Rockwell-automation 160 RSI SERIAL COMM MODULE Manual de usuario

FAULTREADYRS232Serial CommCOMMCAT160-RS1SERMADEINU.S.A.160-RS1SerialCommunicationModuleFRN 1.xxUser Manual

2–2 Quick Start for Experienced UsersProceduresStep ActionFor Further InformationRefer to . . .1. Review Attention statements in the Preface.2.Ensure

Chapter3Installation and WiringThis chapter contains information needed to:• Meet the requirements of the EMC and Low Voltage directivesfor CE complia

3–2 Installation and WiringModule Configuration SwitchesThe RS1 Module utilizes a four position DIP switch (see figurebelow) to configure the baud rate,

Installation and Wiring 3–3Setting the Protocol – SW3As shown in the table below, SW3 sets the protocol being used (point-to-point or multi-drop). If

3–4 Installation and WiringModule Installation/RemovalKeypad or Ready/Fault Panel RemovalBefore installing the RS1 Module, it may be necessary to remo

Installation and Wiring 3–5Figure 3.3Communication Module InstallationRemoving the RS1 ModuleIf you need to reconfigure the RS1 Module DIP switches, yo

3–6 Installation and WiringWiring the ConnectorThe examples below can be used as a guide when wiring.Important:Keep communication wiring away from hig

Installation and Wiring 3–7Figure 3.5Wiring the RS1 Connector- continued1Gender specified refers to the cable connectorsRS1 Module9 Pin, Male1, D-Shel

3–8 Installation and WiringConnecting the CommunicationCable to the ModuleFollow these steps to connect your module.1. Verify that the cable/connector

Chapter4Modes of OperationChapter 4 contains the following information:• Powering up the drive with the RS1 Module installed.• The modes of operation

Important User InformationSolid state equipment has operational characteristics differing fromthose of electromechanical equipment. “Safety Guidelines

4–2 Modes of OperationModes of OperationThe RS1 Module has three modes of operation.• Power-up mode• Run mode• Error modePower-up ModeThe following se

Chapter5RS1 Data Table InterfaceThis chapter provides you with the following information:• Supported PCCC commands of the RS1 Module.• RS1 Module Data

5–2 RS1 Data Table InterfaceTable 5.BData Table FormatThe “File Address” section of the data table is divided into eightareas, each having a different

RS1 Data Table Interface 5–34. Logic Command (N41:0). Writing sends a logic command to the drive. The format is:1Presets 0, 1 & 2 are not availabl

5–4 RS1 Data Table Interface6. Reference Command (N41:1) Writing sends a speed referenceto the 160 drive. This is a scaled speed reference from 0 to 3

Chapter6Parameter DescriptionsThis chapter provides a listing and description of the RS1 Parameters.Important:Refer to your 160 User Manual for drive

6–2 Parameter Descriptions110 10 Read/Write [EPROM BAUD]The baud rate used when SW1 & SW2 are set to “On” (EPROM Mode).1 = 1200 Baud2 = 2400 Baud3

Parameter Descriptions 6–3130 30 Read [DIP Switches]Displays the current DIP switch settings.0 to 0xF0 to 150000131 31 Read [Actual Speed]Returns spee

6–4 Parameter DescriptionsEnd of Chapter 6

Chapter7Using the RS1 Module withDriveExplorer™ SoftwareThe purpose of this chapter is to provide an overview of the stepsneeded to use the Bulletin 9

Table of ContentsPrefaceUsing This Manual Who Should Use This Manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p–iConventions

7–2 Using the RS1 Module with DriveExplorer™ SoftwareSetting Baud Rates andConfiguring theCommunications Port1. Before proceeding, the RS1 Module baud

Using the RS1 Module with DriveExplorer™ Software 7–3Uploading Editable ParametersIt is possible to upload editable parameters and their values (inint

7–4 Using the RS1 Module with DriveExplorer™ SoftwareEnd of Chapter 7

Chapter8Using the RS1 Module with aProgrammable ControllerThis chapter provides an overview of the steps needed to use the RS1Module with a MicroLogix

8–2 Using the RS1 Module with a Programmable ControllerSetting the Drive to EnableNetwork ControlThe 160 drive must be configured to accept logic and s

Using the RS1 Module with a Programmable Controller 8–3Program the LadderThe example ladder program in Figure 8.2 demonstrates writing aLogic Command

8–4 Using the RS1 Module with a Programmable ControllerFigure 8.2Writing Logic Command and Reading Logic StatusReading and WritingParametersReading or

Using the RS1 Module with a Programmable Controller 8–5You can read or write RS1 Module parameters through location N10or N13. For location N10, the R

8–6 Using the RS1 Module with a Programmable ControllerFigure 8.4Reading and Writing Drive ParametersLAD 5 - PARAMETER --- Total Rungs in File = 5Para

Chapter9TroubleshootingThe purpose of this chapter is to help you troubleshoot your RS1Module.LED Indicators andTroubleshootingThe RS1 Status LEDs can

toc–ii Table of ContentsChapter 7Using the RS1 Module withDriveExplorer™ SoftwareRequired Items. . . . . . . . . . . . . . . . . . . . . . . . . . . .

9–2 TroubleshootingREADY LEDThe green READY LED will illuminate whenever the RS1 Module isconnected to the drive and power is applied.COMM LEDThe COMM

Troubleshooting 9–3Table 9.B (continued)160 Drive1 Fault Codes1Refer to the160 User Manualfor the most current fault code information.Table 9.CRS1 Fau

9–4 TroubleshootingEnd of Chapter 9

AppendixASpecificationsElectricalSupply Voltage Supplied by DrivePower Consumption 1.25 Watts maximumEnvironmentalAmbient TemperatureOperating 0 to 50°

A–2 SpecificationsEnd of Appendix A

AppendixBRS1 Module CompatibilityThe 160-RS1 Module has been tested and found to be compatiblewith the following Allen-Bradley products:• MicroLogix 1

B–2 RS1 Module CompatibilityEnd of Appendix B

IndexBBaud Rate, Setting, 3–2BCC Checksum, 3–3CCabling, 3–6CE Compliance, 3–1Checksum ModeSetting, 3–3CRC Checksum, 3–3DData Table Interface, 5–1Data

I–2 IndexNotes

PrefaceUsing This ManualThe purpose of this manual is to provide you with the necessaryinformation to apply the Bulletin 160-RS1 Communication Module.

Publication 0160-5.14 – March, 1999 P/N 189177 (02)Supersedes October, 1998 Copyright 1999 Rockwell International Corporation. All rights reserved. Pr

p–ii PrefaceReference ManualsThe following documents contain additional information concerningAllen-Bradley products. To obtain a copy, contact your l

Chapter1Product OverviewThis chapter contains the following information:• The physical layout of the module.• Location of configuration switches.• Over

1–2 Product OverviewConfiguration DIP SwitchesThe Communication Module has one four position DIP switch forsetting the baud rate, protocol and checksum

Chapter2Quick Start for Experienced UsersThis chapter can help you start using the RS1 CommunicationModule. If you have installed or configured a netwo