Rockwell-automation 47C626 AutoMax Programming Executive V4.2 Manual de usuario descargar pdf (Pagina 76)

5Ć42

See Appendix T for problems that can occur when you load

operating systems.

Types of AutoMax Operating Systems

e A

utoMax operating system, whic

h o

versees th

e o

peratio

n o

f t

AutoMax Processors and th

e e

xecutio

n o

f a

pplicatio

n t

asks

, i

s provided

n t

wo versions

: 6

011ĆEthernet an

d 7

010ĆStandard. Th

e 6

011

Ć E

thernet

operating syste

m c

n b

e l

oaded ont

o M

/N 57C43

1 P

rocessors

. In o

rder

o u

se th

e E

therne

t f

unctions that allow communicatio

n o

r E

thernet

using the TCP/IP protocol, a

n E

thernet Networ

k I

nterfac

e m

odul

e (

M/N

47C440)

t b

e i

nstalle

d i

n t

e r

k a

d t

e E

therne

t o

peratin

g s

ystem

must

e u

sed. Th

e E

thernet operating syste

m i

s also require

d i

f a

y o

e f

ollowin

g f

unctions ar

e u

d i

n B

ASIC tasks: READVAR%,

WRITEVAR%

, F

INDVAR!, and CONVERT%. Th

e 7

0 Ć S

tandard

operating system, whic

h s

upports al

l o

f t

e E

therne

t f

unctions, must be

used wit

h t

e M

N 5

7C43

5 P

rocessor.

When you load the AutoMax operating system to the Processor

modules in the rack, the Ethernet operating system will be loaded to

all

M/N 57C431 Processors. The 7010ĆStandard operating system will

be loaded to all M/N 57C435 Processors. The M/N 57C431 and

57C435 make 290K available for application tasks.

Time Required to Load Operating Systems

The operating system(s) will be loaded at the maximum baud rate

available for the Processor being used. If you are using 6010/6011

and 7010 Processors in the same rack, make sure that the leftmost

Processor is a 7010 (M/N 57C435) Processor

. This will allow the

operating system(s) to be loaded at 19200 baud. If the leftmost

Processor in the rack is a M/N 57C431, the operating system(s) will

be loaded at 9600 baud. At 9600 baud, it will require approximately

two minutes to load each operating system to the Processors in the

rack. If there are 6011 and 7010 Processors in the same rack, it will

take approximately twice as long as it would if there were only one

type of Processor in the rack. The UDC operating system requires

approximately four minutes to load to each UDC module in the rack.

What to Do Next

After loading the appropriate operating systems to the rack following

the

instructions below, you would normally load compiled application

tasks and (optionally) UDC drive parameters to the rack. See section

14.3 for more information.

5.4.3.1 Procedure for Loading All Operating Systems to the Rack

The flowchart in figure 5.25 illustrates the options you have when

loading the AutoMax operating systems and UDC operating systems

(if DPS drive software has been installed). Before loading the

operating system(s), review this flowchart carefully.

Use the steps that follow to initiate the Load Operating Systems

procedure.

Step 1. If you have not already done so, turn on the personal

computer and run the AutoMax Programming Executive.

Step 2. Turn on power to the rack. Note that if the AutoMax

Processors in the rack do not have an operating system,

the leftmost AutoMax Processor module in the rack will

display the letters L" and O" (reading top to bottom).

This code prompts you to load the operating system.

Because Processor modules have onboard battery

1 2 ... 71 72 73 74 75 76 77 78 79 80 81 ... 277 278

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 47C626 AutoMax Programming Executive V4.2 Manual de usuario Pagina 76

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 47C626 AutoMax Programming Executive V4.2