Agency Certification 60
- Converter Parameters 61
- Parameters – DSI Drives 62
- Parameters – SCANport 64
- Drives (DriveExplorer or 64
- DriveExecutive software 64
- Appendix C 65
- Preparing for a Firmware 68
- Viewing and Clearing Events 70
- Appendix D 75
- Appendix E 91
- Updating Firmware 95
- History of Changes 99
- F-2 History of Changes 100
- Glossary 101
- D DF1 Protocol 102
- N NVS (Non-Volatile Storage) 103
- S SCANport 104
- U Update 104
- X Xmodem 104
- Z Zero Data 105
- G-6 Glossary 106
- Rockwell Automation Support 112
- Documentation Feedback 112
Relacionado con productos y manuales para Redes Rockwell Automation 1203-SSS
(20 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales