Rockwell-automation 1794-APBDPV1 FLEX I/O PROFIBUS Adapter User Manual Manual de usuario Pagina 41
- Pagina / 153
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Publication 1794-UM064B-EN-P - May 2014
Communicate With Your Module 29
1794-IR8 Word/Bit Descriptions
Word Decimal Bit Definition
Read Word 0 00…15 (00…17) Reserved
Read Word 1 00…15 (00…17) Channel 0 Input data
Read Word 2 00…15 (00…17) Channel 1 Input data
Read Word 3 00…15 (00…17) Channel 2 Input data
Read Word 4 00…15 (00…17) Channel 3 Input data
Read Word 5 00…15 (00…17) Channel 4 Input data
Read Word 6 00…15 (00…17) Channel 5 Input data
Read Word 7 00…15 (00…17) Channel 6 Input data
Read Word 8 00…15 (00…17) Channel 7 Input data
Read Word 9 00…07 Underrange bits – these bits are set if the input signal is below the input
channel’s minimum range.
08…15 (10…17) Overrrange bits – these bits are set if 1), the input signal is above the
input channel’s maximum range, or 2), an open detector is detected.
Read Word 10 00…01 Not used – set to 0
02 Reserved
03 Power Up bit – this bit is set (1) until configuration data is received by the
module.
04…06 Critical Error bits – If these bits are anything other than all zeroes, return
the module to the factory for repair.
07 Unused – set to 0
08 (10) Calibration Out of Range bit – set to 1 if a reference signal is out of
range during calibration.
09 (11) Calibration Done bit – set to 1 after an initiated calibration cycle is
complete.
10 (12) Calibration Bad bit – set to 1 if the channel has not had a valid
calibration.
11…15 (13…17) Unused – set to 0.
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- Chapter 1 4
- Table of Contents 5
- Table of Contents vii 7
- Who Should Use this 9
- Purpose of this Manual 9
- Related Documentation 10
- Common Techniques Used 11
- APBDPV1 Module 13
- Purpose of the FLEX I/O 14
- PROFIBUS 14
- APBDPV1 Adapter 14
- Differences Between APB 14
- PROFIBUS APBDPV1 15
- Adapter Components 15
- Mount and Remove 16
- Your System 16
- Optional Accessories 17
- Mounting Kit (1794-NM1) 18
- Mounting Dimensions and 19
- Spacing Requirements 19
- Communicate With Your Module 21
- Polled I/O Structure 22
- Input Status Word Bits 23
- I/O Module Fault 23
- Map Data into the Image 24
- FT for all 27
- Channels 27
- Chx SS Config 35
- 1794-IE4XOE2 Memory Map 37
- 1794-IR8 Memory Map 40
- 1794-IT8 Read and Write Words 44
- 1794-IT8 Word/Bit Description 46
- Setting the Input Filter 56
- Configure Your Input Channels 66
- Setting the Input Filters 67
- calibration 70
- Read Word 9 76
- 3210765411 10 9 815 14 13 12 79
- 32 10765411 10 9 815 79
- 14 13 12 79
- Defaults 80
- The DP Physical Layer 83
- Cabling and Equipment 84
- Required for Line A Type 84
- Required for Line B Type 85
- Connect the Adapter to the 86
- D-Shell Pin Assignment 87
- Terminate the Network 88
- Communication 91
- Enter User Parameter Data 92
- Auto Configure Format 93
- Condensed Format 93
- User Parameter Example 95
- Full Format 96
- Enter Check Configuration 98
- Adapter Status Word 99
- Chapter Summary 101
- PROFIBUS Module 103
- View status from the 104
- Master’s Configuration 104
- Software 104
- Apply FLEX I/O Modules 107
- Classification 108
- Define the Area 108
- Select Protection 109
- Method(s) 109
- Match Field Devices 109
- Module source voltage=17V 110
- Module sense 110
- Specifications 113
- Environmental Specifications 114
- Certifications 114
- 104 Specifications 116
- Device Data Base (GSD) File 117
- EndModule 118
- Teaching GSD Entry 119
- Non-EDT Module Teaching Entry 120
- I/O Profile: 121
- EDT Modules Teaching Entry 124
- Teach an I/O Module to 127
- Work with 1794-APBDPV1 127
- Appendix 134
- Overview 134
- Message Structure 134
- Burst Mode (not supported) 135
- Start Character 136
- HART Address 136
- HART Command 136
- Byte Count 137
- Check Byte 137
- Response Code 137
- HART Field Device Error Codes 138
- Universal Commands 139
- Common Practice Commands 140
- Numerics 148
- 2 Index 149
- Index 3 150
- 4 Index 151
- Rockwell Automation Support 153
- Documentation Feedback 153
Relacionado con productos y manuales para Equipo Rockwell-automation 1794-APBDPV1 FLEX I/O PROFIBUS Adapter User Manual
Equipo Rockwell-automation 6181X-15xxxxxxx VersaView 6181X-IN001B-MU-P Manual de usuario
(104 paginas)
(104 paginas)
Equipo Rockwell-automation 57C620 AutoMax Programming Executive Version 3.8 Manual de usuario
(298 paginas)
(298 paginas)
Equipo Rockwell-automation 2711-NP3 Panel Mounting Studs for PanelView 1400 T Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 2092-DAx Ultra1500 Host Commands for Serial Commun Manual de usuario
(70 paginas)
(70 paginas)
Equipo Rockwell-automation 8520-OM Offline Development System User Manual Manual de usuario
(100 paginas)
(100 paginas)
Equipo Rockwell-automation 1798-OB8E FlexArmor 24V dc Sourcing Output Modules Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation CENTERLINE MCC Hinge Assembly Instruction for 1/2 Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 7000 PowerFlex Medium Voltage Air-Cooled (B Frame) Manual de usuario
(96 paginas)
(96 paginas)
Equipo Rockwell-automation 2711P-RAK12e Adapter Kit for PanelView 1200/1200E/ Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 6159 Industrial 17 inch CRT Monitors, Series B Manual de usuario
(36 paginas)
(36 paginas)
Equipo Rockwell-automation 2705 RediSTATION Operator Interface User Manual Manual de usuario
(64 paginas)
(64 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales