Rockwell-automation 1560E SMC Flex Smart Motor Controller Manual de usuario Pagina 19
- Pagina / 198
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Product Overview 1-9
%5-"%.0*UNE
Protection and Diagnostics The MV SMC-Flex™ controller is capable of providing the following
protective and diagnostic features:
Overload
The MV SMC-Flex controller meets applicable requirements as a motor
overload protection device. Thermal memory provides added protection
and is maintained even when control power is removed. The built-in
overload algorithm controls the value stored in Parameter 12, Motor
Thermal Usage (see Chapter 4, Programming). An Overload Fault will
occur when this value reaches 100%. The parameters below provide
application flexibility and easy setup.
Parameter Range
Overload Class Off, 10, 15, 20, 30
Overload Reset Manual – Auto
Motor FLC 1.0 – 1000.0 amps
ServiceFactor 0.01–1.99
Important: During slow speed operations, current waveforms exhibit
non-sinusoidal characteristics. These non-sinusoidal characteristics
inhibit the controller's current-measurement capability. To compensate
for additional motor heating that may result, the controller uses motor
thermal modeling, which increments motor thermal usage. This compen-
sation takes place when the Preset Slow Speed option is used.
Notes:
1. The factory default setting for Overload Class, which is "OFF", disables
overload protection. An overload trip class and the motor's full-load
current rating must be programmed to enable overload protection.
2. If the MV SMC-Flex is used to control a multi-speed motor, or more
than one motor, the Overload Class parameter must be programmed
to "OFF" and separate overload relays must be supplied for each
speed/motor.
3. Automatic reset of an overload fault requires the start input to be
cycled in a 2-wire control scheme.
4. The trip rating is 117% of the programmed FLC.
Figures 1.9 and 1.10 provide the overload trip curves for the available trip
classes.
- Medium Voltage 1
- SMC Flex™ 1
- Motor Controller 1
- Important User Information 2
- Table of Contents 3
- Installation Chapter 2 4
- Programming Chapter 4 5
- Metering Chapter 5 Page 6
- Options Chapter 6 6
- Diagnostics Chapter 7 6
- Communications Chapter 8 6
- Maintenance Chapter 10 7
- Appendix D Spare Parts 8
- Appendix E Accessories 8
- 1560E-UM050B-EN-P - June 2013 10
- Product Overview 11
- 1560E – Retrofit Controller 12
- SMC-Flex™ Control Module 12
- Figure 1.1– Soft Start 13
- Selectable Kickstart : 14
- Current Limit Start ; 14
- Dual Ramp Start : 15
- Full Voltage Start 15
- Preset Slow Speed 16
- Product Overview 1-7 17
- Soft Stop 18
- Overload 19
- Protection and Diagnostics 20
- Underload : 21
- Undervoltage ; 21
- Overvoltage ; 21
- Ground Fault 23
- Table 1.A –PTC Input Ratings 25
- Excessive Starts/Hour 27
- Overtemperature 27
- Figure 1.14 – DPI Location 28
- Pump Control Option 29
- 1-20 Product Overview 30
- Braking Control Option 31
- Power Module 32
- Interface Board 33
- 1-24 Product Overview 34
- Product Overview 1-25 35
- 1-26 Product Overview 36
- Product Overview 1-27 37
- 1-28 Product Overview 38
- 1-30 Product Overview 40
- Product Overview 1-31 41
- 1-32 Product Overview 42
- Product Overview 1-33 43
- Product Overview 1-35 45
- 1-36 Product Overview 46
- Product Overview 1-37 47
- 1-38 Product Overview 48
- Installation 49
- 2-2 Installation 50
- Mounting 51
- Grounding Practices 52
- (with LV panels not shown) 54
- Installation 2-7 55
- Installation 2-9 57
- Power Connections (cont.) 58
- Bulletin 1503E 59
- 2-12 Installation 60
- Installation 2-13 61
- 2-14 Installation 62
- Installation 2-15 63
- Surge Arrestor Protection 64
- Two-speed Motors 65
- Multi-motor Protection 65
- EMC Compliance 66
- Wire Size Torque 67
- 0.75 to 2.5 mm 67
- 2-20 Installation 68
- Commissioning Procedure 69
- System Characteristics 70
- MV SMC-Flex™ Module 71
- 3-4 Commissioning Procedures 72
- Commissioning Procedures 3-5 73
- 3-6 Commissioning Procedures 74
- Figure 3.3 – Interface PCB 75
- 3-8 Commissioning Procedures 76
- Milliseconds 77
- Control Function Tests 78
- Programming 81
- Programming Menu (cont.) 82
- Programming 4-3 83
- Table 4.A 84
- Parameter Linear List 84
- Programming 4-5 85
- EscEsc SelSel 86
- Using Parameter Management 87
- (Dual Ramp) 90
- Parameter Option 91
- Starting Mode 91
- Full Voltage 91
- Basic Setup (cont.) 92
- Undervoltage u 94
- Overvoltage u 94
- Underload v 94
- Motor Data Entry 95
- 4-16 Programming 96
- Metering 97
- Viewing Metering Data 98
- Human Interface Module 100
- Programming Parameters 102
- Options 6-5 103
- 6-6 Options 104
- Diagnostics 105
- 7-2 Diagnostics 106
- Table 7.A 107
- Fault Code Cross-Reference 107
- 7-4 Diagnostics 108
- Communications 109
- Keypad Description 110
- Communications 8-3 111
- Control Enable 112
- Communications 8-5 113
- Loss of Communication and 114
- Network Faults 114
- Table 8.E 115
- SMC-Flex Bit Identification 116
- Scale Factors for PLC 117
- Communication 117
- Rules for Using DataLinks 118
- Troubleshooting 119
- : Prestart fault indication 121
- Troubleshooting 9-5 123
- 9-6 Troubleshooting 124
- Voltage Feedback Circuit 125
- Voltage-Sensing Board 126
- Replacement 126
- Figure 9.3 – IGDPS Board 127
- 9-10 Troubleshooting 128
- Troubleshooting 9-11 129
- SCR Replacement Procedure 131
- Power Circuit 132
- Troubleshooting (cont.) 132
- Troubleshooting 9-15 133
- Troubleshooting 9-17 135
- Figure 9.6 – Heatsink Clamp 136
- Troubleshooting 9-19 137
- Figure 9.9 – Heatsink Clamp 138
- Troubleshooting 9-21 139
- Troubleshooting 9-23 141
- 9-24 Troubleshooting 142
- Troubleshooting 9-25 143
- Snubber and Resistor Circuit 145
- VOLTAGE FEEDBACK 146
- Troubleshooting 9-29 147
- 9-30 Troubleshooting 148
- Troubleshooting 9-31 149
- 9-32 Troubleshooting 150
- Troubleshooting 9-33 151
- 9-34 Troubleshooting 152
- Troubleshooting 9-35 153
- 9-36 Troubleshooting 154
- Troubleshooting 9-37 155
- 9-38 Troubleshooting 156
- Troubleshooting 9-39 157
- 9-40 Troubleshooting 158
- Maintenance 159
- Vacuum Bottles 160
- Terminals 160
- Solid-State Devices 161
- Static-Sensitive Items 161
- Final Check Out 161
- 10-4 Maintenance 162
- Environmental Considerations 163
- Appendix A 165
- A-2 Specifications 166
- Bulletin 1560E 169
- Bulletin 1562E 169
- Description Specifications 170
- Description 172
- Parameter Information 173
- Parameter Information B-3 175
- B-4 Parameter Information 176
- 1560E and 1562E Relay Control 177
- SMC-Flex module 178
- Spare Parts 187
- Table D.2 188
- Spare Parts D-3 189
- Table D.4 190
- Table D.6 192
- Table D.7 193
- Accessories 194
- Table D.8 194
- E-2 Accessories 196
Relacionado con productos y manuales para Equipo Rockwell-automation 1560E SMC Flex Smart Motor Controller
Equipo Rockwell-automation 1606-XLP60BQT Power Supply Reference Manual Manual de usuario
(24 paginas)
(24 paginas)
(42 paginas)
Equipo Rockwell-automation 1492-AIFMQS 4 Input / 4 Output Fusible Analog Inte Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 1492-CM800-LD009 Field Wire Conv. Module for Modic Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 1492-IFM20DS24-4_IFM20DS120-4 8 Point Isolated Int Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1512A MV Controllers - 800A One-High Cabinet Manual de usuario
(105 paginas)
(105 paginas)
Equipo Rockwell-automation 1492-XIMTRxxx_RXIMTRxxx 16 and 32 Point Relay Inte Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 1585BP Bulkhead Coupler Installation Instructions Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1492-CM1771-LD001 Digital I/O Conversion Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1102C-PKxx 400A / 600A Vacuum Contactor AC Coil Re Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1336T Function Block Prog. Manual, Series A/B Manual de usuario
(180 paginas)
(180 paginas)
(43 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales