Rockwell-automation 20C PowerFlex 700H Drives Programming Manual de usuario Pagina 53
- Pagina / 116
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 20C-PM001F-EN-P - March 2012 53
Programming and Parameters Chapter 2
INPUTS/OUTPUTS
Digital Inputs
361
362
363
364
365
366
[Digital In1 Sel]
[Digital In2 Sel]
[Digital In3 Sel]
[Digital In4 Sel]
[Digital In5 Sel]
[Digital In6 Sel]
(9)
Selects the function for the digital inputs.
Notes: Options 36…42 are “Reserved”. Added
options 43 and 46 for firmware revision 3.001.
Added options 41, 42, 44 and 45 for firmware
revision 4.001. Added option 68 for firmware
revision 5.002.
(1)
Speed Select Inputs.
To access Preset Speed 1, set [Speed Ref x Sel] to
“Preset Speed 1”.
Type 2 Alarms - Some digital input programming
may cause conflicts that will result in a Type 2
alarm. Example: [Digital In1 Sel] set to “5, Start” in
3-wire control and [Digital In2 Sel] set to 7 “Run”
in2-wire.
Refer to Table 1 on page 64
for information on
resolving this type of conflict.
(2)
When [Digital Inx Sel] is set to option 2 “Clear
Faults” the Stop button cannot be used to clear a
fault condition.
(3)
Typical 3-Wire Inputs - Requires that only 3-wire
functions are chosen. Including 2-wire selections
will cause a type 2 alarm.
(4)
Typical 2-Wire Inputs - Requires that only 2-wire
functions are chosen. Including 3-wire selections
will cause a type 2 alarm. See Table 1 on page 64
for conflicts.
(5)
Auto/Manual - Refer to the Installation Manual for
details.
(6)
Opening an “Enable” input will cause the motor to
coast-to-stop, ignoring any programmed Stop
modes.
Default:
Default:
Default:
Default:
Default:
Default:
Options:
4
5
18
15
16
17
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30-33
34
35
36-40
41
42
43
44
45
46
68
“Stop – CF”
“Start”
“Auto/ Manual”
“Speed Sel 1”
“Speed Sel 2”
“Speed Sel 3”
“Not Used”
“Enable”
(6)(8)
“Clear Faults”(CF)
(2)
“Aux Fault”
“Stop – CF”
(8)
“Start”
(3)(7)
“Fwd/ Reverse”
(3)
“Run”
(4)(8)
“Run Forward”
(4)
“Run Reverse”
(4)
“J og 1”
(3)
“Jog For ward”
(4)
“Jog Reverse”
(4)
“Stop Mode B”
“Bus Reg Md B”
“Speed Sel 1”
(1)
“Speed Sel 2”
(1)
“Speed Sel 3”
(1)
“Auto/ Manual”
(5)
“Local”
“Acc2 & Dec2”
“Accel 2”
“Decel 2”
“MOP Inc”
(10)
“MOP Dec”
(10)
“Excl Link”
(10)
“PI Enable”
“PI Hold”
“PI Reset”
“Pwr Loss Lvl”
Reserved
“Jog 2”
“PI Invert”
“Reserved”
“UserSet Sel1”
(10)
“UserSet Sel2”
(10)
“Run Level”
(11)
“RunFwd Level”
(11)
“RunRev Level”
(11)
“Run w/Comm”
(11)
“Manual/Auto”
(12)
100
156
162
096
141
143
195
194
124
(7)
A “Dig In ConflictB” alarm will occur if a “Start” input is programmed without a “Stop” input.
(8)
Refer to the Sleep Wake Mode Attention statement on page 33.
(9)
A dedicated hardware enable input is available via a jumper selection. Refer to Installation Manual for
further information.
(10)
Refer to [Dyn UsrSet Sel] on page 37 for selection information.
(11)
Refer to Selected Option Definitions – [Analog Outx Sel], [Digital Inx Sel], [Digital Outx Sel] on page 55.
(12)
The function of this value is similar to 18 “Auto/Manual”, except the polarity is opposite.
File
Group
No.
Parameter Name & Description Values
Related
321Auto Reference Source
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Reference A
Reference B
Preset Speed 2
Preset Speed 3
Preset Speed 4
Preset Speed 5
Preset Speed 6
Preset Speed 7
- Programming Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Appendix B 6
- Application Notes 6
- Appendix C 6
- Who Should Use this Manual 7
- What Is Not in this Manual 7
- Additional Resources 8
- General Precautions 8
- Drive Start-Up 11
- Start-Up the Drive 12
- Running S.M.A.R.T. Start 13
- Running an Assisted Start Up 13
- Chapter 1 Drive Start-Up 14
- Programming and Parameters 15
- How Parameters are 17
- Organized 17
- Inputs & Outputs 18
- Motor Control 18
- Speed Command 18
- Dynamic Control 18
- Communication 19
- Inputs/Outputs 19
- File Group Parameters 19
- Monitor File 20
- Motor Control File 21
- Speed Command File 24
- Dynamic Control File 30
- (1)(2)(3) 33
- Utility File 35
- Communication File 45
- Inputs/Outputs File 49
- Parameter List by Name 56
- Parameter List by Number 58
- Troubleshooting 61
- Drive Status 62
- Faults and Alarms 63
- Manually Clear Faults 63
- Fault and Alarm Descriptions 64
- Fault Subcodes 71
- Subcodes 75
- Clear Alarms 77
- Common Drive Symptoms 77
- Motor Operation is Unstable 78
- Technical Support Options 79
- HIM Overview 81
- LCD Display Elements 82
- ALT Functions 82
- Figure 2 - HIM Menu Structure 83
- View and Edit Parameters 85
- Remove and Install the HIM 86
- Motor Control Technology 88
- Trip Time (Sec) 89
- Frequency 91
- Vector Control Option 93
- (currently not available for 93
- PowerFlex 700H drives) 93
- PI Enable 94
- Normalized Feedback 95
- Reverse Speed Limit 96
- Skip Frequency 97
- Sleep Wake Mode 99
- Appendix B Application Notes 100
- Start At Power Up 101
- Stop Modes 101
- (A)(C)(B) 102
- History of Changes 103
- Appendix C History of Changes 106
- Numerics 107
- Rockwell Automation Support 116
- Documentation Feedback 116
Relacionado con productos y manuales para Equipo Rockwell-automation 20C PowerFlex 700H Drives Programming
Equipo Rockwell-automation 20D PowerFlex 700 Installation Instructions - Fram Manual de usuario
(76 paginas)
(76 paginas)
Equipo Rockwell-automation 20L PowerFlex 700L Liquid-Cooled Adjustable Freque Manual de usuario
(156 paginas)
(156 paginas)
Equipo Rockwell-automation 140G-K-TLAx_TLCx_MTLx Cu/CuAl Terminal Lug Install Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 42D Series 5000 Blue Line with Analog Output Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 20P PowerFlex DC Drive - Frame D Discharge Resisto Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 42JT_JS VisiSight Competitive Replacement Kit Inst Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 20D-DL2-LEBO DriveLogix5730 Logix Expansion Board Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 20-COMM-D DeviceNet Adapter Series B FRN 2.xxx Manual de usuario
(246 paginas)
(246 paginas)
Equipo Rockwell-automation 42DBS-5100 Background Suppression with Timing PHOT Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 20L PowerFlex 700L Frame 2 Common Mode Choke Kit Manual de usuario
(4 paginas)
(4 paginas)
Samsung AOK-200CAN manuali
Manuali dei proprietari e guide per l'utente per no Samsung AOK-200CAN.
We fornisce 1 manuali pdf Samsung AOK-200CAN per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Comentarios a estos manuales