Rockwell-automation FactoryTalk Historian SE 3.0 UniInt Interface User Manual de usuario Pagina 16
- Pagina / 108
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Interface Startup Parameters
10
Parameter
Description
the /id parameter (such as /in, /ic, etc) to identify the
copy of an interface. Consult the interface-specific
documentation for more information.
/IOSourceTime
Optional
The /IOSourceTime stands for Initial output source
timestamp. Some interfaces send the current value of the
source tag at start-up. If this parameter is not specified, the
timestamp sent with the initial value is the current Historian
Time. This command-line parameter instructs UniInt to send
the timestamp of the source tag‟s snapshot value to the
interface specific code that handles the actual output.
/logps
Optional
When the /logps parameter is present, the point source for
the interface will be included in the header of the log
messages sent to the pipc.log file.
/logUFOID
Optional
When the /logUFOID parameter is present and the
interface is configured for UniInt failover, the failover ID for the
interface will be included in the header of the log messages
sent to the pipc.log file.
/maxstoptime=
stoptime
Optional
Default = 120 seconds
When an interface receives a signal from the operating
system to shut down, there is a list of clean up functions that
need to be performed. If for some reason the execution of
these functions takes longer than the stoptime, the
interface will shut down without finishing its tasks.
/NoOutputs
Optional
If this parameter is specified, outputs are disabled.
If outputs are disabled, the message
/NoOutputs flag detected. Outputs from
Historian disabled
will be written to the message log when the interface starts.
/perf=interval
Optional
Default = 8 hours
When the percentage of scans that a UniInt-based interface
performs on time drops below 95%, UniInt will print out
performance summaries for each scan class. Performance
summaries are described in the section called “Performance
Summaries.”
UniInt checks whether a performance summary is in order
every interval hours. For example, if /perf=0.025,
UniInt will write performance summaries every 90 seconds if
the percentage of on-time scans is below 95%. The minimum
time between summaries is 60 seconds. Setting /perf=0
disables summaries. If the /perf parameter is omitted, then
UniInt checks whether summaries are in order every 8 hours
by default.
If the inputs for the interface are unsolicited, then performance
summaries should be disabled by setting /perf=0 because
performance summaries are meaningless for unsolicited input
points.
- UNIINT INTERFACE USER MANUAL 1
- Table of Contents 3
- Introduction 7
- Running Modes 10
- Informational Parameters 10
- Standard Parameters 11
- is when the 14
- Interface Startup Parameters 20
- /updateinterval=# 20
- What are Historian Points? 21
- Interface Points 21
- Point Attributes 22
- Input Points 28
- Output Points 29
- I/O Rate Points 31
- Performance Points 32
- Performance Summaries 33
- UniInt and PI SDK 33
- “Known Servers” Table 34
- Interface Operation 35
- Historian Point Updates 36
- Exit Handler 36
- Windows Performance Counters 39
- UniInt Performance Counters 41
- directory 44
- Interface Health Points 45
- Interface Point Count 49
- IO Rate 49
- Message Counter 50
- Output Rate 50
- Output Bad Value Rate 50
- Trigger Input Rate 51
- Trigger Input Bad Value Rate 51
- Scan Class Health Tags 51
- Scan Class Scan Time 54
- Operating Systems 55
- Interface 56
- Buffering 56
- Limitations 58
- Outputs 59
- ICU Configuration 61
- Operation 66
- Creation 67
- Validation 68
- Construction 68
- Utilization 69
- Synchronization 70
- Remote Cache Builds 71
- Messages 72
- Configuration Errors 74
- Troubleshooting 76
- 3. Delete the cache files 77
- Configuring UniInt Failover 81
- Data Source Points 82
- Historian Tags 83
- Historian Tag 84
- Description 84
- Steady State Operation 87
- Glossary 88
- Failover ID 89
- Failover Update Interval 89
- Heartbeat Point 89
- Hot Failover 89
- Input Data 90
- Failover Scenarios 91
- Manual Failover 96
- UniInt Failover Scheme 100
- Maximum Data Overlap 103
- Message Logs 105
- Messages on Windows 105
- System Errors and PI Errors 105
- Definition of, 2 107
Relacionado con productos y manuales para Equipo Rockwell-automation FactoryTalk Historian SE 3.0 UniInt Interface User
Equipo Rockwell-automation T8471 Trusted TMR 120V dc Digital Output Module Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation DC2-71, 78, 91, and 98 Drive Fuse Kit Options For Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1440-TB-A XM-940 Dynamic Measurement Terminal Base Manual de usuario
(22 paginas)
(22 paginas)
Equipo Rockwell-automation Logix5000 Control Systems: Connect a PowerFlex 70 Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation T8290 Trusted Output Power Distribution Unit Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation SD3100 DISTRIB PWR SYS SD3100 DC PWR MODULE Manual de usuario
(76 paginas)
(76 paginas)
Equipo Rockwell-automation CEP7-ERR CEP7 Remote Reset Accessory Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation FlexPak Plus, MinPak Plus DC Drive Dynamic Braking Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation CA6-TC420 Sprecher+Schuh CA6 Terminal Cover Kit Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation T8847 Trusted 40 Channel Fire Input Versatile FTA Manual de usuario
(14 paginas)
(14 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales