Rockwell-automation 2711 Standard PanelView Operator Terminal User Man Manual de usuario Pagina 256
- Pagina / 292
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
256 Publication 2711-UM014G-EN-P - September 2008
Appendix B Messages, Codes and Self-test Numbers
Remote I/O Terminal Messages
EtherNet/IP Messages
For a description of EtherNet/IP terminal codes, see page 263.
Error Number Terminal
Messages
Type Meaning Recommended Action
661 Timeout - No
Block Transfer
Writes
Comm Status The PLC is communicating with the
terminal, but the PanelView is not
receiving BTW requests required by
the application.
Check ladder logic for missing BTW
instructions (instructions are not
enabled) or addressing errors. Check
for logic controller errors.
662 Timeout - No
Block Transfer
Reads
Comm Status The PLC is communicating with the
terminal, but the PanelView is not
receiving BTR requests required by
the application.
Check ladder logic for missing BTR
instructions (instructions are not
enabled) or addressing errors. Check
for logic controller errors.
663 Timeout - No
Block Transfer
Requests
Comm Status The PLC is communicating with the
terminal, but the PanelView is not
receiving BTR or BTW requests
required by the application.
Check ladder logic for missing BTR or
BTW instructions (instructions are not
enabled) or addressing errors. Check
for logic controller errors.
664 PLC in program
mode
Comm Status The PLC is offline (in Program Mode).
The COMM Status indicator on the
Configuration Mode menu is off.
Place the PLC in run mode to resume
communication.
665 No PLC
communication
Comm Status The PLC is not communicating.
Possible causes are disconnected
cable, no power to PLC, incorrect
baud rate or rack settings for PLC
configuration. COMM Status
indicator is off.
Check for pulled cables and PLC
power. Check baud rate settings and
rack configurations.
Check wiring of connector.
Communication resumes when
problem is corrected.
666 Invalid Rack
Configuration
Comm Status No communication can occur because
of an invalid rack configuration.
Correct the RIO rack configuration.
667 Remote I/O
Hardware Failed
Comm Status During startup, the terminal detected
a missing, corrupt or nonfunctional
remote I/O card. The terminal will run
but not communicate.
Contact technical support and provide
specific message.
- PanelView Standard Operator 1
- Terminals 1
- Important User Information 2
- Summary of Changes 3
- Chapter 2 6
- Applying Power and Resetting 6
- Terminal 6
- Chapter 3 6
- Configuring the Terminal 6
- Chapter 4 8
- Chapter 5 8
- Table of Contents 10
- Chapter 12 11
- Terminal Connections 11
- Chapter 13 12
- Appendix A 12
- Specifications 12
- Additional Resources 16
- Technical Support 16
- Terminal Overview 17
- Color and Grayscale Terminals 18
- PanelView 600 Color Terminals 20
- PanelView 900 Color Terminals 22
- Terminal Features 26
- Features 27
- PanelView 550 Terminal 29
- PanelView 600 Terminal 34
- PanelView 900/1000 40
- PanelView 1400 Terminal 44
- Applications 48
- Touch Screen Operation 49
- Keypad Operation 49
- Configuration Mode Menu 50
- Terminal Messages 50
- Alarm List 51
- Accessories 52
- Antiglare Overlay 53
- Remote I/O or DH+ Cable 55
- Replacement Parts 56
- Panel Mount Clips and Studs 57
- Remote I/O Connector 57
- Power Input Connector 57
- Wiring and Safety 59
- Guidelines 59
- Connect AC Power 61
- PanelView 900/1000 Terminal 62
- Connect DC Power 63
- Explosion Hazard 64
- Reset the Terminal 66
- Power-up Sequence 67
- For Remote I/O Terminals 68
- Access the Configuration 72
- Mode Menu 72
- Select a Language 73
- Use a Memory Card 74
- Configure Communication 75
- Max Node 76
- Comm Status Indicator 76
- Fault Status Indicator 76
- DH+ Communication 77
- ControlNet Communication 79
- Restart Terminal 81
- DeviceNet Communication 82
- New Baud 83
- Active Baud (read only) 83
- Bus-off Interrupt 83
- Interscan Delay 83
- DF1 Communication 84
- Communication Parameters 85
- Error Detection 85
- Handshaking 85
- EtherNet/IP Communication 86
- DHCP/BootP Enable 87
- IP Address 87
- Subnet Mask 87
- Configure Presets 88
- Viewing Terminal 89
- Information 89
- Adjust Screen Parameters 90
- Contrast 91
- Video Mode 91
- Screen Saver Mode 91
- Reset Video 91
- Backlight 93
- Backlight Timeout 93
- Normal Intensity 94
- Screen Saver Timeout 94
- Screen Saver Intensity 95
- Set the Time and Date 100
- Set the Time 101
- Set the Date 101
- Set Up the Printer 102
- Port Mode 103
- Baud Rate 103
- Top of Form 103
- Using a Memory Card 105
- Use the Memory Card 106
- Retainer 106
- ATTENTION 107
- Load Application 108
- In progress 109
- Store Font Files 111
- Remove a Memory Card 112
- Running Applications 113
- Screen Security 114
- Push Button Operation 114
- Control Lists 115
- Active Control List 116
- List Keys 117
- Cursor-piloted Control Lists 117
- Numeric Entry Cursor Point 118
- Keypad Enable Button 118
- Scratchpad 119
- ← key in an empty scratchpad 120
- ASCII Entry Controls 121
- Controls Location Function 122
- ↵ to send the string to the 123
- Controls Function 125
- Screen Selectors 126
- Cursor Operation 127
- List Indicators 128
- Multistate Indicators 128
- Bar Graph Displays 128
- Analog Gauges 129
- Numeric Data Displays 129
- Message Displays 129
- Time or Date 130
- Printing 130
- Chapter Objectives 133
- Hazardous Location 133
- Considerations 133
- Enclosures 134
- Required Tools 134
- Mounting Dimensions 134
- Cutout Dimensions 135
- Clearances 135
- Install Terminal in Panel 136
- Installing the PV300 Terminal 139
- Install the PV300 Terminal 143
- Installing the PV550 Terminal 145
- Install the PV550 Terminal 150
- PV550 Touch Screen Terminal 151
- Installing the PV600 Terminal 153
- Install the PV600 in a Panel 158
- PV900 Terminals Mounting 163
- Dimensions 163
- PV1000 Terminals Mounting 164
- Install the 167
- PV900/PV1000 Terminals in 167
- Install the PV1400 Terminal 173
- Cable Charts 178
- Remote I/O Terminal 185
- Connections 185
- Supported Controllers 186
- Making Remote I/O Connections 187
- Remote I/O 188
- Pass-through 188
- DH+ Terminal Connections 189
- Making DH+ Connections 191
- DH-485 Terminal 192
- IMPORTANT 194
- 1761-NET-AIC) 195
- Connecting a Computer 196
- RS-232 (DH-485) Terminal 199
- (Point-to-point) 200
- RS-232 (DF1) Terminal 202
- Compatible Controllers 203
- RS-232 (DF1) Terminal Ports 203
- RS-232/DF1 Port Connector 204
- Using a Modem 206
- ControlNet Connections 207
- ControlNet Protocol 208
- ControlNet Terminal Ports 208
- Typical ControlNet Network 209
- Making ControlNet Connections 210
- NAP and Redundant Cables 211
- DeviceNet Network 212
- Making DeviceNet Connections 213
- Typical DeviceNet Network 214
- EtherNet/IP Connections 215
- Ethernet Connector 216
- PanelView 300 Micro 218
- CompactLogix, or FlexLogix 219
- PanelBuilder32 Software 222
- Connecting a Computer or 223
- Printer to the Terminal 223
- Equipment Required 225
- Use the Troubleshooting 225
- Interpret Status Indicators 229
- Clean the Display Window 231
- Replace the Clock Module 232
- Replace the Backlight 232
- PanelView 300 Terminal 234
- PanelView 550 Terminals 236
- PanelView 600 Color 238
- Keypad and Touch 238
- Touch Only Terminals 239
- PanelView 900 240
- Monochrome and Color 240
- PanelView 1000 Color & 244
- Grayscale 244
- PanelView 1400 Color 245
- Communication 247
- Agency Certifications 248
- Appendix 249
- Types of Terminal 249
- Messages 249
- General Terminal 250
- DH-485 Terminal Messages 254
- ControlNet Terminal Messages 255
- Remote I/O Terminal Messages 256
- EtherNet/IP Messages 256
- DH+ Terminal Messages 257
- Terminal Codes 258
- General Codes 262
- ControlNet Codes 262
- EtherNet/IP Codes 263
- Remote I/O Communication 267
- Self-test Numbers 267
- Intended Use of Product 270
- Wiring Recommendations 270
- Declarations of Conformity 270
- Glossary 273
- How Are We Doing? 287
- BUSINESS REPLY MAIL 289
- Rockwell Automation 292
Relacionado con productos y manuales para Equipo Rockwell-automation 2711 Standard PanelView Operator Terminal User Man
Equipo Rockwell-automation 2090-UCSR-A300 300 W Active Shunt Regulator Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 6189V-25HDDSA Replacing Hard Disk Drive Shock Moun Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 60-212 PHOTOSWITCH Miniature Universal Control Bas Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 2711P-Rxxxx Logic Module, Internal CompactFlash, a Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 2706-LV2xX, -LV4xX Dataliner DL40 Plus Message Dis Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 2711C-xxxx PanelView Component HMI Terminals Manual de usuario
(146 paginas)
(146 paginas)
Equipo Rockwell-automation 9306 DriveExplorer Software Set Up and Reference C Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 2711P Software Development Kit User Manual Manual de usuario
(104 paginas)
(104 paginas)
Equipo Rockwell-automation 2711 PanelView 1400 Terminals Installation Instruc Manual de usuario
(62 paginas)
(62 paginas)
Equipo Rockwell-automation 2711P-RBxxx Display Module Bezel Replacement Insta Manual de usuario
(28 paginas)
(28 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales