Rockwell-automation 20-750-PBUS Profibus DPV1 Option Module Manual de usuario Pagina 34
- Pagina / 96
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
34 Rockwell Automation Publication 750COM-UM004B-EN-P - September 2012
Chapter 3 Configuring the Option Module
Setting the Fault Configuration Parameters
When setting Host Parameters 33 - [Comm Flt Action] and 34 - [Idle Flt
Action] to ‘Send Flt Cfg’, the values in the following parameters are sent to the
drive after a communication fault and/or idle fault occurs. You must set these
parameters to values required by your application.
Changes to these parameters take effect immediately. A reset is not required.
Resetting the Option
Module
Changes to switch settings and some option module parameters require you to
reset the option module before the new settings take effect. You can reset the
option module by power cycling the drive or by using Device Parameter 07 -
[Reset Module].
Set Device Parameter 07 - [Reset Module] to ‘1’ (Reset Module).
When you enter ‘1’ (Reset Module), the option module will be immediately reset.
An alternate method to reset the module is by power cycling the drive. When you
enter ‘2’ (Set Defaults), the option module will set ALL of its Device and Host
parameters to their factory default values. (This is the same as pressing the ALL
soft key when using the MEMORY folder method described in Restoring Option
Module Parameters to Factory Defaults on page 35). After performing a Set
Defaults, you must enter ‘1’ (Reset Module) or power cycle the drive so that the
new values take effect. Thereafter, this parameter will be restored to a value of ‘0’
(Ready).
Option Module Host Parameter Description
Parameter 37 - [Flt Cfg Logic] A 32-bit value sent to the drive for Logic Command.
Parameter 38 - [Flt Cfg Ref] A 32-bit REAL (floating point) value sent to the drive for
Reference.
Parameter 39 - [Flt Cfg DL 01]
through
Parameter 54 - [Flt Cfg DL 16]
A 32-bit integer value sent to the drive for a Datalink. If the
destination of the Datalink is a REAL (floating point)
parameter, you must convert the desired value to the binary
representation of the REAL value. (An internet search of ‘hex
to float’ provides a link to a tool to do this conversion.)
ATTENTION: Risk of injury or equipment damage exists. If the option
module is transmitting control I/O to the drive, the drive may fault when
you reset the option module. Determine how your drive will respond before
resetting the option module.
Value Description
0 Ready (Default)
1 Reset Module
2 Set Defaults
ESC
ENTER
Stopped
0.00 Hz
AUTO
F
▲
▼
Edit Reset Module
Ready 0
0<<2
- PowerFlex 20-750-PBUS 1
- Profibus DPV1 Option Module 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Glossary 7
- Conventions Used in This 9
- Rockwell Automation 9
- Additional Resources 10
- Getting Started 11
- Features 12
- Understanding Parameter 13
- Compatible Products 13
- Required Equipment 13
- User-Supplied Equipment 14
- Safety Precautions 16
- Quick Start 17
- Installing the Option Module 19
- Setting the Endianness and 20
- Node Address Switches 20
- Connecting the Option 22
- Module to the Drive 22
- Module to the Network 23
- Network Termination 24
- Applying Power 25
- and page 67 26
- Configuring the Option Module 29
- 0 << 126 30
- Enable Datalinks To Read Data 32
- Setting a Fault Action 33
- 0<<2 34
- Restoring Option Module 35
- Parameters to Factory 35
- Defaults 35
- Viewing the Option Module 36
- Status Using Parameters 36
- Updating the Option 37
- Module Firmware 37
- Example Network 39
- Configuring the MVI56 40
- PDPMV1 Profibus DPV1 40
- Installing GSD Files 43
- Configuring the Option 45
- Module as a Slave 45
- Using the I/O 51
- Understanding the I/O 52
- Using Logic Command/ 52
- Using Reference/Feedback 53
- Using Datalinks 53
- I/O Communication 55
- Acyclic Messaging 57
- Acyclic Messaging for 60
- DPV1 Class 1 60
- Example Messaging 60
- Troubleshooting 65
- PORT Status Indicator 66
- MOD Status Indicator 67
- NET A Status Indicator 67
- Viewing Option Module 68
- Diagnostic Items 68
- Viewing and Clearing 70
- Specifications 73
- Environmental 74
- Regulatory Compliance 74
- Option Module Parameters 75
- About Parameter Numbers 76
- How Parameters Are 76
- Organized 76
- Device Parameters 76
- Host Parameters 78
- 750-Series Drives 83
- Logic Status Word 84
- History of Changes 85
- Rockwell Automation Support 96
- Documentation Feedback 96
Relacionado con productos y manuales para Equipo Rockwell-automation 20-750-PBUS Profibus DPV1 Option Module
Equipo Rockwell-automation 193-EPT E1 PLUS PTC Thermistor Accessory Module Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 193-EPT E1 PLUS PTC Thermistor Accessory Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 193-BC8 Overload Relay Reset Adapter / Anti-Tamper Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 193-EExF_G_H Bul 193 E1 Plus Overload Relay Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 194E-SB_SY Bul 140M / 194E Operating Handle Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 21G PowerFlex 755 AC Drives Cabinet Blower Assembl Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 440R-S845AER-NNL MSR57P GuardMaster Speed Monitori Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 842E EtherNet/IP Absolute Encoder User Manual Manual de usuario
(80 paginas)
(80 paginas)
Equipo Rockwell-automation 440H Rotacam Hinge Operated Safety Interlock Switc Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales