Rockwell-automation 150 MNL/SMC DIALOG+/APP-PROD GUIDE Manual de usuario Pagina 56
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SMC Dialog Plus Smart Motor Controller
3-19
Control Options
The SMC Dialog Plus controller offers a variety of unique control
options that provide enhanced motor starting and stopping
capabilities. Please note that the options are mutually exclusive and
must be specified at the time of order entry.
• Soft Stop
• Pump Control
• Preset Slow Speed
•SMB Smart Motor Braking
• Accu-Stop/Slow Speed with Braking
Soft Stop Option
The Soft Stop option can be used in applications requiring an
extended coast-to-rest. The voltage ramp down time is use
adjustable from 0 to 60 seconds. The Soft Stop time is adjusted
independently from the start time. The load will stop when the
voltage drops to a point where the load torque is greater than th
motor torque.
Figure 3.16 Soft Stop Option
Start Run Soft Stop
Coast-to-rest
Soft
Stop
Kickstart
Initial
Torque
100%
Percent
Voltage
Time (seconds)
!
ATTENTION: Soft Stop is not intended to be used as
an emergency stop. Refer to the applicable standards for
emergency stop requirements
- Application 1
- Please Read! 2
- Important User 2
- Information 2
- Table of Contents 3
- SMC Controllers 8
- Chapter 1 9
- Modes of Operation 10
- Adjustments 11
- Features 11
- Wiring Diagrams 12
- Suitable Replacement 14
- Applications 14
- Applications (cont.) 15
- SMC-2 Smart Motor Controller 20
- Modes of Operation (cont.) 21
- Current Limit Level 24
- Time Select 24
- Adjustments (cont.) 25
- Wiring Diagram 26
- Soft Stop Option 27
- Options (cont.) 29
- Chapter 3 38
- Starting Methods 39
- Current Limit Start 40
- Dual Ramp Start 40
- Starting Methods (cont.) 41
- Electronic Overload 42
- Built-in Communication Port 42
- Features (cont.) 43
- Phase Rebalance 44
- Metering 44
- Fault Indication 44
- Control Terminal Description 46
- Typical Wiring Diagrams 52
- (without options) 52
- (without options) (cont.) 55
- Control Options 56
- Control Options (cont.) 57
- Pump Control Option 60
- Stopping follows: 62
- Preset Slow Speed Option 64
- Speed Option follows: 66
- Customer supplied 70
- Smart Motor 72
- Accu-Stop Option 74
- Capability 80
- Plus Controller 83
- Tow Chain 93
- Exhaust Intake 95
- 1-1/2 HP 96
- 480 Volts 102
- Centrifuge 102
- Gearbox Motor 102
- Gearbox 103
- 575 Volts 104
- 240 Volts 109
- Bundle Bundle 113
- Windshields 114
- 230 Volts 116
- Motor Motor 116
- Die Die 116
- ~~~~~~~~~~~~~~~~~ 122
- Application Considerations 125
- Use of Protective Modules 126
- Current Limit Fuses 127
- Motor Overload Protection 128
- Stall Protection and 129
- Jam Detection 129
- Built-in SCANport 129
- Communications 129
- Power Factor Capacitors 130
- Multi-motor Applications 132
- Part Winding 133
- Wound Rotor 133
- Synchronous 133
- Altitude De-rating 134
- Isolation Contactor 134
- SMC Dialog Plus Controller 135
- Winding Heater 137
- Motor Torque Capabilities 138
- Controller Options 138
- Accu-Stop 139
- Energy Saver Operation 139
- Energy Saver (cont.) 140
- Application Requirements 141
- Preliminary Estimates 141
- Chapter 6 143
- Mining and Metals 144
- Food Processing 145
- Pulp and Paper 146
- Petrochemical 147
- OEM Specialty Machine 149
- Lumber and Wood Products 150
- Water/Wastewater 151
- Treatment and Municipalities 151
- Design Philosophy 152
- Reduced Voltage Starting 154
- Reduced Voltage 155
- Design B Motors 156
- Reduced Voltage (cont.) 157
- Solid-state 159
- Chapter 9 161
- Solid-state Starters 162
- Using SCRs (cont.) 162
- Reference 163
- Torque and Horsepower (cont.) 164
- Locked-Rotor Torque (LRT) 165
- Pull-Up Torque (PUT) 165
- Breakdown Torque (BT) 165
- Motor Output for 169
- NEMA Design Designations 169
- Polyphase 1–500 HP 169
- Polyphase 1–500 HP (cont.) 170
- Calculating Torque 173
- (Acceleration Torque 173
- Required for Rotating Motion) 173
- ---------------------------= 174
- -----------= 174
- Torque Formulas 175
- AC Motor Formulas 176
- Torque Characteristics on 177
- Common Applications 177
- Common Applications (cont.) 178
- Electrical Formulas 179
- Calculating Motor Amperes 180
- Other Formulas 181
- Engineering Constants 181
- Engineering Constants (cont.) 182
- Conversion Factors 185
- Conversion Factors (cont.) 186
- ---------------------= 187
- Glossary 188
- Glossary-2 189
- Glossary-3 190
- Glossary-4 191
- Glossary-5 192
- Glossary-6 193
- Glossary-7 194
- Glossary-8 195
- Glossary-9 196
- Glossary-10 197
- Glossary-11 198
- Glossary-12 199
- Glossary-13 200
- Glossary-14 201
Relacionado con productos y manuales para Equipo Rockwell-automation 150 MNL/SMC DIALOG+/APP-PROD GUIDE
Equipo Rockwell-automation 140U-M-NVMxxx NFPA 79 Internal Rotary Operating NF Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 440H Sprite 3 Miniature Hinge Operating Interlock Manual de usuario
(1 paginas)
(1 paginas)
Equipo Rockwell-automation 440T Prosafe Boltlock Solenoid Locked with electri Manual de usuario
(4 paginas)
(4 paginas)
(3 paginas)
Equipo Rockwell-automation 509 Full Voltage Starter - Size 8 (Series B Constr Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation 847T 2 in. Diameter Solid Shaft Incremental Encode Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 440S Sigma Series 615 Group I/Limit Switches Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 500LG Electrically Held Lighting Contactor - Coil Manual de usuario
(1 paginas)
(1 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales