Rockwell-automation 2711 PANELBUILDER SOFTWARE USER MANUAL Manual de usuario Pagina 220
- Pagina / 468
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Information and Alarm Windows
Chapter 7
7-12
Information Window Acknowledgement
If your application requires that the Information window stay on the screen
until it is acknowledged, choose Enable for the menu item Acknowledge to
PLC Controller. An address definition window opens.
When this option is enabled, the message window is displayed on the
PanelView terminal with an ACK button instead of a Clear button. The
window will stay on the screen until the window control address is set to
zero. If the screen changes, the message window will still be displayed
until the window control address is set to zero. To remove the window, the
PLC controller must detect the ACK bit and then reset the window control
address using ladder logic.
If the Acknowledge to PLC Controller address is assigned, the information
window will function as follows:
When the user acknowledges an information message via the ACK
button, the terminal sets the “Acknowledge to PLC Controller” bit. The
bit stays on for up to 3 seconds, or until the window control bit resets to 0.
Use an Alarm window when you want the PLC controller to trigger the
display of an important message such as:
alarm condition messages
warnings
informative messages
There are two types of Alarm window:
a “single-line” Alarm window without buttons which displays the most
recent alarm, while leaving the current screen’s buttons active for
operator input
a “Full” Alarm window with a set of buttons for operator response to
alarms. When the Full Alarm window is on the screen, all other buttons
on a keypad terminal are temporarily inoperative, until the operator
responds to the alarm. On a touch screen terminal, only those touch cells
that are covered by the Alarm window are disabled
IMPORTANT: Do not confuse the Alarm window with the Alarm
History Screen.
The Alarm Window
- Catalog Number 2711-ND1 1
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Table of Contentsii 4
- Planning 5
- Creating 6
- A Sample Application File 6
- Table of Contents v 7
- Table of Contentsvi 8
- Table of Contents vii 9
- Table of Contentsviii 10
- Manual Overview 11
- Intended Audience 11
- Glossary of Terms 11
- Related Publications 13
- AfterSales Support 14
- Introduction to PanelBuilder 15
- Chapter 1 18
- Objects, Windows, and PLC 19
- Controlled Options 19
- Objects Common to All 21
- PanelView Terminals 21
- Objects for the Keypad 23
- Terminal 23
- Applicable Programmable 25
- Controllers and Connections 25
- PLC5/10 Processor 26
- PLC3 and PLC3/10 Processors 26
- 6008SQ DEC QBUS I/O Scanner 28
- Installing PanelBuilder 29
- Chapter 2 30
- PanelBuilder Files 30
- The DEFAULTS File 31
- Version Compatibility 33
- PanelView Default Settings 35
- Figure 2.3 36
- PanelView Firmware V 36
- Using PanelBuilder 37
- Chapter 3 38
- Data Entry Keys 38
- PanelBuilder Menu Structure 42
- The Main Menu 42
- The Develop Menu 43
- The Transfer Menu 44
- The Reports Menu 45
- The Files Menu 45
- The Setup Menu 46
- The Exit Menu 48
- The File Menu 48
- The Screens Menu 49
- The Windows Menu 49
- The Options Menu 51
- The Communications Menu 55
- The Screen Menu 56
- The Edit Menu 58
- Move, Delete, and Memorize 58
- The Object Menu 62
- Move and Size 64
- States and Text 68
- Text and Outer Text 69
- Buttons and Keypad Terminals 72
- Button Concepts 72
- Buttons and AutoRepeat 74
- Button Location 77
- Considerations 77
- Figure 4.1 78
- with Alarm W 78
- Block Transfers 79
- Determining Rack and Block 80
- Transfer Needs 80
- Reducing PLC Addressing 81
- Worksheets 82
- Screen Worksheets 84
- The Object Address List 86
- Object Address List and I/O 86
- Usage Worksheets 86
- The I/O Usage Worksheets 87
- Example: BCD Values or States 93
- Number of Bits 94
- PLC Communications 95
- Worksheet 95
- PLC/Scanner Type 96
- Baud Rate 96
- Rack Assignments 96
- Block Transfer Assignments 97
- Estimating PanelView Terminal 98
- Memory Requirements 98
- Object Memory Usage 99
- Planning Your Application 100
- Chapter 4 100
- *********** 111
- ************ *** 111
- Create the Application File 114
- Chapter 115
- Start up PanelBuilder 115
- Chapter 5 116
- Define PLC Type 117
- Step 2: Configure PLC 117
- Communications 117
- Define Rack Assignments 118
- Define Block Transfer Files 120
- Set the Baud Rate 121
- Screen 1: MAIN SCREEN 122
- Step 3: Create the Screens 122
- Screen 2: CONVEYOR CONTROLS 134
- Screen 3: PUMP CONTROLS 155
- File Operations 175
- Chapter 6 176
- Saving Files 176
- Printing Reports 177
- Computer 185
- CONFIGURATION MODE MENU 186
- Downloading Considerations 188
- Uploading from PanelView 189
- Downloading and Uploading 190
- PASS-THROUGH 195
- DOWNLOAD OPTIONS 195
- Burn EPROMS 204
- Burning the User EPROM 204
- Burn Single EPROM 206
- Programming EEPROMs 207
- Burn EEPROMS 208
- Information and Alarm Windows 209
- Chapter 7 210
- Creating Messages 211
- Editing Messages 214
- Copying Messages 215
- Deleting Messages 215
- The Alarm Window 220
- Alarm Messages 221
- Configuring the Alarm Window 223
- FFFnnn“ttt...ttt” 225
- Number Address Bit 236
- Acknowledge Button Address 237
- Remote Window Processing 237
- Alarm History Screen 241
- The Alarm Status Screen 243
- Alarm Status Screen Buttons 249
- Viewing the Display 249
- Screen Operations 253
- Chapter 8 254
- Security 255
- The Powerup Screen 256
- Application File Comment 257
- PLC Controlled Options 258
- Chapter 9 259
- Assigning Addresses 259
- Time and Date to PLC 260
- Controller 260
- Table 9.A 261
- About Screen Prints 263
- PLC Controlled Screen Print 263
- PLC Controlled Time and Date 264
- Other PLC Controlled Options 265
- The Objects 266
- Chapter 10 267
- Retentive Objects 267
- The Add Menu 268
- Push Buttons 269
- Latched Push Button 271
- Maintained Push Button 272
- Interlocked Push Button 273
- Control Selectors 274
- Go To Screen" Button 283
- Screen Selectors 283
- Screen List Selector 284
- (Touch Screen Terminals Only) 285
- Screen KeypadEnable Button 286
- (Keypad terminals only) 286
- MultiState Indicator 287
- Indicators 287
- List Indicator 288
- Numerics 290
- Set Value Button 291
- Increment Value Button 292
- Decrement Value Button 293
- Numeric Data Display 295
- Standard Numeric Data Display 295
- Scaled Numeric Data Display 297
- Example: Scaling Formula 298
- (Touch Screen terminals only) 302
- J NNN.N J 314
- Text/Draw 315
- Bar Graphs 321
- Time Display 322
- Time and Date 322
- Date Display 323
- Local Message Display 323
- Screen Print Button 328
- ASCII Display 329
- Invalid Control Sequences 333
- ASCII Input Object 333
- Scrolling List Object 343
- Figure 10.22 344
- Scrolling List Screen 344
- Object List 350
- Button Operation 358
- About Retentive Objects 359
- Retentive Objects and Presets 360
- Testing Your Application File 362
- Chapter 11 363
- Test Retentive Objects 363
- Connecting the Programmable 363
- Testing the Whole System 364
- Appendix 365
- Rack Number 365
- Module Group (Word) 365
- Block Transfer Programming 365
- Appendix A 366
- Byte (slot) 366
- Number of Words 366
- PLC3 Block Transfer 370
- Programming Examples 370
- Figure A.7 374
- Bidirectional 374
- Using PLC2s and a 1771SN 376
- Subscanner with PanelView 376
- Ladder Program for Remote I/O 379
- Discrete Data Response Time 379
- System Response Times 379
- PLC5 Block Transfer Timing 382
- = Wait time in Queue 382
- SLC 5/02 Programming 385
- Scrolling List Example 389
- Step 3: Program the PLC 394
- Troubleshooting 406
- Appendix B 407
- PanelBuilder Problems 407
- * in Table B.A 408
- PanelBuilder Error Messages 408
- PanelView Error Messages 409
- PLC Communication Problems 411
- PassThrough 412
- Upload/Download Problems 412
- Sample Worksheets 414
- ISA Symbols 415
- Appendix D 416
- Electrical 419
- Containers and Vessels 420
- Rotating Equipment 424
- Material Handling 426
- Heat Transfer Devices 428
- Miscellaneous 429
- The Extended Character Set 430
- Appendix E 431
- Screen Name: 441
- Application File Name: 441
- Screen Number: 441
- Object Address List 445
- Discrete I/O Usage Worksheet 447
- Number of Words: 449
- PLC Communications Worksheet 451
- With major offices worldwide 468
Relacionado con productos y manuales para Equipo Rockwell-automation 2711 PANELBUILDER SOFTWARE USER MANUAL
Equipo Rockwell-automation 2727-T7P30D1F MobileView Tablet T750 User Manual Manual de usuario
(104 paginas)
(104 paginas)
Equipo Rockwell-automation 7000 PowerFlex Medium Voltage AC Drive (B Frame) - Manual de usuario
(495 paginas)
(495 paginas)
Equipo Rockwell-automation Atlas 5-GD2 Heavy Duty Guard Locking Interlock Saf Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2198-Hxxx Kinetix 5500 Servo Drives Installation I Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 7000 PowerFlex Medium Voltage Line Filter Capacito Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation 2711E-ND7 PanelView File Transfer Utility User Man Manual de usuario
(109 paginas)
(109 paginas)
Equipo Rockwell-automation 1799-D12G12GL 12 Input/12 Output Discrete Embedded Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 2080-REMLCD Micro800 Remote LCD Installation Instr Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales