Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module Manual de usuario Pagina 20
- Pagina / 144
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
20 Rockwell Automation Publication 750COM-UM002B-EN-P - October 2012
Chapter 2 Installing the Option Module
Connecting the Option
Module to the Network
1. Remove power from the drive.
2. Remove the drive cover and lift up the drive HIM bezel to its open
position to access the drive control pod.
3. Use static control precautions.
4. Connect one end of the DeviceNet cable to the network. We recommend
DeviceNet Thin cable with an outside diameter of 6.9 mm (0.27 in.).
5. Route the other end of the DeviceNet cable through the bottom of the
drive, and connect the 5-pin linear plug (provided with the option
module) to the DeviceNet cable (Figure 3
). If a replacement plug is
needed, the replacement plug part number is 1799-DNETSCON.
Figure 3 - Connecting the 5-Pin Linear Plug to the DeviceNet Cable
6. Insert the 5-pin linear plug into the mating option module receptacle, and
secure it with the two screws. Verify that the colors of the wires on the plug
match the color codes on the receptacle.
ATTENTION: Risk of injury or death exists. The PowerFlex drive may contain high
voltages that can cause injury or death. Remove power from the drive, and then
verify power has been discharged before connecting the option module to the
network.
IMPORTANT
Maximum cable length depends on data rate. For details, see Data Rate
on page 134.
Terminal Color Signal Function
5 Red V+ Power Supply
4 White CAN_H Signal High
3BareSHIELDShield
2 Blue CAN_L Signal Low
1BlackV– Common
5
4
3
2
1
Red
White
Bare
Blue
Black
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Conventions Used in This 9
- Rockwell Automation 9
- Additional Resources 10
- Getting Started 11
- Features 12
- Understanding Parameter 13
- Compatible Products 13
- Required Equipment 13
- User-Supplied Equipment 14
- Safety Precautions 15
- Quick Start 16
- Installing the Option Module 17
- Setting the Node Address 18
- Switches 18
- Setting the Data Rate Switch 19
- Connecting the Option 19
- Module to the Drive 19
- Module to the Network 20
- Start-Up Status Indications 21
- Commissioning the Option 24
- Configuring the Option Module 25
- Edit Net Addr Cfg 26
- Autobaud 3 27
- 0<<16 28
- Edit DLs To Net Cfg 29
- Value Description 30
- 1 Use this logic bit 30
- Changing the Fault Action 31
- Resetting the Option Module 32
- 0<<2 32
- Host Drive 33
- 240V 4.2A 33
- Rev 3.002 Ser. A 33
- Viewing the Option Module 34
- Status Using Parameters 34
- Updating the Option Module 35
- Firmware 35
- Configuring the I/O 37
- ControlLogix Controller 38
- Configuring the I/O Chapter 4 39
- I/O to the Scanner 41
- Chapter 4 Configuring the I/O 42
- Using the I/O 53
- Understanding the 54
- ControlLogix Controller I/O 54
- Using Logic Command/Status 54
- Using Reference/Feedback 55
- Using Datalinks 56
- Example Ladder Logic 57
- Program Information 57
- Program 59
- Status/Feedback 61
- Logic Command/Reference 61
- Generic Profile 62
- Using the I/O Chapter 5 63
- Chapter 5 Using the I/O 64
- Using Explicit Messaging 65
- About Explicit Messaging 66
- Examples 68
- Single Parameter 70
- Multiple Parameters 72
- Request (Source Data) array 79
- Troubleshooting 81
- PORT Status Indicator 82
- MOD Status Indicator 82
- NET A Status Indicator 83
- Viewing Option Module 84
- Diagnostic Items 84
- Viewing and Clearing Events 86
- Specifications 89
- Environmental 90
- Regulatory Compliance 90
- Option Module Parameters 91
- About Parameter Numbers 92
- How Parameters Are 92
- Organized 92
- Device Parameters 92
- Host Parameters 94
- DeviceNet Objects 99
- Identity Object 100
- Connection Object 101
- Register Object 102
- PCCC Object 103
- N-Files 105
- DPI Device Object 106
- Class Attributes 107
- Instance Attributes 108
- DPI Parameter Object 109
- Formula number 111
- Extended DPI descriptor 111
- Descriptor Attributes 112
- Formulas for Converting 114
- Common Services 114
- Object Specific Services 114
- DPI Fault Object 115
- DPI Alarm Object 117
- DPI Diagnostic Object 119
- DPI Time Object 121
- Host DPI Parameter Object 123
- 750-Series Drives 129
- History of Changes 131
- Appendix E History of Changes 132
- Glossary 133
- Rockwell Automation Support 144
- Documentation Feedback 144
Relacionado con productos y manuales para Equipo Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module
Equipo Rockwell-automation 445L GuardShield Safe 4 and Safe 4 PAC Safety Ligh Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 160 Supplement-160-NX3 Chassis Mount Series C Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 140U Q, M frame CB Electronic RMS Trip Unit instal Manual de usuario
(14 paginas)
(14 paginas)
Equipo Rockwell-automation 440N SensaGuard Magnetically Coded NonContact Swit Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 193-ERR E1 PLUS Remote Reset Accessory Module Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 193- E3 User Manual Instruction Sheet for High Fau Manual de usuario
(1 paginas)
(1 paginas)
Equipo Rockwell-automation 193-EPB_EPD_EPE Overload Relay Panel or DIN Rail A Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 700-RTC_RTCR Type RTC RTCR Solid-State Relays Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 20-750-CNETC PowerFlex Coaxial ControlNet Option M Manual de usuario
(150 paginas)
(150 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales