Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN Manual de usuario Pagina 87
- Pagina / 172
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 520COM-UM003A-EN-E - June 2013 87
Chapter 7
Using Multi-Drive Mode
This chapter provides instructions on how to configure a CompactLogix
controller to use the PowerFlex 520-series drive in Multi-drive mode.
Single-Drive Mode vs.
Multi-Drive Mode
Single-drive mode is a typical network installation, where a single EtherNet/IP
node consists of a single drive with an EtherNet/IP adapter.
Topic Page
Single-Drive Mode vs. Multi-Drive Mode
87
System Wiring 89
Understanding the I/O Image 90
Configuring the RS-485 Network 91
Using Multi-Drive Add-On Profile 91
Multi-Drive Ladder Logic Program for Generic Profile 102
CompactLogix Controller Example Using Generic Profile 103
Multi-Drive Mode Explicit Messaging 111
Additional Information 112
ATTENTION: On PowerFlex 525 drives, support for multi-drive mode using the
25-COMM-E2P Dual-Port adapter is only available on firmware revision 1.004
and later.
ATTENTION: Risk of injury or equipment damage exists. The examples in this
publication are intended solely for purposes of example. There are many
variables and requirements with any application. Rockwell Automation, Inc.
does not assume responsibility or liability (to include intellectual property
liability) for actual use of the examples shown in this publication.
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Overview 7
- Preface Overview 8
- Getting Started 9
- Features 10
- Understanding Parameter 10
- Compatible Products 11
- Required Equipment 11
- Safety Precautions 12
- Quick Start 13
- Chapter 1 Getting Started 14
- Installing the Adapter 15
- Setting the Node Address 16
- Connecting the Adapter to 18
- 00:00:BC:2E:69:F6 21
- Applying Power 22
- ENET LINK 23
- EtherNet/IP 23
- Commissioning the Adapter 24
- Configuring the Adapter 25
- Using the PowerFlex 4-Class 27
- HIM to Access Parameters 27
- Setting the Adapter Node 27
- Using a BOOTP or DHCP 28
- Using Adapter Parameters 31
- Setting the Data Rate 32
- Using Master-Slave Hierarchy 33
- Setting a Fault Action 34
- Changing the Fault Action 35
- Resetting the Adapter 36
- Restoring Adapter 36
- Parameters to Factory 36
- Defaults 36
- Viewing the Adapter Status 37
- Using Parameters 37
- Updating the Adapter 37
- Firmware 37
- Configuring the I/O 39
- CompactLogix Example 40
- Configuring the I/O Chapter 4 41
- Designer 42
- Chapter 4 Configuring the I/O 46
- Controller Input Tags 47
- Controller Output Tags 47
- Logix Designer 50
- ADC and Logix Memory 54
- Monitoring the ADC Progress 55
- Input Image Controller Tags 60
- Output Image Controller Tags 60
- Limitations in Using 62
- MicroLogix 1100/1400 62
- Using the I/O 63
- Understanding the I/O Image 64
- Using Logic Command/Status 65
- Using Reference/Feedback 65
- Using Datalinks 66
- Example Ladder Logic 67
- Program Information 67
- Feedback 68
- Reference 69
- Logix Designer Software 70
- Chapter 5 Using the I/O 72
- Using Explicit Messaging 73
- Explicit Messaging Process 74
- Using Multi-Drive Mode 87
- System Wiring 89
- Configuring the RS-485 91
- Using Multi-Drive Add-On 91
- Differences Found Screen 101
- Multi-Drive Ladder Logic 102
- Program for Generic Profile 102
- CompactLogix Controller 103
- Example Using Generic 103
- Main Routine 104
- Drive 0...4 Control Routines 105
- Drive 0 Control Routine 106
- Drive 1 Control Routine 107
- Drive 2 Control Routine 108
- Drive 3 Control Routine 109
- Drive 4 Control Routine 110
- Multi-Drive Mode Explicit 111
- Messaging 111
- Additional Information 112
- Troubleshooting 115
- PORT Status Indicator 116
- MOD Status Indicator 116
- NET A Status Indicator 116
- NET B Status Indicator 117
- Viewing Adapter Diagnostic 117
- Viewing and Clearing Events 120
- Adapter Events 121
- Specifications 123
- Appendix A Specifications 124
- Adapter Parameters 125
- EtherNet/IP Objects 129
- Identity Object 130
- Instance Attributes 131
- Assembly Object 132
- Register Object 133
- Instances (Multi-Drive) 134
- Class Attributes 135
- Parameter Object 136
- PCCC Object 139
- N-Files 140
- DPI Device Object 142
- DPI Parameter Object 145
- on page 150 147
- Descriptor Attributes 148
- Formulas for Converting 150
- Common Services 150
- Object Specific Services 150
- DPI Fault Object 151
- TCP/IP Interface Object 153
- Ethernet Link Object 155
- Appendix D 157
- Logic Command Word 157
- Logic Status Word 158
- Position Bit Definitions 159
- Glossary 161
- Rockwell Automation Support 172
- Documentation Feedback 172
Relacionado con productos y manuales para Equipo Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN
Equipo Rockwell-automation 140MX-C_F Motor Protection Circuit Breaker Accesso Manual de usuario
(1 paginas)
(1 paginas)
Equipo Rockwell-automation 194E Control and Load Switches 125...315 A, 3 Pole Manual de usuario
(1 paginas)
(1 paginas)
Equipo Rockwell-automation 140U-xxx NFPA 79 Internal Rotary Operating Handle Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 193-ERR E1 PLUS Remote Reset Accessory Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 440T Single Key Slamlock with Electrical Isolation Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 440R Guardmaster Safety Relay GLP Installation Ins Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.196 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales