Rockwell-automation 2711P PanelView Plus Terminal User Manual Manual de usuario Pagina 150
- Pagina / 246
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
150 Publication 2711P-UM001J-EN-P - November 2009
Chapter 6 Install and Replace Components
5. Push down on the communication module until the connector is
firmly seated.
6. Tighten the three captive screws that secure the module to the
terminal, starting with the bottom, left screw on the module.
Tighten screws to a torque of 0.34…0.45 Nm (3…4 lb•in).
Follow these steps to replace a communication module.
1. Disconnect power from the terminal.
2. Disconnect the communication cables from the module.
3. Loosen the three screws that secure the communication module
to the terminal.
4. Carefully lift the communication module away from the terminal
and set aside.
5. Install the new communication module.
- PanelView Plus Terminals 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Objectives 9
- Intended Audience 9
- Parts List 9
- Additional Resources 10
- Software and Firmware 10
- Upgrades 10
- Overview 11
- PanelView Plus 400 and 600 12
- Terminals 12
- Base-configured Units 13
- Communication Modules 14
- Power Options 14
- Display and Input Options 15
- Keypad or Keypad and Touch 16
- PanelView Plus 700 to 1500 17
- Modular Components 18
- Base-configured Unit 18
- Display Modules 20
- Touch Screen 21
- Catalog Number 23
- Configuration 23
- PanelView Plus Product 23
- Chapter 1 Overview 24
- Overview Chapter 1 25
- 400 and 600 25
- Installation 31
- Application Information 33
- Environment and Enclosure 34
- Outdoor Installation for 34
- High-bright Displays 34
- Installation Chapter 2 35
- Clearances 36
- Cutout Dimensions 36
- Mount the 400 or 600 37
- Terminal in a Panel 37
- Mount the 700 to 1500 39
- Product Dimensions 41
- PanelView Plus 600 Dimensions 42
- Power Connections 47
- Remove and Install the 48
- Power Terminal Block 48
- 700 to 1500 Terminals 49
- 3-position AC or DC 50
- Terminal Block 50
- 2-position DC Terminal 50
- Block (Series E or later) 50
- DC Power Connections 51
- PanelView Plus 52
- AC/DC Power Supply 52
- (2711P-RxxDx Logic Modules) 53
- Earth/Ground Connection 53
- Connect DC Power 55
- AC Power Connections 56
- Functional Earth Connection 57
- Connect AC Power 58
- Reset the Terminals 59
- Configuration Mode 61
- Navigation Buttons 63
- Enter or Edit Data 64
- Load an Application 65
- Run an Application 66
- Application Settings 66
- Terminal Settings 66
- Configure Communication 67
- Communication Driver 68
- Ethernet Driver 68
- Has no properties to edit 68
- DHPlus Properties 69
- DH-485 Properties 69
- Remote I/O Properties 69
- ControlNet Properties 69
- DeviceNet Properties 69
- Serial Properties 70
- Configure Network 72
- Define an Ethernet IP Address 73
- Define Name Server Addresses 75
- Configure Diagnostics 76
- Remote Log Destination 77
- Message Routing 77
- Manage Files on the 78
- List of files stored 79
- Modify Display Settings 81
- Adjust the Display Contrast 82
- Adjust the Display Intensity 82
- Configure the Screen Saver 83
- Font Linking 85
- Configure Keypad 86
- Keyboard, or Mouse 86
- Configure the Touch Screen 88
- 3. Press OK 89
- Configure Print Options 91
- 4. Press OK when done 92
- Configure Startup Options 93
- Example: 96
- Configure Startup Tests 99
- IMPORTANT 100
- View and Clear the System 101
- Event Log 101
- Display Terminal 102
- Information 102
- Display FactoryTalk View 104
- ME Station Information 104
- Modify the Date, Time, or 105
- Time Zone 105
- Change the Time 106
- Change the Time Zone 107
- Modify Regional Settings 108
- Change the Time Format 110
- Change the Short Date Format 111
- Change the Long Date Format 112
- Chapter Objectives 113
- Windows CE .NET 113
- Architecture 113
- Programs 114
- Operating System 115
- Keyboard Shortcuts 116
- Start Menu and Taskbar 117
- Command Bar 117
- Find Files 118
- Browse Web Pages 118
- PanelView Plus CE Memory 119
- Dynamic RAM 120
- External CompactFlash Cards 120
- USB Mass Storage Devices 120
- Control Panel Applications 121
- Network ID 122
- Password 123
- ActiveSync Connection 124
- Configure Ethernet Connection 124
- PC Connection 125
- Double-tap Sensitivity 126
- Calibration 126
- Keyboard 127
- Key Repeat 128
- Multi-Key/Hold-Off Lockout 128
- Input Panel 129
- Background 130
- Appearance 130
- Backlight 131
- Screen Saver 131
- Extended Diagnostics 132
- Hardware Monitor 134
- Device Name 136
- Copyrights 136
- Date/Time 137
- Regional Settings 137
- Internet Options 139
- Certificates 139
- Remove Programs 140
- Storage Manager 140
- Required Tools 141
- Precautions 141
- Install RAM or Internal 143
- CompactFlash 143
- Install or Replace the Logic 144
- 5…7 lb•in) 145
- Captive Screw 146
- Install or Replace a 147
- Communication Module 147
- Replace the Display 151
- (5…7 lb•in) 152
- Replace the Battery 153
- Replace the Bezel 155
- Touch Screen Connector 156
- Display Module Bezel 156
- Replace the Backlight 158
- Retaining Tab 160
- Backlights 161
- Remove the Product ID 162
- Replace the Keypad Legend 162
- 600 Terminal 163
- Use an External 164
- CompactFlash Card 164
- Terminal Connections 165
- Logic Controller Cable 166
- MicroLogix Controllers 167
- Communication Port 169
- Isolation 169
- USB Ports 170
- Serial Connections 171
- Construct a Null Modem Cable 172
- Modem Connection 172
- Computer Connections 173
- Ethernet Connections 174
- Ethernet Cable 175
- Security Considerations 175
- DH-485/DH+/Remote I/O 176
- Belden 3106A Wire Connections 178
- Single Cable Connection 178
- Multiple Cable Connection 178
- 1784-CP14 Cable 179
- 1761-CBL-PM002 Cable 179
- DH+ Network Connections 180
- Remote I/O Connections 181
- ControlNet Module 182
- Minimum Requirements 183
- ControlNet Connections 184
- DeviceNet Module 185
- Related Information 186
- DeviceNet Protocol 186
- DeviceNet Connections 187
- ATTENTION 190
- Upgrade Firmware 191
- Firmware Upgrade Wizard 193
- Upgrade Firmware with a 194
- Network (Ethernet) 198
- Connection 198
- PanelView Plus 700 201
- Upgrade the Operating 204
- System (OS) 204
- External CompactFlash Card 206
- Troubleshoot the System 207
- Isolate the Problem 208
- Check the System Event Log 209
- Perform Extended Diagnostics 210
- Startup Information 211
- Messages 211
- Startup Sequence 212
- Startup Error Messages 213
- Check Terminal 214
- Components 214
- Ethernet Connnection 217
- Application Does Not Run 218
- Configuration Mode Access 218
- File System Errors 219
- Advanced Diagnostics for 219
- CE Terminals 219
- System Identification Errors 220
- Restart in Safe Mode 221
- Maintenance 223
- Battery Removal 224
- Specifications 225
- Mechanical 227
- Agency Certifications 228
- Compatible USB Devices 229
- Appendix 231
- Download Fonts to 231
- Terminal 231
- PanelView Plus CE 231
- Accessories CD 231
- Machine Edition Fonts CD 232
- Programmable Key Definitions 235
- Rockwell Automation Support 244
- Documentation Feedback 244
- User Manual 245
Relacionado con productos y manuales para Equipo Rockwell-automation 2711P PanelView Plus Terminal User Manual
Equipo Rockwell-automation 2500 CENTERLINE Motor Control Centers Installation Manual de usuario
(100 paginas)
(100 paginas)
Equipo Rockwell-automation 4100-EF04_EF08 4 or 8 Way Encoder Buffer Unit Inst Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation 6185-C_B Industrial 15 12 Inch Monitor User Manual Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation 2080-PS120-240VAC Micro800 Programmable Controller Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1794-XXXX FLEX I/O High-Density Analog Modules Manual de usuario
(90 paginas)
(90 paginas)
Equipo Rockwell-automation 2711-K5Axx_B5Axx PanelView 550 Terminals Installat Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 2097-TB1 I/O Terminal Expansion Block Installation Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 6182 Industrial Computer Installation Instructions Manual de usuario
(92 paginas)
(92 paginas)
Equipo Rockwell-automation 2094-EN02D-M01-S1 Kinetix 6200 and Kinetix 6500 Sa Manual de usuario
(156 paginas)
(156 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales