Rockwell-automation FactoryTalk Historian SE 3.0 UniInt Interface User Manual de usuario Pagina 11
- Pagina / 108
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
UniInt Interface User Manual 5
Standard Parameters
These command-line parameters are used in the every-day running of an interface. This table
does not contain the entire list of parameters supported by UniInt. There are parameters that
are specific to configuring disconnected start-up discussed in the Disconnect Start up section
(page 54) and parameters specific to configuring UniInt Failover discussed in Configuring
UniInt Failover section (page75). None of the parameters are case sensitive. For example,
/ps=ifc is equivalent to /ps=IFC.
Parameter
Description
/AppName=Name
Optional
Default = 1st four
characters of the
interface executable
The /AppName=Name controls the name sent to the
Historian Server in order to establish the PI API trust. Prior to
version 4.1 of UniInt, the interface name was used to establish
the PI API trust with the Historian Server. This limited the
Historian Administrator‟s options when setting up security for
an interface node. There was no way to configure different PI
API trusts for different instances of the interface running on
the same computer. The Historian Administrator is now able to
specify an application name for each instance by using the
/AppName=Name parameter.
The maximum length of the Name is 4 characters. Please
keep in mind when setting up the Trust that the PI API puts an
E at the end of the application name.
The Application Name that is sent to the Historian Server can
be viewed in the Historian Server Message Log immediately
after an interface is started. A message will be written to the
message log stating the connection status for a “process
name”. The “process name” is the application name sent from
the interface.
/dbUniInt=level
Optional
Defualt = 0
The /dbUniInt parameter is used to set a debug level for
debugging UniInt code. level is a 32-bit integer. Setting a
particular bit in level to 1 turns on a particular debug
switch. To turn on every debug switch specify:
/dbUniInt=0xFFFF
level can be specified as either a decimal number or a
hexadecimal number. A 0x must precede hexadecimal
numbers.
The following table lists the sections of code that can provide
debug information and the hexadecimal value that level
must equal in order for that section to output messages.
Multiple sections can output debug messages simultaneously
by adding the values together. For example, both initiailization
and shutdown can be debugged by adding the two level
Values 0x02 and 0x08 together and specifying level as
0x0A.
UniInt Area
Hexadecimal Value
Initialization
0x0002
Shutdown
0x0008
Saving to Historian
0x0010
Control Loop Function
0x0020
- UNIINT INTERFACE USER MANUAL 1
- Table of Contents 3
- Introduction 7
- Running Modes 10
- Informational Parameters 10
- Standard Parameters 11
- is when the 14
- Interface Startup Parameters 20
- /updateinterval=# 20
- What are Historian Points? 21
- Interface Points 21
- Point Attributes 22
- Input Points 28
- Output Points 29
- I/O Rate Points 31
- Performance Points 32
- Performance Summaries 33
- UniInt and PI SDK 33
- “Known Servers” Table 34
- Interface Operation 35
- Historian Point Updates 36
- Exit Handler 36
- Windows Performance Counters 39
- UniInt Performance Counters 41
- directory 44
- Interface Health Points 45
- Interface Point Count 49
- IO Rate 49
- Message Counter 50
- Output Rate 50
- Output Bad Value Rate 50
- Trigger Input Rate 51
- Trigger Input Bad Value Rate 51
- Scan Class Health Tags 51
- Scan Class Scan Time 54
- Operating Systems 55
- Interface 56
- Buffering 56
- Limitations 58
- Outputs 59
- ICU Configuration 61
- Operation 66
- Creation 67
- Validation 68
- Construction 68
- Utilization 69
- Synchronization 70
- Remote Cache Builds 71
- Messages 72
- Configuration Errors 74
- Troubleshooting 76
- 3. Delete the cache files 77
- Configuring UniInt Failover 81
- Data Source Points 82
- Historian Tags 83
- Historian Tag 84
- Description 84
- Steady State Operation 87
- Glossary 88
- Failover ID 89
- Failover Update Interval 89
- Heartbeat Point 89
- Hot Failover 89
- Input Data 90
- Failover Scenarios 91
- Manual Failover 96
- UniInt Failover Scheme 100
- Maximum Data Overlap 103
- Message Logs 105
- Messages on Windows 105
- System Errors and PI Errors 105
- Definition of, 2 107
Relacionado con productos y manuales para Equipo Rockwell-automation FactoryTalk Historian SE 3.0 UniInt Interface User
Equipo Rockwell-automation T8471 Trusted TMR 120V dc Digital Output Module Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation DC2-71, 78, 91, and 98 Drive Fuse Kit Options For Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1440-TB-A XM-940 Dynamic Measurement Terminal Base Manual de usuario
(22 paginas)
(22 paginas)
Equipo Rockwell-automation Logix5000 Control Systems: Connect a PowerFlex 70 Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation T8290 Trusted Output Power Distribution Unit Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation SD3100 DISTRIB PWR SYS SD3100 DC PWR MODULE Manual de usuario
(76 paginas)
(76 paginas)
Equipo Rockwell-automation CEP7-ERR CEP7 Remote Reset Accessory Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation FlexPak Plus, MinPak Plus DC Drive Dynamic Braking Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation CA6-TC420 Sprecher+Schuh CA6 Terminal Cover Kit Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation T8847 Trusted 40 Channel Fire Input Versatile FTA Manual de usuario
(14 paginas)
(14 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.266 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales