Rockwell-automation 2706-ND1 DL40 OFFLINE PROGRAMMING SFTWR.USER MANUA Manual de usuario Pagina 35
- Pagina / 139
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3
Installing the Software
3–9
10 If you are using the 1770-KF2 communications interface card, the
contents of the CFG_KT.INI file should be similar to the format shown in
the sample file below:
[DTL_KT.Options]
PATH=C:\ABIC\BIN
[DTL_DF1.1]
DEVICE=DF1
BAUD=9600
IRQ=4
COM_PORT=2
NAME=DTL_DF1
ERROR=1 ①
PARITY=0 ②
DUPLEX=1 ③
① 0=BCC,1=CRC
② 0=No Parity, 1=Even Parity
③ 0=Half Duplex, 1=Full Duplex
11 Save the file. If you are using the DOS text editor, type:
[ALT]FXY
If you are using an Ethernet link and want to enable PLC PassThrough file
transfers, you must first modify your CONFIG.SYS and AUTOEXEC.BAT
files, and install and configure the following products on your PC:
• Allen-Bradley Ethernet communications interface card (Cat. Nos.
6628-A5 or -A7) or equivalent
• FTP’s PC/TCP Software for DOS/Windows (FTP Cat. No. PC-210)
Install Ethernet Card
Follow the instructions that came with your Allen-Bradley Ethernet
communications interface card to install and configure it on your personal
computer.
Install the PC/TCP Software
Follow the instructions that came with FTP’s PC/TCP Software to install it
on your personal computer.
Install the Offline Programming Software
Perform the basic installation procedure described earlier in this chapter to
install the Offline Programming Software on your personal computer.
Installing the Software for
Ethernet PLC PassThrough
- (Cat. No. 2706-ND1) 1
- Important User Information 2
- Overview 3
- The Develop Menu 4
- User Manual 5
- Table of Contents 5
- Conventions Used 10
- Related Publications 11
- Introduction to the DL40 12
- Main Features 13
- Chapter 2 14
- Onboard Editor 16
- Version) 16
- Backup Operations 16
- Operating Modes 20
- Special Messages 23
- System Requirements for 23
- Remote I/O Without 23
- PassThrough File Transfers 23
- Catalog Numbers 25
- Compatible Keyboards 25
- Options & Accessories 26
- Installing the Software 27
- Memory Management 28
- Installation 29
- Basic Installation 29
- (Without PassThrough file 29
- Installing the Software for 30
- DH+ PLC PassThrough 30
- Create CFG_KT.INI File 32
- Ethernet PLC PassThrough 35
- Restart Your PC 36
- must be 37
- Starting the Program 37
- Establishing Initial 37
- Communications In 37
- Non-Networked Installations 37
- Navigating the Software 38
- Figure 4.1 39
- Opening screen 39
- Figure 4.2 39
- Main screen 39
- Getting Help 40
- The Setup Menu 41
- Chapter 4 42
- Setting Time & Date 43
- Menu Key Control 44
- Shortcut Keys 44
- Exiting the Program 45
- Chapter 5 47
- File Selections Screen 48
- Create New File Pop-up 49
- Data Path Directory Pop-up 50
- Develop Screen Menu Bar 51
- Messages Menu 53
- Edit Message Screen 54
- Message Text Window 55
- Any alphabetic or numeric key 56
- More about variables 57
- Create New Message 60
- Copy (Messages) Screen 61
- Delete (Message) Screen 63
- Renumber (Messages) 64
- Text Search Screen 66
- Modify Message Attributes 68
- • any Special Message runs 72
- Message Attribute Default 76
- Options Menu 78
- Ports Menu 80
- Verify Menu 83
- Communications via RS–485 85
- Communications via RS–232 86
- Message text window 87
- Downloading a File Via 91
- RS-232 or RS-485 91
- Uploading a File 95
- Via RS-232 or RS-485 95
- Uploading a File Via 100
- Remote I/O (PassThrough) 100
- Creating a New 101
- Communications File 101
- Chapter 6 102
- The Transfer Menu 102
- Selecting a Hardware Device 103
- Modifying an Existing 107
- Sending the Time and Date to 107
- Writing a File to Tape 108
- Drive:\Root\Subdir 109
- Reading a File from Tape 111
- The Reports Menu 112
- Select File Submenu 113
- Configure Ports Submenu 114
- Starting the Print Job 115
- The Files Menu 116
- Special keys 117
- Select Files Menu 118
- File Selections/File Picks 119
- Copy File(s) 120
- Delete File(s) 121
- Rename File(s) 122
- Convert DL20 File(s) 123
- Converting multiple files 124
- Message Display Worksheets 125
- Appendix A 126
- 2706-NC12 127
- 2706-NC13 127
- 2706-NC14 128
- 2706-NC15 128
- DL40 to Allen-Bradley 129
- 1770-SA or -SB Tape 129
- Recorder 129
- ASCII Character Sets 130
- Extended ASCII Character Set 131
- Index – 1 132
- Index – 2 133
- Index – 3 134
- Index – 4 135
- Index – 5 136
- Index – 6 137
- Worldwide representation 139
Relacionado con productos y manuales para Equipo Rockwell-automation 2706-ND1 DL40 OFFLINE PROGRAMMING SFTWR.USER MANUA
Equipo Rockwell-automation 2090-UCSR-P900 900 Watt Passive Shunt Module Insta Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 6180 Pentium Processors (for 6180 Industrial Compu Manual de usuario
(7 paginas)
(7 paginas)
Equipo Rockwell-automation 2099-BMxxx Kinetix 7000 High Power Servo Drive Ins Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 2711-NC2 PanelView Remote Keyswitch/RS-232 Port As Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 6181P-xxxx Integrated Display Computers, Series A Manual de usuario
(72 paginas)
(72 paginas)
Equipo Rockwell-automation 2090-KFBM6-AA Feedback Connector Kit for TL-Series Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation MV SMC Flex OEM Components - SMC Flex Control Modu Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 6189-KEKIT1 Legend Strip Kit for 6180 Industrial C Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 7000A PowerFlex Medium Voltage Drive (A-Frame) - C Manual de usuario
(515 paginas)
(515 paginas)
Equipo Rockwell-automation 4000 Series 4000 LED Universal Control Bases, Open Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales