Rockwell-automation 1794-OB16D FLEX I/O Diagnostic Modules User Manual Manual de usuario Pagina 49
- Pagina / 132
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
47 Publication 1794-UM061A-EN-P - July 2006
Chapter
5
Configure FLEX I/O Digital Modules on a
DeviceNet Network
How to Use This Chapter
This chapter provides basic information on how to use a 1794-ADN FLEX
I/O adapter to connect 1794 FLEX I/O digital modules to a DeviceNet
network.
Use RSNetWorx for DeviceNet software to add the 1794-ADN DeviceNet
adapter and FLEX I/O modules on a DeviceNet network.
To use the FLEX I/O adapter, cat. no. 1794-ADN:
Topic See Page
How to Use This Chapter 47
Add the Scanner to the I/O Configuration of
the Controller Using RSLogix 5000 Software
48
Determine the Address of DeviceNet Data 52
Tally Memory Requirements 54
If You Configure the Adapter Offline 55
Set the Address of the Adapter 56
Step: Page:
❑ Tally Memory Requirements 5-54
❑ As an option, give each module its own memory location (DINTs)
within the scanner. This may make your programming easier. Assign
one address for the 1794-ADN and all the modules that you connect to
it.
5-54
❑ If You Configure the Adapter Offline 5-55
❑ Set the Address of the Adapter 5-56
- FLEX I/O Diagnostic Modules 1
- Important User Information 2
- Table of Contents 3
- Table of Contents iv 4
- Appendix A 5
- Appendix B 5
- Digital Modules 5
- Table of Contents vi 6
- Purpose of This Manual 7
- Important Warnings and 7
- Cautions 7
- Hazardous Location approved 9
- Related Products and 10
- Documentation 10
- Preface 9 11
- 10 Preface 12
- Preface 11 13
- 12 Preface 14
- Overview 15
- Network Compatibility 16
- Output Module 18
- Base Units) 20
- Introduction 21
- About the 1794-IB16D 21
- Diagnostic Input Module 21
- Input Channels 0-15 22
- Diagnostic Fault Detection 23
- Indicator Status 25
- Information 25
- Module Limitations 26
- Unused Sensor Power Ports 27
- Configure Your Diagnostic 28
- Input Module 28
- About the 1794-OB16D 29
- Diagnostic Output Module 29
- (1794-TB3 shown) 30
- Module Protection 32
- Functions 32
- Indicator Status Information 33
- Configure Your Output 34
- Diagnostic Module 34
- Remote I/O Network 35
- Add a 1756-DHRIO Module 36
- ATTENTION 38
- Add a 1794 Remote Adapter 39
- Configure Digital Modules 42
- Create a Block Transfer 44
- (Read or Write) Message 44
- Instruction 44
- Ladder Logic Examples 48
- DeviceNet Network 49
- Bandwidth 50
- Determine the Address of 54
- DeviceNet Data 54
- Tally Memory 56
- Requirements 56
- Configuration 57
- Offline 57
- Set the Address of the 58
- Select a 61
- Communication Format 61
- Ownership 66
- Add Local and Remote 67
- ControlNet Modules 67
- Add Distributed I/O 68
- Download the Program to 70
- Configure the 1794-ACN15 71
- Schedule I/O Module 72
- Connections 72
- 6. Click OK 73
- File and Save 73
- Access Module Data via 77
- Change Configuration Data 79
- EtherNet/IP Network 83
- Set Up the Hardware 84
- Select a Requested Packet 84
- Interval (RPI) 84
- Select a Communication 85
- Select a Remote Adapter 89
- Access Distributed I/O 93
- General Information About 95
- IP Addresses 95
- Assigning Network 96
- Parameters via the 96
- BOOTP/DHCP Utility 96
- Using Other Methods to 99
- Assign Network 99
- Parameters 99
- Duplicate IP Address 102
- Detection 102
- Duplicate detection scenarios 103
- IP Address Swapping 104
- Interpret the Indicators 105
- Functional Details 106
- 1794-IB16D Diagnostic 106
- For 3-wire sensors: 107
- 1794-OB16D Diagnostic 109
- (20 KΩ + 110
- Appendix 111
- Find Your Module 111
- *Fuse on 1794-TBNF only 113
- * Fuse on 1794-TBNF only 114
- Flexbus Interface 117
- 1794-OW8 Relay Output Module 126
- 126 Index 128
- How Are We Doing? 129
- BUSINESS REPLY MAIL 130
- Rockwell Automation 132
Relacionado con productos y manuales para Equipo Rockwell-automation 1794-OB16D FLEX I/O Diagnostic Modules User Manual
Equipo Rockwell-automation 2711P-RAT12E2 Adapter Kit for PanelView 1200/1200E Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 45C67 Dual Output Module/AutoMate/AutoMax/DCS Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2711-NP2 Mounting Clips for PanelView 600, 900, 10 Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 2706-LV2S_LV4S DL40 PLUS SLAVE USER MANUAL Manual de usuario
(60 paginas)
(60 paginas)
Equipo Rockwell-automation 61C516 AutoMax/AutoMate 24VAC/DC Input Module Manual de usuario
(38 paginas)
(38 paginas)
Equipo Rockwell-automation 2706-F11J_F11JC_F21J_F21JC DL50 INSTALLATION MANUA Manual de usuario
(135 paginas)
(135 paginas)
Equipo Rockwell-automation 2711P-RTFC Mounting Levers for PanelView Plus 400 Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 9323-PA2E APS SLC 500 Import/Export Utility User M Manual de usuario
(110 paginas)
(110 paginas)
Equipo Rockwell-automation 2100 Connecting a CENTERLINE Motor Control Center Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 61C350 2-In/2-Out 0-10 Volt Analog Rail Module Manual de usuario
(48 paginas)
(48 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales