Rockwell-automation 20-750-BNETIP BACnet/IP Option Module Manual de usuario Pagina 32
- Pagina / 88
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
32 Rockwell Automation Publication 750COM-UM005B-EN-P - June 2014
Chapter 3 Configuring the Option Module
Setting Web Page Access
By using a web browser to access the IP address set for the option module, you
can view the option module web pages for information about the module, the
drive, and other DPI devices connected to the drive, such as HIMs or converters.
By default, the option module web pages are disabled. To enable the option
module web pages, do the following.
1. Set Device Parameter 26 - [Web Enable] to ‘1’ (Enabled).
2. Reset the option module; see Resetting the Option Module on page 33 so
that the change takes effect.
For more details on the option module web pages, see Chapter 6
, Viewing
Option Module Web Pages.
The option module can be configured to automatically send e-mail messages to
desired addresses when selected drive faults occur and/or are cleared, and/or
when the option module takes a communication or idle fault action.
Bit 0 of Device Parameter 27 - [Web Features] is used to protect the configured
settings for e-mail messaging. By default, settings are not protected and the user
can make changes. To protect the configured settings, set the value of E-mail Cfg
Bit 0 to ‘0’ (Disabled). You can unprotect the configuration by changing Bit 0
back to ‘1’ (Enabled). E-mail messaging will always remain active regardless of
whether or not its settings are protected—unless e-mail messaging was never
configured. For more information about configuring option module e-mail
messaging or to stop e-mail messages, see Configure E-mail Notification Web
Page on page 56.
Bit 0 is the right-most bit. In the example above, it equals ‘1’ (Enabled).
Changes to this parameter take effect immediately. A reset is not required.
Stopped
0.00 Hz
AUTO
F
Edit Web Enable
Disabled 0
0<<1
ESC
▲▼
ENTER
Value Description
0 Disabled (Default)
1 Enabled
Bit Description
0 E-mail Cfg (Default = 1 = Enabled)
1...7 Not Used
AUTO
F
Stopped
0.00 Hz
Edit Web Features
xxxx xxx1
E-mail Cfg
ESC ENTER
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Conventions Used in This 9
- Rockwell Automation 9
- Additional Resources 10
- Getting Started 11
- Features 12
- Understanding Parameter 12
- Compatible Products 13
- Required Equipment 13
- Safety Precautions 15
- Quick Start 16
- Installing the Option Module 17
- Setting the IP Address 18
- Selection Jumper 18
- Connecting the Option 19
- Module to the Drive 19
- Module to the Network 19
- Applying Power 20
- Commissioning the Option 23
- Configuring the Option Module 25
- Using the PowerFlex 20 26
- HIM-A6 or 20-HIM-C6S HIM 26
- Setting the Option Module 26
- Address Using Parameters 26
- Setting the Device Instance 28
- Setting the Device Port 29
- Setting a Fault Action 29
- 0<<4 30
- Setting the Comm Loss Time 31
- Setting Web Page Access 32
- Resetting the Option 33
- Restoring Option Module 34
- Parameters to Factory 34
- Defaults 34
- Viewing the Option Module 35
- Status Using Parameters 35
- Updating the Option 35
- Module Firmware 35
- BACnet Services 37
- Understanding BACnet 38
- Basic Drive Operation on 39
- Supported BACnet Objects 40
- Troubleshooting 43
- PORT Status Indicator 44
- MOD Status Indicator 44
- NET A Status Indicator 45
- Viewing Option Module 45
- Diagnostic Items 45
- Viewing and Clearing 47
- Enabling the Option Module 51
- Web Pages 51
- Viewing the Web Pages 51
- IMPORTANT 52
- Process Display Pop-up 54
- Dialog Box 54
- BACnet/IP Configuration 55
- Web Page 55
- Configure E-mail 56
- Notification Web Page 56
- 3. Click Save Changes 58
- Device Information Pages 59
- Specifications 63
- Environmental 64
- Regulatory Compliance 64
- Option Module Parameters 65
- About Parameter Numbers 66
- How Parameters Are 66
- Organized 66
- Device Parameters 66
- Host Parameters 69
- Reset Required: No 70
- 750-Series Drives 71
- Logic Status Word 72
- Conformance Statement 73
- List all BACnet 74
- Interoperability Building 74
- Blocks Supported 74
- (Annex K) 74
- Segmentation Capability 74
- Standard Object Types 75
- Supported 75
- Data Link Layer Options 76
- Device Address Binding 76
- Networking Options 76
- Network Security Options 76
- Character Sets Supported 76
- Glossary 77
- Rockwell Automation Support 88
- Documentation Feedback 88
Relacionado con productos y manuales para Equipo Rockwell-automation 20-750-BNETIP BACnet/IP Option Module
Equipo Rockwell-automation 284D- ArmorStart Base and Control Module Replaceme Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 20-750-PNET Profinet Single Port Option Module Manual de usuario
(96 paginas)
(96 paginas)
Equipo Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module Manual de usuario
(144 paginas)
(144 paginas)
Equipo Rockwell-automation 445L GuardShield Safe 4 and Safe 4 PAC Safety Ligh Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 160 Supplement-160-NX3 Chassis Mount Series C Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 140U Q, M frame CB Electronic RMS Trip Unit instal Manual de usuario
(14 paginas)
(14 paginas)
Equipo Rockwell-automation 440N SensaGuard Magnetically Coded NonContact Swit Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 193-ERR E1 PLUS Remote Reset Accessory Module Manual de usuario
(6 paginas)
(6 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales