Rockwell-automation 1441-DYN25-Z Dynamix 2500 Data Collector Manual de usuario Pagina 74
- Pagina / 218
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
74 Rockwell Automation Publication 1441-UM001B-EN-P - September 2012
Chapter 3 Setting Up Measurements
Figure 12 - RSS filter
Measurement Units
The Emonitor software and the Dynamix 2500 data collector support many
different measurement units. The measurement units that appear in the data
collector are text that depend on the following definitions:
• Type of measurement definition
• Units for the measurement definition
• Transducer specification used in the collection specification for the
measurement definition
The data collector collects data for english units, metric units, or decibels. It uses
the units that you select in the Emonitor software. You can select units from a
single system, for example, English g’s, in/sec, or you can mix units from different
systems, for example, English g’s, in/sec and Metric m/s
2
, m/sec) in one list.
The Dynamix 2500 data collector loads the exact text string from the Emonitor
software. The signal detection type, for example, peak, rms and true peak is
appended to the units on the data collector.
IMPORTANT
Using the 0.36 Hz (21.6 CPM) low cutoff filter for integrated
measurements or the 0.18 Hz (10.8 CPM) low cutoff filter for
non-integrated measurements will always cause the Dynamix
2500 data collector to go into a long autorange mode. Only use
these filter settings when very low frequency data is required.
TIP
The measurement units cannot be changed after you collect
data for the measurement definition.
Click to use the RSS filter
- Dynamix 2500 Data Collector 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Chapter 3 6
- Setting Up Measurements 6
- Chapter 4 6
- Chapter 5 7
- Optional Extension 9
- Dynamix 2500 Data 10
- Collector and the Emonitor 10
- Software 10
- Software Compatibilities 10
- Document Conventions 10
- Using Online Help 11
- Additional Resources 12
- Safety Information 15
- Collector Kit Parts List 15
- Collector Optional Parts 16
- Parts of the Dynamix 2500 17
- External Connections 19
- POWER /USB/TRIGGER 20
- Using the Headphones 20
- Status Indicators 22
- Strap Attachment 23
- Battery Pack 23
- Check the Battery Level 23
- Battery Maintenance 27
- Calibration 27
- Apply Power to the Data 29
- Installing the USB Drivers 30
- Install USB Drivers 31
- Updating the Operating 34
- 2. Click Next 35
- 4. Click Next 36
- The loader is installed 36
- The installation is complete 36
- 5. Click Close 36
- Module Licensing 40
- Restarting the Data 42
- Collector Main Menu 45
- Change the Display Backlight 47
- Collector Setup Screen 48
- Collector Data Collection 51
- for more information 53
- Setting Up the Dynamix 55
- 2500 Data Collector 55
- Using Memory Cards 64
- Measurement Definition 66
- Measurement Types 67
- Measurement Filters 67
- Advantage of Hardware Filters 68
- Advantage of Software Filters 69
- ESP Filters 70
- High Pass Filters 70
- Order (Magnitude) Filters 71
- Default Filters 72
- RSS Overall 73
- Measurement Units 74
- Setting Up Collection 75
- Specifications 75
- Measurement Input Types 76
- Measurement Window Types 77
- Measurement Resolution 79
- Number and Type of Averages 80
- Orders Track 82
- Setting Up Speed References 83
- Setting Up Measurement 86
- Definitions 86
- Proximity Probe Measurements 87
- Temperature Measurements 93
- Set Up Tri-axial Measurements 102
- Setting Up Alarms, Lists 104
- Lists and the Data Collector 105
- Loading and Unloading 107
- Install ActiveSync Software 108
- 8. Click OK when finished 112
- Advanced Settings dialog box 112
- Loading Lists to the Data 113
- Collector 113
- IMPORTANT 115
- Loading Inspection Codes 116
- Load Frequency Labels 117
- Select the Lists 118
- Unloading Lists from the 121
- Data Collector 121
- 3. Click OK 124
- Quickload Files 127
- Collecting and Reviewing Data 129
- Collecting Route Data 131
- Move through a List 133
- Start Data Collection 135
- Bias Check 136
- Select Inspection Codes 137
- Figure 24 - Spectrum 143
- If you Then 143
- See Review Data on page 164 144
- Exceptions 147
- Collecting Offroute Data 149
- Measurement Description 150
- User screen 152
- Type Description 153
- Parameter Value 153
- Create a User-defined Point 154
- Detection Description 157
- Window Description 158
- Storing Unscheduled Data 159
- Enable smart unscheduled 160
- Changing Display View 161
- Reviewing Data 161
- Review Route Data 162
- Review Offroute Data 162
- Review Data 164
- Table 44 166
- Key Description 166
- Press H Function 166
- Review Waterfall Spectra Data 167
- Capturing Screens 168
- Multi-channel Measurements 169
- Orbit Measurements 170
- Figure 2 - 1X Orbit Plot 171
- Figure 5 - Complex Orbit 173
- Collect Orbit Measurements 178
- View Options 179
- Cross Channel Phase 182
- Measurements 182
- Phase Tables 183
- Adjustments 183
- Emonitor Software 184
- Press F2 (User) to create a 186
- Dual Channel 192
- Select a display format 194
- Magnitude and Phase 196
- Offroute Measurement 196
- Install Optional Extension 205
- Extension Manager 206
- Uninstall an Extension 207
- Manage Extension 209
- The extension modules that 210
- [square brackets] 210
- Numerics 211
- Rockwell Automation Support 218
- Documentation Feedback 218
Relacionado con productos y manuales para Equipo Rockwell-automation 1441-DYN25-Z Dynamix 2500 Data Collector
Equipo Rockwell-automation 937CU-AISTR-DC1 Strain Gauge Converter Installatio Manual de usuario
(48 paginas)
(48 paginas)
Equipo Rockwell-automation 1492-ASPCL3 Commoning Link For Circuit Breakers Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1492-PRINT110_PRINT220 ClearTools User Manual Manual de usuario
(182 paginas)
(182 paginas)
Equipo Rockwell-automation 1441-DYN25-MFRF Frequency Response Function Extens Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation 1492-CM800-LA003 Field Wire Conv. Module for Modic Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1512B MV Controllers, 200/400A Two-High Cabinet, S Manual de usuario
(100 paginas)
(100 paginas)
Equipo Rockwell-automation 1336S_F_E_T_R Transistor,Thyristor (SCR) Replaceme Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 1492 Modicon 800-to-1756 I/O Swing-arm Conversion Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 1203 Splitter Module SG2, SG4, S03 Instructions Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1502 Electrically-Held to Mechanically Latched Con Manual de usuario
(14 paginas)
(14 paginas)
Equipo Rockwell-automation 1492 1771-to-1756 I/O Swing-arm Conversion System Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 931H-T2C1D-DC Active Converter, Thermocouple, Type Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1503F OEM Products - Isolation Switch with Fuse Cl Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales