Rockwell-automation 1771-IFE/C INSTL.INSTRUCTIONS ANALOG INPU Manual de usuario Pagina 8
- Pagina / 16
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Analog Input Module8
Publication
17715.45 - July 1997
Source Ground
-
Unused channels must have their + and
inputs jumpered together and tied to
module common to reduce noise.
1771WG
Field Wiring Arm
Attention: Analog input signals must be within +
14.25V referenced
to module common. If an input channel exceeds this range,
channeltochannel crosstalk can cause invalid input readings and
invalid underrange or overrange bits.
NOTE:
The 1771IFE module does not supply loop power for the input device.
The user must supply loop power for looppowered input devices.
+
–
Channel
1+
Channel 1
Channel 2+
Channel 2
Channel 3+
Channel 3
Channel 4+
Channel 4
Channel 5+
Channel 5
Channel 6+
Channel 6
Channel 7+
Channel 7
Channel 8+
Channel 8
Module Common
Not used
Not used
Not used
Module Common
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Configuring
the module for dif
ferential inputs does not provide isolation.
-T
ie power supply grounds together to
minimize ground loops.
Note:
Refer to transmitter manufacturers
specifications for power supply connections.
+
Power
Supply
2Wire
Transmitter
Power
Supply
2Wire
Transmitter
–
The sensor cable must be shielded. The shield must:
•
extend the length of the cable, but be connected only at the 1771 I/O chassis
•
extend up to the point of termination
Important:
The shield should extend to the termination point, exposing just enough cable to
adequately terminate the inner conductors. Use heat shrink or another suitable
insulation where the wire exits the cable jacket.
Connection
Diagram for 8 Differential Inputs and T
woW
ire T
ransmitters
Source Ground
-
Unused channels must have their + and
inputs jumpered together and tied to
module common to reduce noise.
1771WG
Field Wiring Arm
Attention: Analog input signals must be within +
14.25V referenced
to module common. If an input channel exceeds this range,
channeltochannel crosstalk can cause invalid input readings and
invalid underrange or overrange bits.
NOTE:
The 1771IFE module does not supply loop power for the input device.
The user must supply loop power for looppowered input devices.
+
–
Channel
1+
Channel 1
Channel 2+
Channel 2
Channel 3+
Channel 3
Channel 4+
Channel 4
Channel 5+
Channel 5
Channel 6+
Channel 6
Channel 7+
Channel 7
Channel 8+
Channel 8
Module Common
Not used
Not used
Not used
Module Common
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Configuring
the module for dif
ferential inputs does not provide isolation.
-T
ie power supply grounds together to
minimize ground loops.
Note:
Refer to transmitter manufacturers
specifications for power supply connections.
+
–
The sensor cable must be shielded. The shield must:
•
extend the length of the cable, but be connected only at the 1771 I/O chassis
•
extend up to the point of termination
Important:
The shield should extend to the termination point, exposing just enough cable to
adequately terminate the inner conductors. Use heat shrink or another suitable
insulation where the wire exits the cable jacket.
Power
Supply
4Wire
Transmitter
Power
Supply
4Wire
Transmitter
Connection
Diagram for 8 Differential Inputs and FourW
ire T
ransmitters
- Analog Input Module 1
- Understand Compliance to 2
- European Union Directives 2
- Understand Product 2
- Compatibility 2
- A and B 3
- Simulation 3
- Series C 3
- Application 3
- Set the Configuration 4
- Jumpers and Key the 4
- Backplane Connector 4
- Install the Module and 5
- Field Wiring Arm 5
- Connect Wiring to the 6
- Analog Input Module 7 7
- Ground the Chassis and Module 9
- Configure the Module 10
- an input terminal' 11
- underrange/overrange bits 11
- Interpret Status Indicators 12
- Troubleshooting 13
- Specifications 13
- Publication 14
- 17715.45 - July 1997 14
- Differences Between 16
- Series A, B and C Modules 16
Relacionado con productos y manuales para Equipo Rockwell-automation 1771-IFE/C INSTL.INSTRUCTIONS ANALOG INPU
Equipo Rockwell-automation 1734-IE4C POINT I/O 4 Channel High Density Current Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1738-OE4CM12 ArmorPoint 4-Channel 24V dc Analog Ou Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1769-SM1 Compact I/O to DPI/SCANport Module Manual de usuario
(176 paginas)
(176 paginas)
Equipo Rockwell-automation Logix5000 Controllers ASCII Strings Programming Ma Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation Logix5000 Controllers Common Procedures Programmin Manual de usuario
(1 paginas)
(1 paginas)
Equipo Rockwell-automation 1784-PKTCS ControlNet PCI Scanner Card Installatio Manual de usuario
(70 paginas)
(70 paginas)
Equipo Rockwell-automation 1738-IJM23 ArmorPOINT I/O 5V DC Encoder/Counter Mo Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation 1751 SynchLink Base Block Installation Instruction Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1747-DU501 SLC 5/05 Processors Firmware/Operating Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1775-S4B,D17756.5.3 User Manual SCANNER/MSG HND Manual de usuario
(167 paginas)
(167 paginas)
Equipo Rockwell-automation 1785-ENET USER MANUAL PLC-5 ETHERNET INTERFACE Manual de usuario
(54 paginas)
(54 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales