Rockwell-automation 2755-DM9, -DM9E High Speed Decoder Manual de usuario Pagina 18
- Pagina / 167
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2
Description of Hardware
2–8
The decoder will accept line voltages from 85 to 264 volts AC at a frequency
of 47 to 63 Hz without any adjustments. The Catalog No. 2755-DM9
decoder is supplied with a 120VAC rated power cord. If you are powering a
2755-DM9 decoder with a supply voltage greater than 120 VAC, you must
obtain a suitable power cord.
Note: Catalog No. 2755-DM9E is supplied with an unterminated power cord.
Attach a suitable connector using the diagram provided in Chapter 5.
A 15 pin D connector is provided on the decoder for connecting the laser
scan head. You can connect the decoder to the scan head using one of the
following:
• For Catalog No. 2755-L7 and -L9 scan heads use-
10 foot (3.05 meter) cable (Catalog No. 2755-CL10)
25 foot (7.62 meter) cable (Catalog No. 2755-CL25)
• For Catalog No. 2755-L4 and -L5 scan heads use-
10 foot (3.05 meter) cable (Catalog No. 2755-CK10)
25 foot (7.62 meter) cable (Catalog No. 2755-CK25)
Note: The scan head is powered by the decoder through the cable. The scan
heads do not require a separate power source.
90-061-4
Figure 2.5
Input Power and Scan Head Connectors
Power and Scan Head
Connectors
- Bulletin 2755 1
- High Speed Decoder 1
- • identify a hazard 2
- • avoid the hazard 2
- • recognize the consequences 2
- Using This Chapter 3
- Installing the Decoder 4
- Communicating With a Host 4
- Host Commands Using a 5
- RS-232 or RS-422 Interface 5
- Host Commands Using the 5
- RS-485 Interface 5
- Table of Contents 6
- Using This Manual 8
- Intended Audience 9
- Conventions Used 9
- Warnings And Cautions 10
- Nomenclature 10
- Related Publications 10
- Description of Hardware 11
- Laser Scan Heads 12
- Physical Description 12
- Indicators 13
- Chapter 2 14
- Description of Hardware 14
- Figure 2.2 14
- LED Indicators 14
- Communications Ports 15
- -- 120 VAC 240 VAC 17
- -- 200 V/ usec 200 V/ usec 17
- -- 4.0 A Peak 4.0 A Peak 17
- Power and Scan Head 18
- Connectors 18
- Accessories 19
- How the Decoder Operates 20
- DC Output Module Application 21
- Communications 22
- RAM and EEPROM Memory 25
- Operating Modes 26
- Trigger Ending Coditions 27
- Response Modes 27
- Configuring Your Decoder 28
- Programming Terminal Cable 29
- Menus and Setup Screens 29
- Start-up Procedure 29
- Chapter 4 30
- Select Operation Menu 31
- (Continued) 32
- Using and Editing the 36
- Configuration (Setup) Screens 36
- Command Bar 39
- Setup Screen #1 41
- Setup Screen #1 Fields 44
- Data Check Characters 46
- Host Communications 47
- Package Detect Input 50
- Setup Screen #2 51
- Setup Screen #2 Fields 53
- Code Lengths 54
- • No-read timer times out 55
- Match Code Table 61
- Programming Example 65
- Chapter 5 76
- Determining the Space 77
- Requirements 77
- Figure 5.3 78
- How to Connect Your Equipment 79
- Installing and Wiring Modules 80
- DC OUTPUT MODULES 81
- • RS-232: no flow control 85
- RS-422 Interface 86
- RS-485 + Transmit/Receive 88
- RS-485 - Transmit/Receive 88
- have the 88
- Message Format 89
- Example Data Messages 91
- Host Commands 92
- Two Character Commands 94
- C D H I M N O P R S 94
- Responses to Commands 95
- 1. Set Code 39, I 2 of 5 and 97
- Codabar Check Characters 97
- 2. Clear Output Counter 97
- 5. Set Host Communications 99
- 6. Write Header Message 100
- 7. Set Package Detect Input 101
- Filter and Sense 101
- 10. Set Message Format 102
- 9. Read Output Counter 102
- Interface 103
- Chapter 7 103
- 11. Read Match Code Table 104
- 12. Write Match Code Table 105
- 14 Write No-READ Message 106
- Read No-Read Count 107
- 16. Set Output Condition and 107
- Output Duration 107
- 17. Clear Package Count 108
- 18. Read Package Count 109
- 19. Reset Decoder 109
- Values, Save to EEPROM and 109
- 21. Save Configuration to 110
- EEPROM and Restart 110
- 22. Save Configuration to 110
- EEPROM (No Restart) 110
- 23. Set Scanner Control 111
- 24. Set Bar Code Specific 112
- Chapter Objectives 113
- RS-485 Command Protocols 113
- RS-485 ASII Command Protocol 113
- RS-485 PCCC Command 114
- Protocol 114
- 00001000 115
- PCCC Commands 116
- 00000001 117
- 01000001 119
- Unprotected Read Example 120
- HI Byte LOW Byte 120
- 01001000 123
- 00000110 126
- 01000110 127
- DIAGNOSTIC LOOP REPLY 130
- (SAME DATA AS COMMAND) 130
- RESET COUNTERS REPLY 130
- Power Input Fuse Replacement 132
- Module Fuse Replacement 133
- Troubleshooting 134
- Specifications 136
- Output Modules 137
- Input Modules 137
- Using a Lear Siegler ADM 3E 138
- Terminal for Programming 138
- Using a DEC-VT100 for 139
- Programming 139
- Using a Catalog Number 140
- 1784-T45 Terminal for 140
- Default Parameters of Decoder 143
- ASCII Conversion Table 145
- Configuration Areas of Memory 146
- Protocol Selection 153
- Transmission Check 154
- Glossary 156
- Cautions and warnings 160
- T45 terminal 165
- Warnings and cautions 166
- With major offices worldwide 167
Relacionado con productos y manuales para Equipo Rockwell-automation 2755-DM9, -DM9E High Speed Decoder
Equipo Rockwell-automation 7000 PowerFlex Medium Voltage Line Filter Capacito Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation 2711E-ND7 PanelView File Transfer Utility User Man Manual de usuario
(109 paginas)
(109 paginas)
Equipo Rockwell-automation 1799-D12G12GL 12 Input/12 Output Discrete Embedded Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 2080-REMLCD Micro800 Remote LCD Installation Instr Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 2727-TRSP1xx MobileView Tablet Power Kit Installat Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 2099-K7KCB-1 Kinetix 7000 DC-DC Converter and Cont Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 2099-BM-xxx Remove Jumpers in Kinetix 7000 Drives Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 2727-TRS74xx MobileView Tablet Quad Charging Stati Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 2711-ND3 PanelBuilder32 Quick Start Manual Manual de usuario
(120 paginas)
(120 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales