Rockwell-automation 1794-OB16D FLEX I/O Diagnostic Modules User Manual Manual de usuario Pagina 110
- Pagina / 132
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Publication 1794-UM061A-EN-P - July 2006
108 Interpret the Indicators
Diagnostic Functions for the 1794-OB16D
Diagnostic Functions for the 1794-OB16D
ATTENTION
Each unused output port requires a dummy resistor
(20 KΩ +
10%, 1/8 W) to mask the channel diagnostic
function.
Ext.
Power
Wiring Output
Status
Channel LED
Status
Open Wire
Error Bit
Short
Error Bit
Rev. Error
Bit
Module Error
Bit/LED
OFF Open Off Off 0 0 0 0/OFF
On Off 0 0 0 0/OFF
Short Off Off 0 0 0 0/OFF
On Off 0 0 0 0/OFF
Normal Off Off 0 0 0 0/OFF
On Off 0 0 0 0/OFF
ON Open Off
RED 1001/RED
On
YEL 0 0 0 0/OFF
Short Off Off 0 0 0 0/OFF
On
RED 0 101/RED
Normal Off Off 0 0 0 0/OFF
On
YEL 0 0 0 0/OFF
REV Open Off Off 0 0
1 1/RED
On Off 0 0
1 1/RED
Short Off Off 0 0
1 1/RED
On Off 0 0
1 1/RED
Normal Off Off 0 0
1 1/RED
On Off 0 0
1 1/RED
The module monitors each output channel. It turns on the channel red indicator and sets (1) the error bit when 1) the module detects a
short circuit (the output signal is active at a channel and the corresponding output voltage is low), and 2) the module detects an open wire
(the output signal is inactive at a channel and the corresponding output voltage is high).
- FLEX I/O Diagnostic Modules 1
- Important User Information 2
- Table of Contents 3
- Table of Contents iv 4
- Appendix A 5
- Appendix B 5
- Digital Modules 5
- Table of Contents vi 6
- Purpose of This Manual 7
- Important Warnings and 7
- Cautions 7
- Hazardous Location approved 9
- Related Products and 10
- Documentation 10
- Preface 9 11
- 10 Preface 12
- Preface 11 13
- 12 Preface 14
- Overview 15
- Network Compatibility 16
- Output Module 18
- Base Units) 20
- Introduction 21
- About the 1794-IB16D 21
- Diagnostic Input Module 21
- Input Channels 0-15 22
- Diagnostic Fault Detection 23
- Indicator Status 25
- Information 25
- Module Limitations 26
- Unused Sensor Power Ports 27
- Configure Your Diagnostic 28
- Input Module 28
- About the 1794-OB16D 29
- Diagnostic Output Module 29
- (1794-TB3 shown) 30
- Module Protection 32
- Functions 32
- Indicator Status Information 33
- Configure Your Output 34
- Diagnostic Module 34
- Remote I/O Network 35
- Add a 1756-DHRIO Module 36
- ATTENTION 38
- Add a 1794 Remote Adapter 39
- Configure Digital Modules 42
- Create a Block Transfer 44
- (Read or Write) Message 44
- Instruction 44
- Ladder Logic Examples 48
- DeviceNet Network 49
- Bandwidth 50
- Determine the Address of 54
- DeviceNet Data 54
- Tally Memory 56
- Requirements 56
- Configuration 57
- Offline 57
- Set the Address of the 58
- Select a 61
- Communication Format 61
- Ownership 66
- Add Local and Remote 67
- ControlNet Modules 67
- Add Distributed I/O 68
- Download the Program to 70
- Configure the 1794-ACN15 71
- Schedule I/O Module 72
- Connections 72
- 6. Click OK 73
- File and Save 73
- Access Module Data via 77
- Change Configuration Data 79
- EtherNet/IP Network 83
- Set Up the Hardware 84
- Select a Requested Packet 84
- Interval (RPI) 84
- Select a Communication 85
- Select a Remote Adapter 89
- Access Distributed I/O 93
- General Information About 95
- IP Addresses 95
- Assigning Network 96
- Parameters via the 96
- BOOTP/DHCP Utility 96
- Using Other Methods to 99
- Assign Network 99
- Parameters 99
- Duplicate IP Address 102
- Detection 102
- Duplicate detection scenarios 103
- IP Address Swapping 104
- Interpret the Indicators 105
- Functional Details 106
- 1794-IB16D Diagnostic 106
- For 3-wire sensors: 107
- 1794-OB16D Diagnostic 109
- (20 KΩ + 110
- Appendix 111
- Find Your Module 111
- *Fuse on 1794-TBNF only 113
- * Fuse on 1794-TBNF only 114
- Flexbus Interface 117
- 1794-OW8 Relay Output Module 126
- 126 Index 128
- How Are We Doing? 129
- BUSINESS REPLY MAIL 130
- Rockwell Automation 132
Relacionado con productos y manuales para Equipo Rockwell-automation 1794-OB16D FLEX I/O Diagnostic Modules User Manual
Equipo Rockwell-automation 2711P-RAT12E2 Adapter Kit for PanelView 1200/1200E Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 45C67 Dual Output Module/AutoMate/AutoMax/DCS Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2711-NP2 Mounting Clips for PanelView 600, 900, 10 Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 2706-LV2S_LV4S DL40 PLUS SLAVE USER MANUAL Manual de usuario
(60 paginas)
(60 paginas)
Equipo Rockwell-automation 61C516 AutoMax/AutoMate 24VAC/DC Input Module Manual de usuario
(38 paginas)
(38 paginas)
Equipo Rockwell-automation 2706-F11J_F11JC_F21J_F21JC DL50 INSTALLATION MANUA Manual de usuario
(135 paginas)
(135 paginas)
Equipo Rockwell-automation 2711P-RTFC Mounting Levers for PanelView Plus 400 Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 9323-PA2E APS SLC 500 Import/Export Utility User M Manual de usuario
(110 paginas)
(110 paginas)
Equipo Rockwell-automation 2100 Connecting a CENTERLINE Motor Control Center Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 61C350 2-In/2-Out 0-10 Volt Analog Rail Module Manual de usuario
(48 paginas)
(48 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.290 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales