Rockwell-automation 8510 AC Spindle Drive System User Manual Manual de usuario Pagina 94
- Pagina / 154
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Wiring
Chapter 8
8-90
Figure 8.9
Orient Feedback Wiring
CN2-1
FG1
CN2-19
AA
CN2-13
AA Return
CN2-18
CN2-12
AB
AB Return
CN2-17
CN2-11
AZ
AZ Return
CN2-5
+12V DC
CN2-3
GND
Mag
Sensor
CN2-1
FG1
CN2-16
DA
CN2-10
GND
CN2-15
CN2-9
DB
GND
CN2-14
CN2-8
DZ
GND
CN2-5
+12V DC
CN2-4
GND
845T
Encoder
845T Wiring High Resolution Magnetic Sensor Wiring
Dual Winding Motor Contactor Control Wiring
When a dual winding 1327AD series motor is used with the 8510, the user
must supply two power contactors that will be used to switch the motor
between the ∆ and Y winding configurations. In addition, a 24V DC power
source must be supplied to operate the contactors. Refer to Table 7.A for
the specific contactors that are required for each drive size. The drive will
control the operation of these contactors through the 20 pin CN1 connector
(see Figure 7.3 for location).
The interface cable for this function requires four twisted pairs. The
recommended cable is:
Madison #08CFJ00004 (4 twisted pairs with shield, #24 AWG)
Three termination options are available for the CNl connector: l) a mating
connector kit, 2) a termination panel, and 3) an interface cable assembly.
The following table shows the I/O function assignment for each of these
termination options.
- 8510 AC Spindle 1
- Drive System 1
- Important User Information 2
- 8510 User Manual 3
- Table of Contents 3
- Introduction 10
- Chapter 1 10
- Specifications 13
- Chapter 2 14
- Dimensions 21
- Chapter 3 22
- DIGITAL AC SPINDLE DRIVE 28
- Mode Scroll + SelectScroll – 28
- Flange Mount Motor 30
- Foot Mount Motor 31
- Chapter 4 42
- Drive Installation 47
- Chapter 5 48
- Figure 5.1 49
- Gasket Assembly 49
- Figure 5.2 50
- Heat Sink Cover 50
- Table 5.A 52
- Motor Installation 55
- Table 6.A 56
- Interface Signal Descriptions 57
- Chapter 7 58
- Chapter 8 78
- Motor Power Terminal Block 85
- Fan Power Terminal Block 85
- AMP Connector 85
- 8510 Drive 97
- Start-Up 100
- Chapter 9 100
- Figure 10.1 107
- “Display Type” Menu Tree 107
- LCD Display 108
- Figure 10.2 108
- Figure 10.3 109
- 8510 Keypad and Display 109
- Figure 10.4 110
- Display Type Menu Tree 110
- Chapter 10 111
- Table 10.A 112
- I/O Inputs 112
- Table 10.B 113
- I/O Outputs 113
- End of Chapter 114
- Diagnostics/Troubleshooting 115
- Troubleshooting 116
- Chapter 11 116
- Figure 11.1 117
- Circuit Board Locations 117
- Coast to Stop 119
- Table 11.D 124
- Table 11.D (Continued) 125
- Table 11.E 126
- Table 11.E (Continued) 127
- Table 11.F 129
- Table 11.F (Continued) 130
- Table 11.G 133
- Table 11.G (Continued) 134
- Figure 11.3 139
- Resolver Signals 139
- Figure 11.4 140
- Figure 11.5 142
- Figure 11.6 143
- Figure 11.7 144
- I/O Board – 8510A-A04, A06 144
- Figure 11.8 145
- CPU Board – 8510A-A04, A06 145
- CN16 CN14 146
- Figure 11.10 147
- Power Board – 8510A-A04, A06 147
- Figure 11.11 148
- I/O Board – 8510A-A11, A22 148
- Figure 11.12 149
- Figure 11.13 150
- Power Board – 8510A-A11 150
- Figure 11.14 151
- Power Board – 8510A-A22 151
- Appendix 152
- 8510A-A22-xx Drive 153
Relacionado con productos y manuales para Equipo Rockwell-automation 8510 AC Spindle Drive System User Manual
Equipo Rockwell-automation 2093-PRF Kinetix 2000 Slot Filler Module Installat Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 2727-MRT5_10_15_20 MobileView Connection Cable Ins Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 6180P-xxxx Integrated Display Computers with Keypa Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 2098-DSD-xxx Ultra3000 Digital Servo Drives with D Manual de usuario
(120 paginas)
(120 paginas)
Equipo Rockwell-automation 57C402 25-115V AC/DC Low Power Output Module Manual de usuario
(34 paginas)
(34 paginas)
Equipo Rockwell-automation 2085-IA8_IM8_OA8 Micro800 8-Point Input and 8-Poin Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 2094 2094 Mounting Bracket Installation Instructio Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2100 CENTERLINE MCC Installing Unit Load Ground Lu Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 2364,2364E NRU Diode Bridge Assembly Replacement ( Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 2711C-xxxx PanelView Component HMI Terminals Insta Manual de usuario
(36 paginas)
(36 paginas)
Equipo Rockwell-automation 2364, 2364F Regenerative DC Bus Supply Unit (RGU) Manual de usuario
(10 paginas)
(10 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales