Rockwell-automation 20B PowerFlex 70, PowerFlex 700 Reference Manual Manual de usuario Pagina 72
- Pagina / 214
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Digital Inputs
72 Rockwell Automation Publication PFLEX-RM001H-EN-P - June 2013
PowerFlex 70 Digital Input Selection
The available functions are defined in Tab le 9
.
Table 9 Digital Input Function List
INPUTS & OUTPUTS (File J)
Digital Inputs
361
362
363
364
365
366
[Digital In1 Sel]
[Digital In2 Sel]
[Digital In3 Sel]
[Digital In4 Sel]
[Digital In5 Sel]
[Digital In6 Sel]
Selects the function for the digital inputs.
(1)
When [Digital Inx Sel] is set to option 2 “Clear
Faults” the Stop button cannot be used to clear a
fault condition.
(2)
Ty p ic al 3-Wire Inputs.
Requires that only 3-wire functions are chosen.
Including 2-wire selections will cause a type 2
alarm.
(3)
Ty p ic al 2-Wire Inputs.
Requires that only 2-wire functions are chosen.
Including 3-wire selections will cause a type 2
alarm.
(4)
Speed Select Inputs.
To access Preset Speed 1, set [Speed Ref A Sel]
or [Speed Ref B Sel] to “Preset Speed 1”.
Ty p e 2 Al arms
Some digital input programming may cause
conflicts that will result in a Ty pe 2 alarm. Example:
[Digital In1 Sel] set to 5 “Start” in 3-wire control and
[Digital In2 Sel] set to 7 “Run” in 2-wire.
Refer to Alarm Descriptions in the User Manual for
information on resolving this type of conflict.
(5)
Auto/Manual - Refer to User Manual for details.
(6)
Opening an “Enable” input will cause the motor to
coast-to-stop, ignoring any programmed Stop
modes.
(7)
A “Dig In ConflictB” alarm will occur if a “Start”
input is programmed without a “Stop” input.
Default:
Default:
Default:
Default:
Default:
Default:
Options:
4
5
18
15
16
17
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
“Stop – CF”
(CF = Clear Fault)
“Start”
“Auto/ Manual”
“Speed Sel 1”
“Speed Sel 2”
“Speed Sel 3”
“Not Used”
“Enable”
(6)
“Clear Faults”
(1)
“Aux Fault”
“Stop – CF”
(2)
“Start”
(2)(7)
“Fwd/ Reverse”
(2)
“Run”
(3)
“Run Forward”
(3)
“Run Reverse”
(3)
“Jog”
(2)
“Jog Forward”
“Jog Reverse”
“Stop Mode B”
“Bus Reg Md B”
“Speed Sel 1”
(4)
“Speed Sel 2”
(4)
“Speed Sel 3”
(4)
“Auto/ Manual”
(5)
“Local”
“Acc2 & Dec2”
“Accel 2”
“Decel 2”
“MOP Inc”
“MOP Dec”
“Excl Link”
“PI Enable”
“PI Hold”
“PI Reset”
100
156
162
096
140
194
380
384
388
124
Input Function Name Purpose
Stop - CF Stop drive
Clear Faults (open to closed transition)
Run Forward Run in forward direction (2-wire start mode)
Run Reverse Run in reverse direction (2-wire start mode)
Run Run in current direction (2-wire start mode)
Start Start drive (3-wire start mode)
Forward/Reverse Set drive direction (3-wire mode only)
Jog Jog drive
Jog Forward Jog in forward direction
Jog Reverse Jog in reverse direction
Speed Select 3
Speed Select 2
Speed Select 1
Select which Speed reference the drive uses.
Auto/Manual Allows terminal block to assume complete control of Speed Reference.
3 21Auto Reference Source
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Reference A
Reference B
Preset Speed 2
Preset Speed 3
Preset Speed 4
Preset Speed 5
Preset Speed 6
Preset Speed 7
- Reference Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Chapter 1 9
- General Precautions 10
- Detailed Drive Operation 11
- Alarm Status Indication 15
- INPUTS & OUTPUTS 17
- Analog Input Configuration 19
- Analog Inputs 20
- Analog Scaling 22
- Output Hertz 23
- Input mA 24
- Torque Ref % 26
- Input Volts 26
- Value Display 28
- Cable Selection 28
- Explanation 31
- Output Current 32
- Output Voltage 32
- Table 1 Software Filters 34
- Auto/Manual 37
- Autotune 40
- PowerFlex 700VC 44
- Speed Control - Reference 46
- (2.0 ms) 46
- Speed Control - Regulator 48
- (1.0 ms) 48
- Torque Control 49
- (0.25ms) 49
- Process Trim 50
- MOP Control 51
- Block Diagrams 52
- Inputs & Outputs - Analog 53
- Control Logic 54
- (2.0ms) 54
- Inverter Overload IT 55
- Bus Regulation [Bus Reg Gain] 56
- Single Seq 500 S/s 56
- Operation 57
- Motor Speed 57
- Proportional Channel 58
- Integral Channel 58
- Bus Regulation 59
- Table 3 60
- Table 4 61
- Carrier (PWM) Frequency 62
- EMC Instructions 63
- Table 8 Recommended Filters 65
- Current Limit 66
- Datalinks 67
- Decel Time [Decel Time 1, 2] 69
- Wiring Examples 70
- Digital Inputs 75
- Digital Input Conflict Alarms 83
- Output Time Delay 90
- Client/Server 92
- Peer-to-Peer operation 93
- Overall RMS Protection 95
- Drive Overload 96
- Thermal Manager Protection 97
- PWM Frequency 97
- DTO Fault 98
- Temperature Display 98
- Low Speed Operation 98
- Drive Ratings (kW, Amps 99
- Economizer 99
- (Auto-Economizer) 99
- Fan See Fan Curve above 100
- When a Fault Occurs 101
- Fault Queue 101
- Fault Time [Fault 1-8 Time] 102
- Resetting or Clearing a Fault 102
- Flux Braking 103
- Flux Up [Flux Up Mode] 104
- Flying Start 105
- Configuration 106
- Application Example 106
- Input Devices Contactors 108
- Input Power Conditioning 110
- Table 13 Linkable Parameters 112
- COMMUNICATION 113
- 00000100 114
- Adapter # X6543210 114
- Motor Control 115
- Trip Time (Seconds) 117
- Motor Overload 118
- 20 Minutes 119
- 1 Minute 1 Minute 119
- Motor Start/Stop 120
- Precautions 120
- Jm Jload 121
- Figure 26 Resonance 122
- Figure 27 10 Hz Notch 122
- Drive Output Contactor 123
- Cable Termination 123
- Output Frequency 124
- COMMUNICATIONS 126
- Table 14 PF70 Bus Levels 128
- Table 15 PF700 Bus Levels 129
- Power Loss 131
- Decel Input (PF700 only) 134
- Process PI Loop [PI Config] 135
- 10 Volts 136
- Process PI Loop 137
- Normalized Feedback 141
- Normalized SQRT(Feedback) 141
- PI Reference and Feedback 143
- PI Reference Scaling 143
- PI Setpoint 144
- PI Output 144
- PI Gains 144
- Positive and Negative Limits 145
- Output Scaling 145
- Vector v3 147
- Factory Default Bit Values 148
- Reflected Wave [Compensation] 149
- 50 10152025 149
- 30 35404550 149
- Reflected Wave 150
- Example Configuration #1 154
- Example Configuration #2 155
- Analog Out1 Value (Volts) 155
- Scale1 In Value = 155
- Encoder Speed (RPM) 155
- Example Configuration #3 156
- PI Reference 156
- Analog In2 Value (Volts) 156
- DYNAMIC CONTROL 157
- Figure 31 Skip Frequency 158
- . This function affects 159
- Sleep Mode Operation 160
- Interactive functions 161
- Sleep/Wake Levels 161
- Sleep/Wake Sources 161
- Wake Level 162
- Sleep Level 162
- Analog Signal 162
- Speed Reference Operation 167
- Frequency Reference 169
- Figure 36 Trim 170
- Speed Regulator 171
- Figure 37 172
- Speed Regulation Mode 173
- Torque Regulation Mode 173
- Figure 38 174
- Figure 39 175
- Permissive Conditions 176
- Start-Up Start-Up Routines 177
- Basic Start Up (Top Level) 178
- Start-Up 179
- Basic Start Up (Motor Tests) 181
- Basic Start Up (Speed Limits) 182
- Stop Modes [Stop Mode A, B] 197
- Stop Modes 198
- Test Points 200
- Torque Performance 201
- Sensorless Vector 202
- V/Hz Control 202
- Flux Vector Control 203
- Figure 59 Flux Vector 204
- Figure 60 204
- Unbalanced or 205
- Ungrounded Distribution 205
- Figure 61 User Sets 206
- Voltage Class 207
- Watts Loss 208
- Rockwell Automation Support 214
- Documentation Feedback 214
Relacionado con productos y manuales para Equipo Rockwell-automation 20B PowerFlex 70, PowerFlex 700 Reference Manual
Equipo Rockwell-automation 20D PowerFlex 700H/700S AC Drives Frames 13 and 14 Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation PDS- Sprecher+Schuh PDS Soft Starter (6-Lead, Star Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 20D PowerFlex 700H/S Frame 11 Replacement Power St Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation MHB44IND Pulse Input and Analogue Output Module Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation Liquiflo AC Drive Panel Mount Kit, M/N 41L4060, Mo Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation T8850 Trusted Analogue or Digital Output FTA Manual de usuario
(14 paginas)
(14 paginas)
Equipo Rockwell-automation Sipha Coded Magnetic Interlock Switch Control Unit Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation MSR04XI Serial Communications Module RS232 Manual de usuario
(13 paginas)
(13 paginas)
(4 paginas)
Equipo Rockwell-automation GV3000/SE AC Gen. Purpose and Vector Drive Softwar Manual de usuario
(232 paginas)
(232 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales