Rockwell-automation 284D ArmorStart - Safety Version - User Manual Manual de usuario Pagina 43
- Pagina / 320
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3
Bulletin 280/281 Programmable
Parameters
Introduction This chapter describes each programmable parameter and its
function.
Parameter Programming
Each Distributed Motor Controller type will have a common set of
parameters followed by a set of parameters that pertain to the
individual starter type.
Refer to Chapter 6, DeviceNet™ Commissioning for instructions in
using RSNetWorx™ for DeviceNet to modify parameter settings.
Important: Resetting the Factory Default Values Parameter 47,
Set to Defaults, allows the installer to reset all parameters
to the factory default values. It also resets the MAC ID to
its factory default after DeviceNet Power is cycled if
switches are set >63.
Important: Parameter setting changes downloaded to the
ArmorStart™ take effect immediately, even during a
“running” status.
Important: Parameter setting changes made in a configuration tool
such as RSNetWorx for DeviceNet do not take effect in
the ArmorStart until the installer applies or downloads
the new settings to the device.
- Controller — Safety Version 1
- Important User Information 3
- European Communities (EC) 4
- Directive Compliance 4
- Table of Contents 5
- Table of Contents iii 7
- Appendix C 9
- Product Overview 11
- 1-2 Product Overview 12
- Overload Protection 13
- LED Status Indication 15
- Fault Diagnostics 15
- 1-6 Product Overview 16
- Product Overview 1-7 17
- 1-8 Product Overview 18
- Installation and Wiring 19
- Applications 20
- Precautions for Bulletin 284 21
- 2-4 Installation and Wiring 22
- Installation and Wiring 2-5 23
- 2-6 Installation and Wiring 24
- Installation and Wiring 2-7 25
- 2-8 Installation and Wiring 26
- Installation and Wiring 2-9 27
- 2-10 Installation and Wiring 28
- Installation and Wiring 2-11 29
- 2-12 Installation and Wiring 30
- Installation and Wiring 2-13 31
- 2-14 Installation and Wiring 32
- Power and Ground Wiring 33
- 2-16 Installation and Wiring 34
- Terminals 35
- 2-18 Installation and Wiring 36
- Description 37
- ArmorStart Safety with 38
- ArmorConnect Connectivity 38
- Terminal Designations 39
- Wiring and Workmanship 40
- Guidelines 40
- Installation and Wiring 2-23 41
- Compatibility 42
- Grounding 42
- Parameters 43
- DeviceLogix™ Group 44
- DeviceNet Group 49
- ➊ Bulletin 280 products 51
- ➋ Bulletin 281 products 51
- Starter Protection Group 52
- User I/O 56
- Misc. Group 59
- ZIP Parameters 60
- Starter Display 68
- Starter Setup 69
- Chapter 4 71
- 83 Zone #2 Offset 72
- 85 Zone #4 Offset 72
- DeviceLogix Group 73
- User I/O Group 85
- Miscellaneous Group 86
- Drive DeviceNet Group 88
- Display Group 90
- Basic Program Group 95
- Advanced Program Group 100
- Table 4.3 102
- ATTENTION 104
- A10 option 106
- Deceleration 107
- Figure 4.2 110
- Figure 4.1 111
- Figure 4.3 112
- Figure 4.5 114
- Speed Reference 119
- Figure 4.7 121
- Table 4.7 122
- How Step Logic Works 128
- Step Logic Settings 128
- Table 4.9 Digit 3 Settings 129
- Table 4.10 Digit 2 Settings 129
- Frequency 131
- HOA Keypad Operation 133
- Forward/Reverse Function 135
- Direction Arrow Functions 136
- HOA Keypad Operation 5-5 137
- 5-6 HOA Keypad Operation 138
- DeviceNet™ Commissioning 139
- Node Commissioning using 140
- Software 140
- DeviceNet™ Commissioning 6-3 141
- 6-4 DeviceNet™ Commissioning 142
- Tool Inside RSNetWorx for 143
- DeviceNet 143
- 6-6 DeviceNet™ Commissioning 144
- Using Automap feature with 145
- Assemblies 145
- Assembly Formats 145
- Setting the Motor FLA and 146
- DeviceNet™ Commissioning 6-9 147
- 6-10 DeviceNet™ Commissioning 148
- Chapter 7 149
- Programming the 155
- 1756-ControlLogix 155
- Explicit Messaging with 156
- ControlLogix 156
- Figure 7.4 Scanner Path 158
- Using DeviceLogix™ 161
- DeviceLogix Programming 162
- Using DeviceLogix™ 8-3 163
- 8-4 Using DeviceLogix™ 164
- ArmorStart® ZIP Configuration 165
- Mapping Consumed Data to the 167
- DeviceLogix Data Table 167
- ZIP 16 = Zone 1: Tripped 168
- ZIP 17 = Zone 1: Warning 168
- ZIP Example 169
- ArmorStart at node 10 171
- Data Table mapping 174
- Diagnostics 177
- Table 10.1 Fault Indication 178
- Diagnostics 10-3 179
- 10-4 Diagnostics 180
- Troubleshooting 181
- 11-2 Troubleshooting 182
- Distributed Motor Controllers 183
- Fault Definitions 186
- Motor Controllers 187
- 11-8 Troubleshooting 188
- Troubleshooting 11-9 189
- 11-10 Troubleshooting 190
- Internal Drive Faults 191
- 11-12 Troubleshooting 192
- NETWORK STATUS LED 195
- Control Module Replacement 196
- (Bulletin 280/281) 196
- (Bulletin 284) 197
- Base Module Replacement 198
- 11-22 Troubleshooting 202
- Troubleshooting 11-23 203
- Source/ Control Brake Fuses 203
- 11-24 Troubleshooting 204
- Specifications 205
- Bulletin 280/281, Continued 206
- Class 10 208
- Class 15 208
- Class 20 208
- Bulletin 284 209
- Bulletin 284, Continued 210
- Pin 1: L1 - Black 212
- Pin 2: GND - Green/Yellow 212
- Pin 3: L2 - White 212
- Pin 1: GND - Green/Yellow 213
- Pin 2: BR+ - Black 213
- Pin 3: BR- - White 213
- ArmorConnect™ Three-Phase 214
- Power Media 214
- Drop Cables 215
- Power Tees & Reducer 216
- Dimensions 217
- Power Receptacles 218
- Pinout and Color Code 219
- A-16 Specifications 220
- Appendix B 221
- DeviceNet object classes: 222
- Identity Object — CLASS CODE 223
- Message Router — CLASS CODE 223
- Assembly Object — CLASS CODE 225
- Custom Parameter Based 225
- “Word-wise” I/O Assemblies 225
- “Word-wise” Bit-Packed 226
- Standard Distributed Motor 227
- Controller I/O Assemblies 227
- Network Outputs and ZIP CCV 229
- CLASS CODE 0x0008 234
- CLASS CODE 0x0009 ➊ 235
- Discrete Output Point Object 236
- Special Requirements 236
- Unbound DOP Instances 1 and 2 238
- 1 = momentary 239
- CODE 0x0010 242
- Discrete Input Group Object — 243
- Class CODE 0x001D 243
- CLASS CODE 0x001E 244
- CODE 0x0029 245
- Acknowledge Handler Object — 246
- CLASS CODE 0x002b 246
- Overload Object — CLASS CODE 247
- CODE 0x00B4 248
- Bulletin 284 CIP Information 249
- Identity Object 251
- Table C.8 Allocation_byte 252
- Instance 254
- Table C.21 ODVA Starter 256
- Controller 256
- Outputs 259
- Table C.32 Logic Command 260
- Point Object: 267
- Protection Fault 269
- Mode set to 1 = momentary 272
- Mode set to 1 = maintained 273
- Interface Object 280
- Group Motor Installations 281
- 8 AWG motor branch trunk 284
- D-6 Group Motor Installations 286
- D-8 Group Motor Installations 288
- Appendix E 289
- ArmorBlock® Guard I/O™ 290
- Safety Function Definition 292
- PLC Program 293
- Replacement 294
- 1732DS-IB8XOBV4 Safety Module 295
- Accessories 297
- Renewal Parts 301
- 280 D – F NS – 10 – C 302
- Structure 303
- Base Module Renewal Part 304
- Product Selection 304
- PID Setup 305
- H-2 PID Setup 306
- PID Reference and Feedback 307
- PID Deadband 307
- PID Enabled 308
- Freq Cmd 308
- PID Output 308
- PID Pre-load Value 308
- PID Pre-load Value > 0 308
- PID Setup H-5 309
- PID Feedback 310
- PID Reference 310
- Counter Functions 311
- Step Logic Sequence 312
- Step Logic Using Basic Logic 313
- Functions 313
- Step Logic Parameters 315
Relacionado con productos y manuales para Equipo Rockwell-automation 284D ArmorStart - Safety Version - User Manual
Equipo Rockwell-automation 814S-W3-480V-10A_690V-10A,814S-PF3-480V-10A_690V-1 Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 440P Bulletin 440P DIN 50041 IEC/Large Metal Body Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 193-EGF E1 PLUS Ground Fault Accessory Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 140U N-Frame CB Alarm Switch and Alarm Auxiliary S Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 193-EGF E1 PLUS Ground Fault Accessory Module Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 190 Universal Instruction Sheet for Open Type Star Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 140M-D8E-... Motor Protection Circuit Breaker, Pro Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation 150-SCMx SMC-50 Soft Starter (210A - 320A & 36 Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 440L GuardShield Type 4 and Remote Teach User Manu Manual de usuario
(44 paginas)
(44 paginas)
Equipo Rockwell-automation 440P-WM1A Short Lever Installation/Operating Instr Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 20G PowerFlex 755 IP00 NEMA/UL Open Drive - Frames Manual de usuario
(76 paginas)
(76 paginas)
Equipo Rockwell-automation 150-Cxx SMC-3 Soft Starter MOV Protective Module I Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales