Rockwell-automation 20-750-BNETIP BACnet/IP Option Module Manual de usuario Pagina 35
- Pagina / 88
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 750COM-UM005B-EN-P - June 2014 35
Configuring the Option Module Chapter 3
9. Reset the option module using Device Parameter 03 - [Reset Module] or
by cycling power to the drive so that the restored parameters take effect.
Viewing the Option Module
Status Using Parameters
The following parameter provides information about the status of the option
module. You can view this parameter at any time.
Updating the Option
Module Firmware
The option module firmware can be updated over the network or serially through
a direct connection from a computer to the drive using a 1203-USB or 1203-SSS
serial converter.
When updating firmware over the network, you can use the Allen-Bradley
ControlFLASH software tool, the built-in update capability of DriveExplorer
Lite or Full software, or the built-in update capability of DriveExecutive software.
When updating firmware through a direct serial connection from a computer to a
drive, you can use the same Allen-Bradley software tools described above, or you
can use HyperTerminal software set to the X-modem protocol.
To obtain a firmware update for this option module, go to http://www.ab.com/
support/abdrives/webupdate. This website contains all firmware update files and
associated Release Notes that describe the following items:
• Firmware update enhancements and anomalies
• How to determine the existing firmware revision
• How to update the firmware using ControlFLASH, DriveExplorer, or
DriveExecutive software.
IMPORTANT
When performing a Set Defaults, the drive may detect a conflict
and then not allow this function to occur. If this happens, first
resolve the conflict and then repeat this Set Defaults procedure.
Common reasons for a conflict include a drive running or a
controller (master) in Run mode.
Module Device Parameter Description
02 - [Net Addr Src] Displays the source from which the option module network address
is taken. It is either ’0’ (Parameters) or ‘1’ (Default) which uses the
following defaults:
• IP Address 192.168.0.1
• Subnet Mask 255.255.255.0
• Gateway Address 192.168.0.1
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Conventions Used in This 9
- Rockwell Automation 9
- Additional Resources 10
- Getting Started 11
- Features 12
- Understanding Parameter 12
- Compatible Products 13
- Required Equipment 13
- Safety Precautions 15
- Quick Start 16
- Installing the Option Module 17
- Setting the IP Address 18
- Selection Jumper 18
- Connecting the Option 19
- Module to the Drive 19
- Module to the Network 19
- Applying Power 20
- Commissioning the Option 23
- Configuring the Option Module 25
- Using the PowerFlex 20 26
- HIM-A6 or 20-HIM-C6S HIM 26
- Setting the Option Module 26
- Address Using Parameters 26
- Setting the Device Instance 28
- Setting the Device Port 29
- Setting a Fault Action 29
- 0<<4 30
- Setting the Comm Loss Time 31
- Setting Web Page Access 32
- Resetting the Option 33
- Restoring Option Module 34
- Parameters to Factory 34
- Defaults 34
- Viewing the Option Module 35
- Status Using Parameters 35
- Updating the Option 35
- Module Firmware 35
- BACnet Services 37
- Understanding BACnet 38
- Basic Drive Operation on 39
- Supported BACnet Objects 40
- Troubleshooting 43
- PORT Status Indicator 44
- MOD Status Indicator 44
- NET A Status Indicator 45
- Viewing Option Module 45
- Diagnostic Items 45
- Viewing and Clearing 47
- Enabling the Option Module 51
- Web Pages 51
- Viewing the Web Pages 51
- IMPORTANT 52
- Process Display Pop-up 54
- Dialog Box 54
- BACnet/IP Configuration 55
- Web Page 55
- Configure E-mail 56
- Notification Web Page 56
- 3. Click Save Changes 58
- Device Information Pages 59
- Specifications 63
- Environmental 64
- Regulatory Compliance 64
- Option Module Parameters 65
- About Parameter Numbers 66
- How Parameters Are 66
- Organized 66
- Device Parameters 66
- Host Parameters 69
- Reset Required: No 70
- 750-Series Drives 71
- Logic Status Word 72
- Conformance Statement 73
- List all BACnet 74
- Interoperability Building 74
- Blocks Supported 74
- (Annex K) 74
- Segmentation Capability 74
- Standard Object Types 75
- Supported 75
- Data Link Layer Options 76
- Device Address Binding 76
- Networking Options 76
- Network Security Options 76
- Character Sets Supported 76
- Glossary 77
- Rockwell Automation Support 88
- Documentation Feedback 88
Relacionado con productos y manuales para Equipo Rockwell-automation 20-750-BNETIP BACnet/IP Option Module
Equipo Rockwell-automation 284D- ArmorStart Base and Control Module Replaceme Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 20-750-PNET Profinet Single Port Option Module Manual de usuario
(96 paginas)
(96 paginas)
Equipo Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module Manual de usuario
(144 paginas)
(144 paginas)
Equipo Rockwell-automation 445L GuardShield Safe 4 and Safe 4 PAC Safety Ligh Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 160 Supplement-160-NX3 Chassis Mount Series C Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 140U Q, M frame CB Electronic RMS Trip Unit instal Manual de usuario
(14 paginas)
(14 paginas)
Equipo Rockwell-automation 440N SensaGuard Magnetically Coded NonContact Swit Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 193-ERR E1 PLUS Remote Reset Accessory Module Manual de usuario
(6 paginas)
(6 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales