Rockwell-automation 1797-OE8H FLEX Ex HART Analog Modules User Manual Manual de usuario Pagina 54
- Pagina / 196
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Publication 1797-6.5.3 - March 2006
3-2 How to Install Your FLEX Ex Analog Modules
Compliance to European
Union Directives
If these products have the CE mark they are approved for installation within
the European Union and EEA regions. They have been designed and tested to
meet the following directives.
EMC Directive
These products are tested to meet the Council Directive 89/336/EC
Electromagnetic Compatibility (EMC) as amended by 92/31/EC and
93/68/EEC, by applying the following standards:
• EN61000-6-4:2001, Electromagnetic Compatibility (EMC) - Part 6-4:
Generic Standard for Industrial Environments (Class A)
• EN61000-6-2:2001, Electromagnetic Compatibility (EMC) - Part 6-2:
Generic Standards - Immunity for Industrial Environments
• EN61326-1997 + A1-A2, Electrical Equipment For Measurement,
Control, and Laboratory Use - Industrial EMC Requirements
ATEX Directive
These products are tested in conjunction with associated I/O modules to meet
the Council Directive 94/9/EC (ATEX) Equipment and Protective Systems
Intended for Use in Potentially Explosive Atmospheres by applying the
following standards:
• EN50014:1997 + A1-A2, Electrical Apparatus for Potentially Explosive
Atmospheres
• EN50020:1994, Electrical Apparatus for Potentially Explosive
Atmospheres - Intrinsic Safety “i”
• EN50284:1999, Special Requirements for Construction, Test and
Marking of Electrical Apparatus of Equipment Group II, Category 1G
• EN50281-1-1:1998 + A1, Electrical Apparatus for Use in the Presence
of Combustible Dust - Part 1-1: Protection by Enclosure
- FLEX Ex HART 1
- Analog Modules 1
- Important User Information 2
- Summary of Changes 3
- What’s Changed 3
- Summary of Changes 2 4
- Table of Contents 5
- Chapter 3 6
- How to Install Your FLEX Ex 6
- Table of Contents 3 7
- Table of Contents 4 8
- Table of Contents 5 9
- Table of Contents 6 10
- Table of Contents 7 11
- Table of Contents 8 12
- For Additional Information 14
- What This Chapter Contains 15
- What the FLEX Ex Analog 15
- I/O Modules Do 15
- How FLEX Ex Analog 16
- Modules Communicate 16
- Controllers 16
- Physical Features of Your 17
- Analog I/O Module 17
- Using Alarms on the 17
- 1797-IE8H Module 17
- Data Format Alarm Example 18
- Overrange Alarm 18
- Underrange Alarm 18
- Remote Fault Alarm 19
- Local Fault Alarm 20
- How to Use the 21
- HART Capabilities 21
- HART Implementation 21
- Overview 21
- HART Commands 22
- HART Target Tags 23
- HART Command Tags 24
- HART Initialize Tags 25
- HART Initialize Channel Tags 26
- Selecting the Correct Path 29
- Module Features 31
- Selecting a 1797-IE8H FLEX 32
- Ex Analog Input Module’s 32
- Operating Features 32
- High Low Error Level 33
- Input Filter Cutoff 33
- Data Format 34
- Data Formats and Error Ranges 36
- Selecting a 1797-OE8H FLEX 37
- Ex Analog Output Module’s 37
- Analog Digital State 38
- Analog Fault State Value 38
- Diagnostic Data error 40
- 11=data out of range 40
- Understanding Image Table 42
- Mapping and Bit/Word 42
- Descriptions 42
- 1797-IE8H and -OE8H 49
- Extended Configuration 49
- Data Table 49
- HART Status LEDs 50
- HART Status Inhibit 50
- 50/60 Hz Filter 50
- Before You Install Your 53
- Analog Module 53
- Compliance to European 54
- Union Directives 54
- Installation in Zone 1 55
- Installation in Zone 22 55
- Electrostatic Charge 55
- Removal and Insertion 56
- Under Power 56
- Install the Module 56
- Mount on a DIN Rail 57
- Panel/Wall Mount 59
- Label under here 61
- Wire the Terminal Base 62
- Connecting Wiring to the 63
- FLEX Ex I/O Analog 63
- ATTENTION 64
- Ground the Module 66
- ControlNet Network 69
- Using Programming 70
- Software in Your FLEX Ex 70
- Application 70
- About the ControlNet Ex 70
- Communication Over the 71
- FLEX Ex Backplane 71
- Unscheduled Data Transfer 72
- Module I/O Mapping 72
- I/O Structure 73
- Fault State Data 75
- Device Actions 75
- Calibrate Your Module 77
- When and How to Calibrate 78
- Your FLEX Ex Analog I/O 78
- Tools and Equipment 78
- 1797-IE8H Calibration 79
- Features 79
- Command Structure 80
- 2 Calibrate gain at 25 °C 81
- °C Channel-Mask 82
- 25 °C according to 83
- . During the 87
- 1797-OE8H Calibration 88
- Calibration) 96
- Evaluate the Application 99
- Define the Area 100
- Classification 100
- Select Protection 101
- Method(s) 101
- Match Field Devices and 101
- I/O Modules 101
- Optimize Power 105
- Distribution 105
- Assigning Power Supplies 106
- Safe Area 107
- Hazardous Area 107
- Chapter Summary 108
- Troubleshoot the FLEX Ex 109
- Analog I/O Modules 109
- 8 CHANNEL ANALOG OUTPUT 110
- Specifications 113
- Class I Division 1 Hazardous 114
- Specifications A-3 115
- Wiring Methods 116
- IMPORTANT 117
- A-6 Specifications 118
- Specifications A-9 121
- 1797-OE8H Output Module 122
- Specifications A-11 123
- A-12 Specifications 124
- FLEX Ex HART Module Commands 125
- Universal Commands 126
- Common Practice 127
- Commands 127
- Device-specific Commands 127
- Command 129 128
- Command 130 130
- Command 131 131
- Command 132 132
- Command 133 132
- Command 134 133
- Command 135 134
- Command 136 135
- Command 137 136
- Command 138 137
- Command 139 138
- Command 140 139
- Command 141 140
- Command 143 141
- Command 144 141
- Command 145 142
- Command 146 143
- Command 147 144
- Command 148 144
- Command 149 145
- Command 152 145
- Command 154 146
- Command 158 147
- Command 159 148
- Command 164 148
- Appendix 149
- What This Appendix 149
- Contains 149
- Message Structure 149
- Transaction Procedure 150
- Burst Mode (not supported) 150
- Preamble 151
- Start Character 151
- HART Address 151
- HART Command 152
- Byte Count 152
- Check Byte 152
- Response Code 153
- Background Information 165
- Configuration 166
- Analog Fault State 168
- Fault Mode 168
- Local Fault Mode 168
- Latch Retry Mode 169
- Analog/Digital Mode 169
- Digital Fault State 170
- Analog Fault State Values 170
- Digital Output Data 171
- Global Reset Bit 171
- Analog Output Data 171
- Diagnostic Status Data 172
- HART Rebuild Bit 172
- Fault Alarm 172
- HART Failure 173
- HART Readback 173
- HART Communication 173
- HART Transmitter 174
- Filter Cutoff 178
- Up/Down Bit 179
- High and Low Error Level 179
- Square Root Threshold 181
- Analog Input Data 181
- Local Fault 182
- Remote Fault 182
- Diagnostic Status 183
- Communication 185
- Differences Between 187
- Attributes and Assembly 187
- HART Frame Enhancements 190
- 2 192
- How Are We Doing? 193
- BUSINESS REPLY MAIL 194
- Rockwell Automation 196
Relacionado con productos y manuales para Equipo Rockwell-automation 1797-OE8H FLEX Ex HART Analog Modules User Manual
Equipo Rockwell-automation 7000L PowerFlex 7000 Medium Voltage AC Drive C Fra Manual de usuario
(350 paginas)
(350 paginas)
Equipo Rockwell-automation 1794-OE8H FLEX I/O HART Analog Modules User Manual Manual de usuario
(146 paginas)
(146 paginas)
Equipo Rockwell-automation 2711p-RAK15, -RAT15 Adapter Kit for PanelView 1400 Manual de usuario
(28 paginas)
(28 paginas)
Equipo Rockwell-automation 47C626 AutoMax Programming Executive V4.2 Manual de usuario
(278 paginas)
(278 paginas)
Equipo Rockwell-automation DeviceNet Communications for PanelView Plus and Pa Manual de usuario
(76 paginas)
(76 paginas)
Equipo Rockwell-automation 7000A PowerFlex Medium Voltage AC Drive (A Frame) Manual de usuario
(208 paginas)
(208 paginas)
Equipo Rockwell-automation 2711E-NKSW1 Replacement Keyswitch Assembly Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 7703E Medium Voltage SMC OEM Components - 10-15 kV Manual de usuario
(58 paginas)
(58 paginas)
Equipo Rockwell-automation 2099-BMxxx Kinetix 7000 High Power Servo Drive Lif Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 60-2428 Special Mounting Assembly for Series 5000 Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 6180 RAC6180 Industrial Computers Installation Ins Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation 2711E-ND1 PanelBuilder 1400E Configurator Software Manual de usuario
(114 paginas)
(114 paginas)
Equipo Rockwell-automation 9904-PCIC ControlNet 9904-PCIC Communications Card Manual de usuario
(18 paginas)
(18 paginas)
Prodotti e manuali riguardandi Illuminazione Feiss F1919-6+1
Illuminazione Feiss F2517 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2304 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F1798 Manuale Utente
(3 pagine)
(3 pagine)
Illuminazione Feiss F2303 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F1883 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2228 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2529 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2423 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2530 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2535 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2405 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2519 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2546 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2478 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2726 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2724 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2722 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2713 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss F2712 Manuale Utente
(1 pagine)
(1 pagine)
Illuminazione Feiss FL6318 Manuale Utente
(4 pagine)
(4 pagine)
© 2020, manymanuals.es. Todos los derechos reservados | 0.093 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales