Rockwell-automation 2706-LSW DL40 PLUS OFFLINE PROG.SFTWR.USER MANUAL Manual de usuario Pagina 98
- Pagina / 149
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5–11Downloading/Uploading Message Files
Publication 2706-6.2
!
ATTENTION:Before the upload begins, you will see one of
the following warnings. Which one you see depends on the
type and access settings of your DH+ or Ethernet hardware
device.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
DH+ Network Access is set to Local.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
DH+ Network Access is set to Remote (Bridge)
– Local Address is __.
– Remote Bridge Address is __.
Note: Be sure the selected communication file has the
correct address parameters, and change them if
necessary before continuing.
- Dataliner DL40 Plus 1
- Offline Programming 1
- Software 1
- Allen-Bradley 1
- Important User 2
- Information 2
- 3
- Offline Operating Modes 4
- Downloading/Uploading 4
- Message Files 4
- Using this Manual 6
- Conventions Used 7
- Related Publications 7
- Overview of the DL40 Plus 8
- RS-485/RS-232 Communications 9
- Message Support 10
- Programming Features 11
- Offline Programming Software 12
- 1–6 Overview of the DL40 Plus 13
- 1–7Overview of the DL40 Plus 14
- 1–8 Overview of the DL40 Plus 15
- 1–9Overview of the DL40 Plus 16
- Operating Modes 18
- Special Messages 19
- Controller Support 20
- 2706–LV2R 22
- Available Catalog Numbers 22
- Installing the Software 23
- Installed Files 24
- Memory Requirements 24
- Memory Management 25
- Installation 25
- Basic Installation 26
- (without PassThrough) 26
- Software Installation 27
- 2–6 Installing the Software 28
- DTL_KT.EXE – CFG_DF1.EXE 28
- DTL_DF1.EXE – RNASTR.EXE 28
- CFG_KT.EXE – RNA.EXE 28
- 2–7Installing the Software 29
- Create CFG_KT.INI File 30
- 2–9Installing the Software 31
- 2–10 Installing the Software 32
- Installing the Software for 33
- Ethernet PLC PassThrough 33
- Restart Your PC 34
- Configure Your PLC 34
- Starting the Program 35
- Establishing Initial 35
- Non–networked 35
- Navigating the Software 36
- Getting Help 38
- Setup Menu 39
- Setting Time & Date 40
- Menu Control Keys 41
- Shortcut Keys 41
- Exiting the Software 42
- Creating Message Files 43
- Develop Menu 44
- 4–3Creating Message Files 45
- File Selections Screen 46
- Create New File Window 47
- Data Path Directory Window 48
- Develop Screen Menu 49
- Messages Menu 50
- Edit Message Screen 51
- Message Text Window 52
- Any alphabetic or numeric key 53
- More About Variables 54
- 4–14 Creating Message Files 56
- 4–15Creating Message Files 57
- Create New Message 58
- Copy Messages Screen 59
- Delete Message Screen 61
- Renumber Messages Screen 62
- Text Search Screen 64
- Modify Message Attributes 66
- 4–27Creating Message Files 69
- • any Special Message runs 70
- 4–29Creating Message Files 71
- 4–31Creating Message Files 73
- For DL10 or DL20 For DL50 73
- Message Attribute Default 74
- 4–33Creating Message Files 75
- Options Menu 76
- Special Keys 77
- Ports Menu 78
- Verify Menu 81
- Communications via RS–485 83
- Communications via RS–232 84
- 4–43Creating Message Files 85
- Message Verification Window 85
- To test message on a 85
- Device Menu 86
- Downloading/Uploading Message 88
- Transfer Menu 89
- Downloading a File using 90
- RS-232 or RS-485 90
- Select File screen 92
- Uploading a File 93
- Remote I/O (PassThrough) 95
- Uploading a File using 97
- Selecting a Hardware Device 100
- Publication 2706-6.2 101
- Modifying an Existing 103
- Communications File 103
- Sending the Time and Date to 104
- Writing a File to Tape 105
- Drive:\Root\Subdir 106
- Reading a File from Tape 107
- Getting Reports 108
- Reports Menu 109
- 6–3Getting Reports 110
- Select File Submenu 111
- Configure Ports Submenu 112
- Starting the Print Job 113
- Managing Message Files 114
- Files Menu 115
- Select Files Menu 116
- File Selections/File Picks 117
- Copy File(s) 118
- Delete File(s) 119
- Rename File(s) 119
- Convert DL20 File(s) 120
- Converting single files 121
- Converting multiple files 121
- Message Display Worksheets 122
- Message Display WorksheetsA–2 123
- 124
- 2706-NC14 125
- 2706-NC15 125
- DL40 to Allen-Bradley 126
- 1770-SA or -SB Tape 126
- Recorder 126
- CablesB–4 127
- ASCII Character Sets 128
- Extended ASCII Character Set 129
- Cyrillic Character Set 130
- Accessing Cyrillic Characters 131
- International Character Set 132
- PLC-5 Data Pass–Through 133
- • Series D or greater DL40 134
- System Requirements 134
- Communications 135
- File Setup 135
- Downloading Files 136
- Uploading Files 136
- Download to DL40 137
- (Remote I/O) Submenu 137
- Upload from DL40 137
- (Remote I/O Submenu) 137
- Creating a New 138
- Modifying Existing 139
- Communication Files 139
- Setup Information 140
- PLC-5 Data Pass–Through D–9 141
- PLC-5 Data Pass–ThroughD–10 142
- Publication 2706–6.2 144
- Worldwide representation 149
Relacionado con productos y manuales para Equipo Rockwell-automation 2706-LSW DL40 PLUS OFFLINE PROG.SFTWR.USER MANUAL
Equipo Rockwell-automation 2100 Receiving, Handling, and Storing MCCs Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 6185-F RAC6185 Industrial Flat Panel Monitors Quic Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 6180 Data Storage Drives (for 6180 Industrial Comp Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 6180 Keypad Configuration Utility Floppy Disk Driv Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 2100H-UNTLKx Replacing the Unit Interlock for CENT Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 57C421B Pulsetach Input Module/DCS 5000/AutoMax Manual de usuario
(70 paginas)
(70 paginas)
Equipo Rockwell-automation 8510SA-CMBC AC Spindle Drive Connector Kits Instru Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation VersaView 1200P Integrated Display Computers for H Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 2090-DA-BAT2 Low-profile Connector Kit for I/O and Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1799-OQ10X Embedded I/O Expansion Board with 10 Ou Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 2097-PGMR Memory Module Programmer Quick Start Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 2727-T7P30D1Fxx MobileView Tablet T750 Quick Start Manual de usuario
(100 paginas)
(100 paginas)
Equipo Rockwell-automation 8720MC 8720MC Regenerative Power Supply User Manua Manual de usuario
(136 paginas)
(136 paginas)
Equipo Rockwell-automation 2711P-RAT12E Adapter Kit for PanelView 1400eTouch Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2098-DSD-xxx Ultra3000 Host Commands for Serial In Manual de usuario
(176 paginas)
(176 paginas)
Equipo Rockwell-automation 2100 CENTERLINE Motor Control Center (MCC) Units w Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales