Rockwell-automation 1761 MicroLogix 1000 Programmable Controllers Manual de usuario Pagina 351
- Pagina / 422
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Application Example Programs
E–1
E
Application Example Programs
This
appendix is designed to illustrate various instructions described previously in
this manual. Application example programs include:
• paper drilling machine using most of the software instructions
• time driven sequencer using T
ON and SQO instructions
•
event driven sequencer using SQC and SQO instructions
• bottle line example using the HSC instruction (Up/down counter)
• pick and place machine example using the HSC instruction (Quadrature
Encoder with reset and hold)
•
RPM calculation using HSC, R
TO, timer, and math instructions
• on/off circuit using basic, program flow
, and application specific instructions
• spray booth using bit shift and FIFO instructions
•
adjustable time delay example using timer instructions
Because of the variety of uses for this information, the user of and those responsible
for applying this information must satisfy themselves as to the acceptability of each
application and use of the program. In no event will Allen-Bradley Company be
responsible or liable for indirect or consequential damages resulting from the use of
application of this information.
The illustrations, charts, and examples shown in this appendix are intended solely to
illustrate the principles of the controller and some of the methods used to apply
them. Particularly because of the many requirements associated with any particular
installation, Allen-Bradley Company cannot assume responsibility or liability for
actual use based upon the illustrative uses and applications.
Reference
- MicroLogix 1000 1
- Programmable 1
- Controllers 1
- Allen-Bradley 1
- Important User Information 2
- Table of Contents 3
- toc–iii 5
- Summary of Changes 9
- • the purpose of this manual 11
- • Allen-Bradley support 11
- Who Should Use this Manual 12
- Purpose of this Manual 12
- Contents of this Manual 13
- Glossary 14
- Related Documentation 15
- Allen-Bradley Support 16
- Installing Your Controller 17
- EMC Directive 18
- • EN 50081-2 18
- • EN 50082-2 18
- Hardware 19
- Hardware Overview 19
- Master Control Relay 20
- Schematic (Using IEC Symbols) 22
- Using Surge Suppressors 24
- Recommended Surge Suppressors 26
- Safety Considerations 27
- Power Distribution 28
- Power Considerations 29
- Preventing Excessive Heat 31
- Controller Spacing 32
- Mounting the Controller 32
- Using Mounting Screws 34
- Wiring Your Controller 35
- Grounding Guidelines 36
- Sinking and Sourcing Circuits 37
- Wiring Recommendations 38
- 1761-L16AWA Wiring Diagram 41
- 1761-L32AWA Wiring Diagram 42
- HardwareHardware 43
- 1761-L32AAA Wiring Diagram 49
- 0V dc 5V dc 51
- 26.4V dc @ 55° C (131° F) 51
- 0V dc 26.4V dc20.4V dc 51
- 1761-L20AWA-5A Wiring Diagram 52
- 85–264 VAC 53
- 0V dc 5V dc 14V dc 54
- 0V dc 125V dc5V dc 54
- 0V ac 264V ac5V ac 54
- Grounding 55
- O/4 O/5 O/6 56
- I/10 I/11 56
- Analog Voltage Input Range 57
- Analog Current Input Range 57
- Analog Voltage Output Range 57
- Analog Current Output Range 57
- Applications 58
- Connecting the System 59
- Connecting the DF1 Protocol 60
- Constructing 62
- DH-485 Communication Cable 64
- Connecting the AIC+ 67
- DH-485 Network Connection 68
- DF1 Isolated Modem Connection 69
- 1761-CBL-PM02 71
- 1761-CBL-AP00 71
- supplied cable 71
- connector Port 3 72
- DB-9 RS-232 Port 1 72
- Powering the AIC+ 73
- Establishing Communication 75
- DeviceNet Communications 76
- Programming Overview 77
- Principles of Machine Control 78
- Maximum) 80
- (8 Maximum) 80
- Accessed 82
- Power Down 84
- Power Up 84
- Addressing Data Files 86
- Specifying Indexed Addresses 88
- Developing 91
- Development 92
- Program Development 92
- Checklist 92
- Using Analog 93
- I/O Image 94
- I/O Configuration 95
- Input Filter and Update Times 95
- Update Examples 96
- Input Channel Filtering 96
- Converting Analog Data 97
- Converting Analog Output Data 98
- Using Basic Instructions 99
- About the Basic Instructions 100
- Bit Instructions Overview 101
- Programming 101
- Examine if Closed (XIC) 102
- Examine if Open (XIO) 102
- Output Energize (OTE) 103
- Using OTL 104
- Using OTU 104
- One-Shot Rising (OSR) 105
- Timer Instructions Overview 106
- Timer On-Delay (TON) 109
- Timer Off-Delay (TOF) 110
- Retentive 112
- Counter Instructions Overview 113
- Entering Parameters 114
- Addressing Structure 114
- Count Up (CTU) 116
- Count Down (CTD) 117
- Reset (RES) 118
- Application Example 119
- Using Comparison Instructions 123
- Indexed Word Addresses 124
- Equal (EQU) 125
- Not Equal (NEQ) 125
- Less Than (LES) 125
- Less Than or Equal (LEQ) 126
- Greater Than (GRT) 126
- Greater Than or Equal (GEQ) 126
- Using Math Instructions 133
- About the Math Instructions 134
- Math Instructions Overview 134
- Add (ADD) 136
- Subtract (SUB) 137
- Multiply (MUL) 140
- Divide (DIV) 141
- Double Divide (DDV) 142
- Clear (CLR) 143
- Square Root (SQR) 143
- Scale Data (SCL) 144
- Convert to BCD (TOD) 151
- Convert from BCD (FRD) 153
- Decode 4 to 1 of 16 (DCD) 156
- Encode 1 of 16 to 4 (ENC) 157
- Using FLL 160
- • Length is the number of wor 160
- Overflow Trap Bit, S:5/0 162
- Move (MOV) 163
- Masked Move (MVM) 164
- And (AND) 166
- Exclusive Or (XOR) 168
- Not (NOT) 169
- Negate (NEG) 170
- Operation 174
- Using Program Flow Control 179
- Instructions 179
- Jump (JMP) and Label (LBL) 180
- Return (RET) 182
- Using SBR 184
- Using RET 184
- Master Control Reset (MCR) 185
- Temporary End (TND) 186
- Suspend (SUS) 186
- Machine Application Example 188
- Using Application Specific 189
- • Bit Address 192
- Bit Shift Left (BSL) 193
- Bit Shift Right (BSR) 194
- Using SQO 198
- Sequencer Load (SQL) 201
- Selectable 203
- Between instruction updates 204
- Between communication packets 204
- At start and end 204
- Interrupt Subroutine (INT) 208
- Using High-Speed Counter 215
- High-Speed Counter (HSC) 220
- High-Speed Counter Load (HSL) 232
- (µsec) when: 236
- True False 236
- 56.00 6.00 236
- Execution Times 236
- Using HSD 238
- Example 1 240
- Example 3 242
- Using the Message Instruction 249
- Types of Communication 250
- Message Instruction (MSG) 251
- • Control Block Address 252
- MSG Instruction Error Codes 258
- SLC500/ML1000 263
- TIMER ON DELAY 264
- Timer T4:0 264
- Time Base 0.01 264
- Preset 400 264
- Example 5 266
- Troubleshooting Your System 269
- When Operating Normally 270
- Troubleshooting 271
- Identifying Controller Faults 274
- • controller LED status 278
- Hardware Reference 279
- Controller Specifications 280
- Reference 281
- General Output Specifications 283
- Analog Input Specifications 284
- Analog Output Specifications 284
- -L32BBB controllers) 286
- -L32AAA controllers) 286
- Controller Dimensions 287
- Replacement Parts 288
- Programming Reference 289
- NA = Not Applicable 302
- ReferenceReference 307
- User Interrupt Latency 312
- Execution Time Worksheet 314
- Available 316
- Available Addressing Modes 317
- ➀ Indexed 322
- , C, or R addresses 322
- Protocols 329
- DF1 Full-Duplex Protocol 331
- Modem Modem Modem 335
- Ownership Timeout 336
- DH-485 Communication Protocol 339
- DH-485 Token Rotation 340
- • baud rate 346
- Typical 3-Node Network 348
- Network 348
- (not expandable) 348
- Application Example Programs 351
- Drill Mechanism Operation 354
- Conveyor Operation 354
- Drill Calculation and Warning 354
- Bottle Line Example 371
- Bottle Line Ladder Program 372
- Conveyor 374
- On/Off Circuit Ladder Program 384
- Spray Booth Ladder Program 388
- Adjustable 391
- Calibration 393
- Calibration Procedure 395
- Worldwide 422
Relacionado con productos y manuales para Equipo Rockwell-automation 1761 MicroLogix 1000 Programmable Controllers
Equipo Rockwell-automation 1747-ACNR15 ControlNet Adapter Module Installation Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1794-ASB/E Remote I/O Adapter Module User Manual Manual de usuario
(72 paginas)
(72 paginas)
Equipo Rockwell-automation ControlFLASH Firmware Upgrade Kit User Manual Manual de usuario
(50 paginas)
(50 paginas)
Equipo Rockwell-automation 1790D-XXXX DeviceNet Analog Base D-Shell CompactBl Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1734-8CFGDLX POINT I/O Module with 8 Configurable Manual de usuario
(28 paginas)
(28 paginas)
Equipo Rockwell-automation 1756-L6x_L7x ControlLogix System User Manual Manual de usuario
(212 paginas)
(212 paginas)
Equipo Rockwell-automation 1794-OF8IH FLEX I/0 8 Isolated Output Analog Modul Manual de usuario
(28 paginas)
(28 paginas)
Equipo Rockwell-automation 1746-Ax SLC 500 Modular Chassis/ Instructions Manual de usuario
(80 paginas)
(80 paginas)
Equipo Rockwell-automation 1785-Vx0B, D17856.5.9 PLC-5 VME VMEbus Programmabl Manual de usuario
(275 paginas)
(275 paginas)
Equipo Rockwell-automation Logix5000 Controllers Sequential Function Charts P Manual de usuario
(88 paginas)
(88 paginas)
Equipo Rockwell-automation 1762-RTC MicroLogix 1200 Real-Time Clock and Memor Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1790-TXXXX CompactBlock LDX I/O Profibus Analog, R Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation 1756-EN2TXT ControlLogix-XT EtherNet/IP Bridge Mod Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1784-PKTX_PKTXD Communication Card User Manual Manual de usuario
(38 paginas)
(38 paginas)
Equipo Rockwell-automation 1734-IT2I, Series C Point I/O RTD and Isolated The Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1771-PM , D17716.5.18 U MNL 1771-PM CLUTCH/BRAKE M Manual de usuario
(143 paginas)
(143 paginas)
Equipo Rockwell-automation 1753-CFBBASIC Certified Function Blocks for RSLogi Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales